View previous topic :: View next topic |
Author |
Message |
freax n00b
Joined: 28 Aug 2007 Posts: 24
|
Posted: Sun Nov 02, 2008 12:45 am Post subject: [Risolto] problemi con eth0 all'avvio |
|
|
salve ragazzi , dopo un certo tempo passato a provare le varie distro ho scelto di passare definitivamente a Gentoo , ho seguito la guida italiana passo per passo ovvero questa http://www.gentoo.org/doc/it/handbook/handbook-x86.xml?full=1 ed ho un problema con eth0 i cui driver non vengono visti dal sistema .
Per la compilazione del kernel ho optato per una configurazione manuale quindi non ho usato genkernel e adesso non capisco il perché ciò che ho selezionato in fase di pre-compilazione non sia andato come doveva ...
nel dubbio ho postato un po tutti i dati riguardanti il mio piccolo sistema (è un thinclient HP T5510 con processore Transmeta Geode 800Mhz e 512mb ram e 8Gb di HDD) .
i comandi postati sono , in ordine :
- lspci
- lspci -vv
- /etc/init.d/net.eth0 start
- il file di configurazione della rete /etc/conf.d/net
- lsmod
ho letto varie documentazioni e cercato un po con google ma niente risolve il mio problema , ho anche letto che il chipset VIA che gestisce la rete è ottimamente supportato sotto linux , perciò mi chiedo dove sia il problema ...
ho anche letto che probabilmente ci potrebbe essere un conflitto tra la bash e l'avvio dello script che inizializza la rete , ma sinceramente non so come verificare ciò ...
Come faccio ad essere sicuro che il kernel sia stato compilato inglobando anche i driver giusti e che il problema sia da ricercare altrove ? Esiste un modo per sapere una configurazione certa e funzionante da adottare in fase di configurazione delle compilazione del kernel con il mio hardware ?
Grazie
Code: | 00:00.0 Host bridge: Transmeta Corporation LongRun Northbridge (rev 04)
00:00.1 RAM memory: Transmeta Corporation SDRAM controller
00:00.2 RAM memory: Transmeta Corporation BIOS scratchpad
00:00.3 RAM memory: Transmeta Corporation Device 0399
00:09.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61)
00:09.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61)
00:09.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63)
00:0d.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE]
00:11.0 ISA bridge: VIA Technologies, Inc. VT8231 [PCI-to-ISA Bridge] (rev 10)
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:11.4 Bridge: VIA Technologies, Inc. VT8235 ACPI (rev 10)
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 40)
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 51)
-----------
-----------
-----------
00:00.0 Host bridge: Transmeta Corporation LongRun Northbridge (rev 04)
Subsystem: Transmeta Corporation Device 0295
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 32
Region 0: Memory at e8000000 (32-bit, non-prefetchable) [size=1M]
00:00.1 RAM memory: Transmeta Corporation SDRAM controller
Subsystem: Transmeta Corporation Device 0295
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.2 RAM memory: Transmeta Corporation BIOS scratchpad
Subsystem: Transmeta Corporation Device 0295
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.3 RAM memory: Transmeta Corporation Device 0399
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:09.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 15
Region 4: I/O ports at e000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: uhci_hcd
00:09.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at e100 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: uhci_hcd
00:09.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 10
Region 0: Memory at e8131000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd
00:0d.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE] (prog-if 00 [VGA controller])
Subsystem: ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at e200 [size=256]
Region 2: Memory at e8120000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at 20000000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8231 [PCI-to-ISA Bridge] (rev 10)
Subsystem: VIA Technologies, Inc. Device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at e300 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.4 Bridge: VIA Technologies, Inc. VT8235 ACPI (rev 10)
Subsystem: VIA Technologies, Inc. VT8235 ACPI
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 40)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at e600 [size=256]
Region 1: I/O ports at e700 [size=4]
Region 2: I/O ports at e800 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 51)
Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded Ethernet Controller on VT8235
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 15
Region 0: I/O ports at e900 [size=256]
Region 1: Memory at e8130000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-----------
-----------
-----------
do il comando /etc/init.d/net.eth0 start e :
[32;01m*[0m Starting eth0
[32;01m*[0m Bringing up eth0
[32;01m*[0m 192.168.1.37
[31;01m*[0m network interface eth0 does not exist
[31;01m*[0m Please verify hardware or kernel module (driver)
[A[72C [34;01m[ [31;01m!![34;01m ][0m
[A[72C [34;01m[ [31;01m!![34;01m ][0m
-----------
-----------
-----------
# This blank configuration will automatically use DHCP for any net.*
# scripts in /etc/init.d. To create a more complete configuration,
# please review /etc/conf.d/net.example and save your configuration
# in /etc/conf.d/net (this file :]!).
config_eth0=("192.168.1.37 netmask 255.255.255.0 brd 192.168.1.255")
routes_eth0=("default gw 192.168.1.1")
-----------
-----------
-----------
output lsmod
Module Size Used by
scsi_wait_scan 1280 0
|
Last edited by freax on Sun Nov 02, 2008 10:39 pm; edited 1 time in total |
|
Back to top |
|
|
fbcyborg Advocate
Joined: 16 Oct 2005 Posts: 3056 Location: ROMA
|
|
Back to top |
|
|
freax n00b
Joined: 28 Aug 2007 Posts: 24
|
Posted: Sun Nov 02, 2008 10:23 am Post subject: |
|
|
fbcyborg wrote: | Quando hai installato la gentoo, immagino che tu abbia usato il live cd (magari uno di quelli esterni, USB).
La rete funzionava? eth0 era presente?
In caso affermativo, che modulo veniva caricato? Confronta l'output di lsmod quando sei nel livecd con quello di quando hai avviato gentoo normalmente.
Non vorrei che tu avessi compilato un modulo errato per l'appunto. |
ho installato 2 ore prima che postassi ...
in effetti in fase di installazione con il cd "minimal x86 2008.0" non ho avuto problemi a fargli riconoscere la rete e ho solo dovuto configurare eth0 con net-setup .
Siccome è vero che conosco bene l'ambiente linux ma ho poca esperienza con la compilazione del kernel , secondo te è meglio ricompilare o caricare i driver come modulo all'avvio ? Se scarico i sorgenti del kernel da kernel.org cosa succede ? |
|
Back to top |
|
|
fbcyborg Advocate
Joined: 16 Oct 2005 Posts: 3056 Location: ROMA
|
Posted: Sun Nov 02, 2008 10:46 am Post subject: |
|
|
La procedura che io farei è quella che ti ho già detto: comparare l'lsmod nei due casi, vedere qual'è il modulo della scheda di rete che viene caricato, verificare che sia compilato nel kernel di Linux e cricarlo, qualora sia compilato come modulo e non built-in.
Per i sorgenti del kernel da kernel.org, puoi fare come vuoi, è una pura scelta personale. Io preferisco i gentoo-sources, patchati e fatti apposta per gentoo. In caso volessi i sorgenti da kernel.org basterebbe un semplice Code: | emerge vanilla-sources | ma per ora te lo sconsiglio, il problema è un altro. Non c'entra niente che sorgenti stai usando.
postami un _________________ [HOWTO] Come criptare la /home usando cryptsetup e luks
[HOWTO] Abilitare il supporto al dom0 XEN su kernel 3.X
Help answer the unanswered |
|
Back to top |
|
|
freax n00b
Joined: 28 Aug 2007 Posts: 24
|
Posted: Sun Nov 02, 2008 11:53 am Post subject: |
|
|
fbcyborg wrote: | La procedura che io farei è quella che ti ho già detto: comparare l'lsmod nei due casi, vedere qual'è il modulo della scheda di rete che viene caricato, verificare che sia compilato nel kernel di Linux e cricarlo, qualora sia compilato come modulo e non built-in.
Per i sorgenti del kernel da kernel.org, puoi fare come vuoi, è una pura scelta personale. Io preferisco i gentoo-sources, patchati e fatti apposta per gentoo. In caso volessi i sorgenti da kernel.org basterebbe un semplice Code: | emerge vanilla-sources | ma per ora te lo sconsiglio, il problema è un altro. Non c'entra niente che sorgenti stai usando.
postami un |
ho dato una occhiata all'output di lsmod con la live cd , o meglio con il cd minimal x86 avviato , e sembra che sia mii a gestire il chipset della rete ...
Code: | Module Size Used by
dock 18448 0
video 26640 0
backlight 13188 1 video
output 11776 1 video
ac 12544 0
battery 16640 0
fan 12804 0
via_rhine 31496 0
mii 13312 1 via_rhine
thermal 24092 0
processor 39656 2 thermal
button 16528 0
rtc 20768 0
tg3 111748 0
e1000 119616 0
jfs 169836 0
raid10 30080 0
raid456 129296 0
async_memcpy 10880 1 raid456
async_xor 12160 1 raid456
xor 21896 2 raid456,async_xor
async_tx 15948 3 raid456,async_memcpy,async_xor
raid1 30080 0
raid0 15872 0
dm_bbr 20128 0
dm_snapshot 24996 0
dm_mirror 29440 0
dm_mod 63428 3 dm_bbr,dm_snapshot,dm_mirror
sbp2 29960 0
ohci1394 38192 0
ieee1394 92600 2 sbp2,ohci1394
sl811_hcd 19968 0
usbhid 35712 0
ohci_hcd 29700 0
uhci_hcd 30988 0
usb_storage 120608 1
ehci_hcd 39948 0
usbcore 133484 7 sl811_hcd,usbhid,ohci_hcd,uhci_hcd,usb_storage,ehci_hcd
lpfc 216016 0
qla2xxx 168548 0
firmware_class 17408 1 qla2xxx
megaraid_sas 35504 0
megaraid_mbox 38160 0
megaraid_mm 18464 1 megaraid_mbox
megaraid 44360 0
aacraid 68996 0
sx8 25484 0
DAC960 73032 0
cciss 41220 0
cpqarray 28004 0
3w_9xxx 39300 0
3w_xxxx 32928 0
mptsas 43144 0
scsi_transport_sas 37120 1 mptsas
mptfc 25988 0
scsi_transport_fc 49028 3 lpfc,qla2xxx,mptfc
scsi_tgt 22344 1 scsi_transport_fc
mptspi 28296 0
mptscsih 41344 3 mptsas,mptfc,mptspi
mptbase 78308 4 mptsas,mptfc,mptspi,mptscsih
atp870u 36352 0
dc395x 39052 0
sim710 13188 0
53c700 33444 1 sim710
qla1280 123660 0
dmx3191d 20096 0
sym53c8xx 77588 0
qlogicfas408 15104 0
aha152x 42512 0
aha1740 15872 0
advansys 85248 0
initio 24900 0
BusLogic 72948 0
arcmsr 29952 0
aic7xxx 168760 0
aic79xx 241624 0
scsi_transport_spi 30848 7 mptspi,53c700,dmx3191d,sym53c8xx,aha152x,aic7xxx,aic79xx
sg 41360 0
pdc_adma 17668 0
sata_inic162x 20228 0
sata_mv 28936 0
ata_piix 26372 0
ahci 34180 0
sata_qstor 17924 0
sata_vsc 16516 0
sata_uli 15620 0
sata_sis 16772 0
sata_sx4 20484 0
sata_nv 33160 0
sata_via 19588 0
sata_svw 15748 0
sata_sil24 24068 0
sata_sil 19080 0
sata_promise 20996 0
scsi_wait_scan 9472 0
pata_sis 21892 1 sata_sis
libata 152248 17 pdc_adma,sata_inic162x,sata_mv,ata_piix,ahci,sata_qstor,sata_vsc,sata_uli,sata_sis,sata_sx4,sata_nv,sata_via,sata_svw,sata_sil24,sata_sil,sata_promise,pata_sis
|
ecco quindi anche l'output di lspci -n
Code: | 00:00.0 0600: 1279:0395 (rev 04)
00:00.1 0500: 1279:0396
00:00.2 0500: 1279:0397
00:00.3 0500: 1279:0399
00:09.0 0c03: 1106:3038 (rev 61)
00:09.1 0c03: 1106:3038 (rev 61)
00:09.2 0c03: 1106:3104 (rev 63)
00:0d.0 0300: 1002:5159
00:11.0 0601: 1106:8231 (rev 10)
00:11.1 0101: 1106:0571 (rev 06)
00:11.4 0680: 1106:8235 (rev 10)
00:11.5 0401: 1106:3058 (rev 40)
00:12.0 0200: 1106:3065 (rev 51)
|
EDIT : visto che con la nuova installazione sono già in ambiente gentoo non dovrei neanche scaricare nulla ... solo ricompilare il kernel ... giusto ? |
|
Back to top |
|
|
fbcyborg Advocate
Joined: 16 Oct 2005 Posts: 3056 Location: ROMA
|
|
Back to top |
|
|
freax n00b
Joined: 28 Aug 2007 Posts: 24
|
Posted: Sun Nov 02, 2008 1:03 pm Post subject: |
|
|
fbcyborg wrote: | Il driver della tua scheda di rete è via-rhine ed è supportato dal kernel di Linux (sicuramente dal 2.6.25 in poi).
Assicurati che tale driver sia compilato nel kernel (o come modulo o built-in) e la rete non avrà problemi a funzionare.
Ricompila il kernel con quel driver! |
ok , perfetto , e fin qui ci siamo , intanto ti ringrazio per il tempo che mi stai dedicando , ma una domanda mi sorge spontanea : esiste qualche utility che si appoggi all'output di comandi come lspci e confronti automaticamente ciò che "vede" con i sorgenti del kernel per suggerire la giusta configurazione (come DKMS più o meno , ma in fase di compilazione) ? Che problemi mi potrebbe dare il voler adottare i sorgenti vanilla da kernel.org ? |
|
Back to top |
|
|
fbcyborg Advocate
Joined: 16 Oct 2005 Posts: 3056 Location: ROMA
|
|
Back to top |
|
|
freax n00b
Joined: 28 Aug 2007 Posts: 24
|
Posted: Sun Nov 02, 2008 3:28 pm Post subject: |
|
|
ottimo , quel link non lo conoscevo
procedo a ricompilare il kernel dal nuovo ambiente e ritento ... |
|
Back to top |
|
|
freax n00b
Joined: 28 Aug 2007 Posts: 24
|
Posted: Sun Nov 02, 2008 10:38 pm Post subject: |
|
|
tutto ok , un consiglio per chi verrà dopo di me ed avrà lo stesso problema , sembrava abbastanza laborioso compilare un kernel per la mia macchina , ma se incollate l'output di nel sito che mi ha passato fbcyborg http://kmuto.jp/debian/hcl/ e andando a dare vi appoggiate al comando di ricerca interno premendo il tasto (segno di divisione) è una cosa da bambini ...
grazie 1000 fbcyborg metto come risolto |
|
Back to top |
|
|
fbcyborg Advocate
Joined: 16 Oct 2005 Posts: 3056 Location: ROMA
|
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|