View previous topic :: View next topic |
Author |
Message |
sirion n00b
Joined: 03 Jul 2005 Posts: 15
|
Posted: Mon Jun 18, 2007 12:24 pm Post subject: ALSA & chip audio MCP51 ALC883, suono distorto! |
|
|
Il mio problema mi sta tormentando da tanto, tanto tempo, da Febbraio per la precisione, ho cercato su google, ricercato i forum guardato guide, provato drivers, potrei quasi scriverci una guida io stesso di questa odissea, comunque ora descrivo il problema.
Ho provato ubuntu Feisty Fawn 7.04 alla prima installazione il suono si sentiva leggermente, ma era tremendamente gracchiante (Feisty Fawn ha di default ALSA 1.0.13). Allora ho cominciato a ricercare il problema so google: ho provato ad aggiornare ALSA all'ultima stabile sul sito (1.0.14) ma niente stesso problema suono distorto, ho letto la documentazione e ho provato alcune opzioni per i file di configurazione di ALSA :
come :
options snd-hda-intel model=3stack-dig (suono distorto)
oppure:
options snd-hda-intel model=6stack-dig (suono distorto)
oppure:
options snd-hda-intel index=0,1 model=3stack-dig (nessun suono)
oppure:
options snd-hda-intel position_fix=1 o 2 con o single_cmd=1 (spesso nessun suono)
ed altro ancora... alla fine andavo quasi a caso.
Niente da fare, altre opzioni non le conosco non ho trovato la documentazione sul sito di ALSA (sito un po' scomodo da ricercare tra l'altro).
Ho provato ad installare anche OSS su Fawn ma sempre stessa cosa, suono gracchiante.
Sono passato a Gentoo visto che avevo già intenzione di reinstallarla.
Stessa cosa in gentoo, suono udibile ma distorto (sempre i soliti rumori di interferenza), comincio a pensare che non riguardi i driver sonori, ma qualcosa come un conflitto IRQ (anche se nel 2007 ero convinto che fossero storia vecchia), ma non saprei come indagare il problema.
ecco l'hardware:
cat /proc/asound/cards:
Code: |
0 [NVidia ]: HDA-Intel - HDA NVidia
HDA NVidia at 0xfe024000 irq 16
|
cat /proc/asound/version:
Advanced Linux Sound Architecture Driver Version 1.0.14.
Compiled on Jun 18 2007 for kernel 2.6.20-gentoo-r8 (SMP)
lspci -vv
Code: |
00:00.0 Host bridge: nVidia Corporation Unknown device 03a3 (rev a2)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [40] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd-
Link Control: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 0.16
00:00.1 RAM memory: nVidia Corporation Unknown device 03ac (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.2 RAM memory: nVidia Corporation Unknown device 03aa (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.3 RAM memory: nVidia Corporation Unknown device 03a9 (rev a1)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.4 RAM memory: nVidia Corporation Unknown device 03ab (rev a1)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.5 RAM memory: nVidia Corporation Unknown device 03a8 (rev a2)
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.6 RAM memory: nVidia Corporation Unknown device 03b5 (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:00.7 RAM memory: nVidia Corporation Unknown device 03b4 (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:01.0 RAM memory: nVidia Corporation Unknown device 03ad (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:01.1 RAM memory: nVidia Corporation Unknown device 03ae (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:01.2 RAM memory: nVidia Corporation Unknown device 03af (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:01.3 RAM memory: nVidia Corporation Unknown device 03b0 (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:01.4 RAM memory: nVidia Corporation Unknown device 03b1 (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:01.5 RAM memory: nVidia Corporation Unknown device 03b2 (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:01.6 RAM memory: nVidia Corporation Unknown device 03b3 (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:02.0 RAM memory: nVidia Corporation Unknown device 03b6 (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:02.1 RAM memory: nVidia Corporation Unknown device 03bc (rev a1)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:02.2 RAM memory: nVidia Corporation Unknown device 03ba (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:03.0 PCI bridge: nVidia Corporation Unknown device 03b7 (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fa000000-fcffffff
Prefetchable memory behind bridge: 00000000e0000000-00000000eff00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
Address: 00000000fee0300c Data: 41a9
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 0
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
00:05.0 PCI bridge: nVidia Corporation Unknown device 03b8 (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fdf00000-fdffffff
Prefetchable memory behind bridge: 00000000fde00000-00000000fde00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
Address: 00000000fee0300c Data: 41b1
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x0, ASPM L0s, Port 1
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
00:06.0 PCI bridge: nVidia Corporation Unknown device 03b9 (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: 00000000fdc00000-00000000fdc00000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
Address: 00000000fee0300c Data: 41b9
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 3
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
00:07.0 PCI bridge: nVidia Corporation Unknown device 03bb (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fd900000-fd9fffff
Prefetchable memory behind bridge: 00000000fd800000-00000000fd800000
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
Address: 00000000fee0300c Data: 41c1
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 2
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2)
Subsystem: ASUSTeK Computer Inc. Unknown device 81bc
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=9 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config 0: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 1.0GHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [e0] HyperTransport: MSI Mapping
00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a3)
Subsystem: ASUSTeK Computer Inc. Unknown device 81bc
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a3)
Subsystem: ASUSTeK Computer Inc. Unknown device 81bc
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 1c00 [size=64]
Region 5: I/O ports at 1c80 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.2 RAM memory: nVidia Corporation MCP51 Memory Controller 0 (rev a3)
Subsystem: ASUSTeK Computer Inc. Unknown device 81bc
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81bc
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe02f000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81bc
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 16
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device 81bc
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at fd00 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 81bc
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at f800 [size=16]
Region 5: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Message Signalled Interrupts: 64bit+ Queue=0/2 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping
00:0f.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 81bc
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 09e0 [size=8]
Region 1: I/O ports at 0be0 [size=4]
Region 2: I/O ports at 0960 [size=8]
Region 3: I/O ports at 0b60 [size=4]
Region 4: I/O ports at f300 [size=16]
Region 5: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Message Signalled Interrupts: 64bit+ Queue=0/2 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping
00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=128
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fdb00000-fdbfffff
Prefetchable memory behind bridge: fda00000-fdafffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [b8] #0d [0000]
Capabilities: [8c] HyperTransport: MSI Mapping
00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2)
Subsystem: ASUSTeK Computer Inc. Unknown device 8249
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin B routed to IRQ 16
Region 0: Memory at fe024000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] HyperTransport: MSI Mapping
00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a3)
Subsystem: ASUSTeK Computer Inc. Unknown device 8221
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at f200 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation G70 [GeForce 7600 GT] (rev a1) (prog-if 00 [VGA])
Subsystem: XFX Pine Group Inc. Unknown device 2220
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fb000000 (64-bit, non-prefetchable) [size=16M]
Region 5: I/O ports at cf00 [size=128]
[virtual] Expansion ROM at fcfe0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <256ns, L1 <4us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Capabilities: [100] Virtual Channel
Capabilities: [128] Power Budgeting
04:00.0 SATA controller: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Unknown device 8208
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at df00 [size=8]
Region 1: I/O ports at de00 [size=4]
Region 2: I/O ports at dd00 [size=8]
Region 3: I/O ports at dc00 [size=4]
Region 4: I/O ports at db00 [size=16]
Region 5: Memory at fd9fe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Express Legacy Endpoint IRQ 1
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 1
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
05:08.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev c0) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81fe
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fdbff000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at bf00 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
dmesg
Code: |
Linux version 2.6.20-gentoo-r8 (root@livecd) (gcc version 4.1.1 (Gentoo 4.1.1-r3)) #1 SMP Sat Jun 16 02:51:08 CEST 2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009f000 end: 000000000009f000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009f000 size: 0000000000001000 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000003fdf0000 end: 000000003fef0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000003fef0000 size: 0000000000003000 end: 000000003fef3000 type: 4
copy_e820_map() start: 000000003fef3000 size: 000000000000d000 end: 000000003ff00000 type: 3
copy_e820_map() start: 00000000f0000000 size: 0000000002000000 end: 00000000f2000000 type: 2
copy_e820_map() start: 00000000fec00000 size: 0000000001400000 end: 0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fef0000 (usable)
BIOS-e820: 000000003fef0000 - 000000003fef3000 (ACPI NVS)
BIOS-e820: 000000003fef3000 - 000000003ff00000 (ACPI data)
BIOS-e820: 00000000f0000000 - 00000000f2000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
126MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f5b50
Entering add_active_range(0, 0, 261872) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 261872
early_node_map[1] active PFN ranges
0: 0 -> 261872
On node 0 totalpages: 261872
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 253 pages used for memmap
HighMem zone: 32243 pages, LIFO batch:7
DMI 2.4 present.
ACPI: RSDP (v002 Nvidia ) @ 0x000f75d0
ACPI: XSDT (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x3fef30c0
ACPI: FADT (v003 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x3fef9640
ACPI: HPET (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000098) @ 0x3fef9880
ACPI: MCFG (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x3fef9900
ACPI: MADT (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x3fef9780
ACPI: DSDT (v001 NVIDIA ASUSACPI 0x00001000 MSFT 0x03000000) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x10de8201 base: 0xfeff0000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3ff00000:b0100000)
Detected 2400.058 MHz processor.
Built 1 zonelists. Total pages: 259827
Kernel command line: root=/dev/ram0 video=vesa:ywrap,mtrr vga=0x31A init=/linuxrc ramdisk=8192 real_root=/dev/sda7 udev
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0540000 soft=c0520000
PID hash table entries: 4096 (order: 12, 16384 bytes)
spurious 8259A interrupt: IRQ7.
Speakup v-2.00 CVS: Sat Oct 7 10:52:29 EDT 2006 : initialized
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1030220k/1047488k available (3116k kernel code, 16536k reserved, 820k data, 240k init, 129984k highmem)
virtual kernel memory layout:
fixmap : 0xffe17000 - 0xfffff000 (1952 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc04df000 - 0xc051b000 ( 240 kB)
.data : 0xc040b232 - 0xc04d8414 ( 820 kB)
.text : 0xc0100000 - 0xc040b232 (3116 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Using HPET for base-timer
Calibrating delay using timer specific routine.. 4803.17 BogoMIPS (lpj=24015888)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c0541000 soft=c0521000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4800.03 BogoMIPS (lpj=24000170)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00003940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
Total of 2 processors activated (9603.21 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=168
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
mtrr: your CPUs had inconsistent fixed MTRR settings
mtrr: probably your BIOS does not setup all CPUs.
mtrr: corrected configuration.
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:10.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:01: ioport range 0x1000-0x107f could not be reserved
pnp: 00:01: ioport range 0x1080-0x10ff has been reserved
pnp: 00:01: ioport range 0x1400-0x147f has been reserved
pnp: 00:01: ioport range 0x1480-0x14ff could not be reserved
pnp: 00:01: ioport range 0x1800-0x187f has been reserved
pnp: 00:01: ioport range 0x1880-0x18ff has been reserved
PCI: Bridge: 0000:00:03.0
IO window: c000-cfff
MEM window: fa000000-fcffffff
PREFETCH window: e0000000-efffffff
PCI: Bridge: 0000:00:05.0
IO window: a000-afff
MEM window: fdf00000-fdffffff
PREFETCH window: fde00000-fdefffff
PCI: Bridge: 0000:00:06.0
IO window: e000-efff
MEM window: fdd00000-fddfffff
PREFETCH window: fdc00000-fdcfffff
PCI: Bridge: 0000:00:07.0
IO window: d000-dfff
MEM window: fd900000-fd9fffff
PREFETCH window: fd800000-fd8fffff
PCI: Bridge: 0000:00:10.0
IO window: b000-bfff
MEM window: fdb00000-fdbfffff
PREFETCH window: fda00000-fdafffff
PCI: Setting latency timer of device 0000:00:03.0 to 64
PCI: Setting latency timer of device 0000:00:05.0 to 64
PCI: Setting latency timer of device 0000:00:06.0 to 64
PCI: Setting latency timer of device 0000:00:07.0 to 64
PCI: Setting latency timer of device 0000:00:10.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2508k freed
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1182172569.360:1): initialized
highmem bounce pool size: 64 pages
squashfs: version 3.2 (2007/01/02) Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
OCFS2 1.3.3
OCFS2 Node Manager 1.3.3
OCFS2 DLM 1.3.3
OCFS2 DLMFS 1.3.3
OCFS2 User DLM kernel interface loaded
GFS2 (built Jun 16 2007 02:49:31) installed
Lock_Nolock (built Jun 16 2007 02:49:36) installed
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
PCI: Setting latency timer of device 0000:00:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie03]
PCI: Setting latency timer of device 0000:00:05.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:05.0:pcie00]
Allocate Port Service[0000:00:05.0:pcie03]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
Allocate Port Service[0000:00:06.0:pcie03]
PCI: Setting latency timer of device 0000:00:07.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:07.0:pcie00]
Allocate Port Service[0000:00:07.0:pcie03]
initialized device: /dev/synth, node ( MAJOR 10, MINOR 25 )
vesafb: framebuffer at 0xe0000000, mapped to 0xf8880000, using 5120k, total 262144k
vesafb: mode is 1280x1024x16, linelength=2560, pages=1
vesafb: protected mode interface info at c000:c340
vesafb: pmi: set display start = c00cc376, set palette = c00cc3e0
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 160x64
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0
NFORCE-MCP51: chipset revision 161
NFORCE-MCP51: not 100% native mode: will probe irqs later
NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller
ide0: BM-DMA at 0xfd00-0xfd07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfd08-0xfd0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hdb: Maxtor 6L200P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: TSSTcorpCD/DVDW SH-S182D, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdb: max request size: 512KiB
hdb: 398297088 sectors (203928 MB) w/8192KiB Cache, CHS=24792/255/63<6>hdb: hw_config=6b00
, UDMA(133)
hdb: cache flushes supported
hdb: hdb1 hdb2 < hdb5 >
hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 240k freed
Time: tsc clocksource has been installed.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [APCL] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:0b.1 to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0b.1: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:0b.1
ehci_hcd 0000:00:0b.1: irq 16, io mem 0xfe02e000
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 22 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0b.0: irq 17, io mem 0xfe02f000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
usb 2-3: new low speed USB device using ohci_hcd and address 2
usb 2-3: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input1
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:0b.0-3
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
sl811: driver sl811-hcd, 19 May 2005
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:05:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[fdbff000-fdbff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
libata version 2.00 loaded.
sata_nv 0000:00:0e.0: version 3.2
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 21 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:0e.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xF800 irq 19
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xF808 irq 19
scsi0 : sata_nv
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 1
ata1.00: configured for UDMA/133
scsi1 : sata_nv
ata2: SATA link down (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0x977
scsi 0:0:0:0: Direct-Access ATA ST3250820AS 3.AA PQ: 0 ANSI: 5
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
sd 0:0:0:0: Attached scsi disk sda
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APSJ] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:0f.0 to 64
ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xF300 irq 20
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xF308 irq 20
scsi2 : sata_nv
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800011bc02d]
ata3: SATA link down (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0x9E7
scsi3 : sata_nv
ata4: SATA link down (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0x967
ahci 0000:04:00.0: version 2.0
ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16
ACPI: PCI Interrupt 0000:04:00.0[A] -> Link [APC6] -> GSI 16 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:04:00.0 to 64
ahci 0000:04:00.0: AHCI 0001.0000 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
ahci 0000:04:00.0: flags: 64bit ncq pm led clo pmp pio slum part
ata5: SATA max UDMA/133 cmd 0xF8E34100 ctl 0x0 bmdma 0x0 irq 21
scsi4 : ahci
ata5: SATA link down (SStatus 0 SControl 300)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
JFS: nTxBlock = 8072, nTxLock = 64582
Intel(R) PRO/1000 Network Driver - version 7.3.15-k2
Copyright (c) 1999-2006 Intel Corporation.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
sd 0:0:0:0: Attached scsi generic sg0 type 0
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [AAZA] -> GSI 23 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:10.1 to 64
input: PC Speaker as /class/input/input2
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.59.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
Linux agpgart interface v0.101 (c) Dave Jones
nvidia: module license 'NVIDIA' taints kernel.
hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [APCH] -> GSI 22 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:14.0 to 64
forcedeth: using HIGHDMA
eth1: forcedeth.c: subsystem: 01043:8221 bound to 0000:00:14.0
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x1c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x1c80
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC5] -> GSI 16 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8776 Mon Oct 16 21:56:04 PDT 2006
EXT3 FS on sda7, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2048248k swap on /dev/sda6. Priority:-1 extents:1 across:2048248k
Real Time Clock Driver v1.12ac
**WARNING** I2C adapter driver [NVIDIA I2C Device] forgot to specify physical device; fix it!
**WARNING** I2C adapter driver [NVIDIA I2C Device] forgot to specify physical device; fix it!
**WARNING** I2C adapter driver [NVIDIA I2C Device] forgot to specify physical device; fix it!
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hdb5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS driver 2.1.28 [Flags: R/O MODULE].
NTFS volume version 3.1.
NTFS volume version 3.1.
|
il modulo hda-codec non riconosce la scheda e fa un ricerca nel bios (azione di default secondo i doc di alsa), ma non credo sia quello il problema, oss aveva gli stessi problemi di suono gracchiante.
Ho provato anche il linuxsoundpack fornito dalla realtek (sembra solo una versione auto compilante ed installante di alsa, ma non so se hanno modificato i sorgenti) ma non cambia nulla.
Non so come indagare il problema, se fosse un conflitto IRQ (che per ora è l'unica supposizione che mi sono fatto) come faccio a trovarlo ?
Grazie per il vostro tempo! _________________ si, sono noob... |
|
Back to top |
|
|
jiojio74 n00b
Joined: 12 Jan 2007 Posts: 24
|
Posted: Mon Jun 18, 2007 2:29 pm Post subject: |
|
|
Ci provo: non è che non si tratta di un problema software?
Altra ipotesi: i volumi di alsa sono tutti al massimo? A volte mi è capitato di sentir gracchiare le casse quando sparavo il volume di alsa al massimo e quello delle casse a poco. Il giusto, credo, sia un compromesso fra i due.
Le casse attaccate ad altri dispositivi non hanno problemi? |
|
Back to top |
|
|
sirion n00b
Joined: 03 Jul 2005 Posts: 15
|
Posted: Mon Jun 18, 2007 2:52 pm Post subject: |
|
|
Spe mi spiego meglio... non è che gracchia sempre in maniera uniforme come se il volume fosse troppo sparato, il suono è discontinuo, ogni tanto sento qualcosa ma sopra quando il suono si sente c'è una quantità improponibile di rumore di disturbo, i volumi son a posto ormai ho installato alsa abb volte da controllare i volumi mi automaticamente.
ho solo un jack per le casse, dei jack frontali va solo il mic, e la cosa abb strana che ho scoperto ora è che se parlo nel mic sento la mia voce senza distorsione.
non so più a cosa pensare, forse qualcosa che non va in gstreamer, ma ho provato a lanciare un mp3 da console (senza avviare gnome) ma i rumori ci sono.
Mah... continuo a brancolare nel buio.
grazie per la risposta! _________________ si, sono noob... |
|
Back to top |
|
|
djinnZ Advocate
Joined: 02 Nov 2006 Posts: 4831 Location: somewhere in L.O.S.
|
Posted: Mon Jun 18, 2007 3:53 pm Post subject: |
|
|
Primo abilita hda-intel (in make.conf ALSA_CARDS) e prova anche ati/ali5xxx come device (sono fuori quindi non posso verificare in alcun modo).
Non è che c'è un jumper o una opzione nel bios per usare una uscita amplificata?
Per quanto riguarda i conflitti irq prova se succede qualcosa usando pci=routeirq etc.
Per fare una prima verifica all'acpi vedi [url]qui[/url]. Installa il compilatore (è in portage non ci vuole molto) e prova a ricompilare la dsdt. Se ti da errore puoi provare a fixarla altrimenti non ti fissare. _________________ scita et risus abundant in ore stultorum sed etiam semper severi insani sunt
mala tempora currunt...mater stultorum semper pregna est
Murpy'sLaw:If anything can go wrong, it will - O'Toole's Corollary:Murphy was an optimist |
|
Back to top |
|
|
Scen Retired Dev
Joined: 29 Jul 2003 Posts: 2470 Location: Padova, Italy
|
Posted: Mon Jun 18, 2007 4:28 pm Post subject: |
|
|
djinnZ wrote: | Per fare una prima verifica all'acpi vedi [url]qui[/url]. |
Manca l'URL _________________ I was born in a deep forest/I wish I could live here all my life/I am made from stones and roots/My home, these woods and roads
All my life I loved this sound/Of the woods all around/Eagles flies where the winds blows free
Journey is my destiny |
|
Back to top |
|
|
djinnZ Advocate
Joined: 02 Nov 2006 Posts: 4831 Location: somewhere in L.O.S.
|
Posted: Mon Jun 18, 2007 4:52 pm Post subject: |
|
|
Uff...
Non facevi prima a riportarlo direttamente?
Fa caldo ed il maledetto programma di stampa (odio il periodo delle dichiarazioni) mi interrompe di continuo per conferma del piffero mentre digito.
cmq è questo. _________________ scita et risus abundant in ore stultorum sed etiam semper severi insani sunt
mala tempora currunt...mater stultorum semper pregna est
Murpy'sLaw:If anything can go wrong, it will - O'Toole's Corollary:Murphy was an optimist |
|
Back to top |
|
|
sirion n00b
Joined: 03 Jul 2005 Posts: 15
|
Posted: Mon Jun 18, 2007 5:22 pm Post subject: |
|
|
djinnZ wrote: | Primo abilita hda-intel (in make.conf ALSA_CARDS) e prova anche ati/ali5xxx come device (sono fuori quindi non posso verificare in alcun modo).
Non è che c'è un jumper o una opzione nel bios per usare una uscita amplificata?
Per quanto riguarda i conflitti irq prova se succede qualcosa usando pci=routeirq etc.
Per fare una prima verifica all'acpi vedi [url]qui[/url]. Installa il compilatore (è in portage non ci vuole molto) e prova a ricompilare la dsdt. Se ti da errore puoi provare a fixarla altrimenti non ti fissare. |
l'opzione nel bios non credo che ci sia...
scusa l'ignoranza pci=routeirq dove lo piazzo ? su /etc/modules.d/alda ?
ho trovato un daemon chiamato irqbalance e lo metto ad avvio di default, o meglio di boot ?
secondo quello che scrive portage: irqbalance : Distribute hardware interrupts across processors on a multiprocessor system
non so cosa faccia di preciso ma non sembra funzionare.
Grazie per il link, se devo sistemare dsdt mi sa che impazzirò, sembra tanta roba e molto tecnica.
Ho visto che sono usciti un sacco di aggiornamenti del BIOS per la mia scheda madre (ASUS P5N-E SLI ho visto vari fix, magari succede qualcosa. _________________ si, sono noob... |
|
Back to top |
|
|
djinnZ Advocate
Joined: 02 Nov 2006 Posts: 4831 Location: somewhere in L.O.S.
|
Posted: Mon Jun 18, 2007 7:11 pm Post subject: |
|
|
opzione della linea di comando del kernel da inserire in lilo.conf od in grub.
Prima di aggiornare il bios fatti una copia e preparati a provarne diversi se vuoi provare a fixare la dsdt. Alcune volte gli aggiornamenti non fanno che rendere le cose ancora più ingarbugliate. Semmai fatti un giro su acpi.sf.net e vedi se qualche anima pia non ha già postato la dsdt coretta (facendo attenzione ad usarla con la corrispondente versione del bios) _________________ scita et risus abundant in ore stultorum sed etiam semper severi insani sunt
mala tempora currunt...mater stultorum semper pregna est
Murpy'sLaw:If anything can go wrong, it will - O'Toole's Corollary:Murphy was an optimist |
|
Back to top |
|
|
sirion n00b
Joined: 03 Jul 2005 Posts: 15
|
Posted: Mon Jun 18, 2007 10:24 pm Post subject: |
|
|
Ho iniziato a spulciare i wiki di Alsa e forse sto cominciando a vedere la luce alla fine del tunnel :
Sound can be heard but it is distorted:
*Some cards, notably SB Live! ones, suffer from distortion if the volume on some subchannels is higher than 66%. Some suffer distortion if the Master volume is higher than 66%, for some others the threshold is 50%. Reduce all volume setting. If the distortion goes away, experiment until you determine which are the highest volume settings that don't trigger distortion.
*Some cards, especially motherboard chipsets, have small limits on the fragment size (specified for example in the DMixPlugin configuration). Many cards cannot handle fragment sizes greater than 4096 bytes, and if it is bigger the fragment seems to be truncated and the sound becomes choppy.
*Some cards, especially recent ones, can only handle a fixed set of frequencies. Some can only handle a single frequency,usually 48000Hz. try to use the plug: plugin prefix when playing. If your card can only play a single fixed frequency you must ensure that the driver is told that (by the use of driver-specific option parameters), and the ALSA library is setup up to output sample only at that frequency. Usually this will involve using the plug plugin in /etc/asound.conf.
Credo che il mio caso sia l'ultimo, ovvero la frequenza fissa a 48000Hz, forse riesco a sistemare da configurazione. _________________ si, sono noob... |
|
Back to top |
|
|
sirion n00b
Joined: 03 Jul 2005 Posts: 15
|
Posted: Tue Jun 19, 2007 8:32 am Post subject: |
|
|
Ho provato a convertire le frequenze con mplayer:
ad esempio se lancio :
Code: |
mplayer -af rate=175000 file.mp3
|
il suono è molto meno distorto, e riesco a sentire quasi chiaramente il file mp3, anche se dell'interferenza rimane, forse devo sistemare anche la grandezza dei frammenti. Nel caso riesca a far andare il suono in maniera pulita posto il file di configurazione /etc/asound.conf. _________________ si, sono noob... |
|
Back to top |
|
|
!ico Apprentice
Joined: 26 Oct 2005 Posts: 199 Location: Bassano del Grappa (VI)
|
Posted: Tue Jun 19, 2007 9:41 am Post subject: |
|
|
io ho la tua stessa scheda madre e quindi anche la stessa scheda audio, e non ho riscontrato problemi.. sicuro che i tuoi mp3 siano a posto?
ola _________________ " I tasti iniziano. I tasti finiscono. Tu sai che sono 88; su questo nessuno può fregarti. Non sono infiniti loro. Tu, tu sei infinito, e dentro quei tasti, infinita è la musica che puoi fare. Loro sono 88. Tu sei infinito".
Novecento (Baricco) |
|
Back to top |
|
|
sirion n00b
Joined: 03 Jul 2005 Posts: 15
|
Posted: Tue Jun 19, 2007 10:47 am Post subject: |
|
|
!ico wrote: | io ho la tua stessa scheda madre e quindi anche la stessa scheda audio, e non ho riscontrato problemi.. sicuro che i tuoi mp3 siano a posto?
ola |
beh direi di si, ho provato anche un film in divx e fa la stessa cosa.
Se tu non hai problemi non è che mi mandi i un lsipci --v un dmesg, cat /proc/asound/cards, cat /proc/asound/card0/#codec, magari la configurazione del file /etc/modules.d/alsa ?
Se ti viene in mente qualcos'altro allega. _________________ si, sono noob... |
|
Back to top |
|
|
!ico Apprentice
Joined: 26 Oct 2005 Posts: 199 Location: Bassano del Grappa (VI)
|
Posted: Tue Jun 19, 2007 2:26 pm Post subject: |
|
|
Code: | ico@gentoo ~ $ cat /etc/modules.d/alsa
alias /dev/mixer snd-mixer-oss
alias /dev/dsp snd-pcm-oss
alias /dev/midi snd-seq-oss
alias char-major-116 snd
alias char-major-14 soundcore
alias sound-service-0-0 snd-mixer-oss
alias sound-service-0-1 snd-seq-oss
alias sound-service-0-3 snd-pcm-oss
alias sound-service-0-8 snd-seq-oss
alias sound-service-0-12 snd-pcm-oss
alias snd-card-0 snd-hda-intel
alias sound-slot-0 snd-hda-intel
|
Code: | ico@gentoo ~ $ cat /proc/asound/cards
0 [NVidia ]: HDA-Intel - HDA NVidia
HDA NVidia at 0xfe024000 irq 22
|
Code: |
ico@gentoo ~ $ cat /proc/asound/card0/codec#0
Codec: Analog Devices AD1986A
Address: 0
Vendor Id: 0x11d41986
Subsystem Id: 0x104381b3
Revision Id: 0x100500
Default PCM:
rates [0x7f]: 8000 11025 16000 22050 32000 44100 48000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Default Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Default Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=1
... e tutti i vari node che però sono tanti, non so se sia il caso.. |
dmesg non dice niente di particolare.
nel kernel ho solo CONFIG_SND_HDA_INTEL=m
e nel make.conf ho ALSA_CARDS="hda-intel", dopodichè ho emerso alsa-utils.[/code]
A meno di errori nella installazione non vedo dove possa essere il tuo problema..
ola _________________ " I tasti iniziano. I tasti finiscono. Tu sai che sono 88; su questo nessuno può fregarti. Non sono infiniti loro. Tu, tu sei infinito, e dentro quei tasti, infinita è la musica che puoi fare. Loro sono 88. Tu sei infinito".
Novecento (Baricco) |
|
Back to top |
|
|
djinnZ Advocate
Joined: 02 Nov 2006 Posts: 4831 Location: somewhere in L.O.S.
|
Posted: Tue Jun 19, 2007 4:08 pm Post subject: |
|
|
Potete postare entrambi le versioni del bios? Se sono diverse quella di !ico è quella giusta.
@sirion Mi viene a mente una cosa stupida, se sei su un pc ovviamente: prova prima a far funzionare il computer con l'alimentatore staccato dal case e prova anche a mettere la scheda audio in modo tale che la staffa metallica non tocchi il case. Se il rumore si attenua isolando l'alimentatore (cerca di non toccarlo mentre è sotto tensione) vuol dire che è da buttare, se invece isolando la staffa si riduce il rumore vuol dire che è uno degli altri componenti. _________________ scita et risus abundant in ore stultorum sed etiam semper severi insani sunt
mala tempora currunt...mater stultorum semper pregna est
Murpy'sLaw:If anything can go wrong, it will - O'Toole's Corollary:Murphy was an optimist |
|
Back to top |
|
|
sirion n00b
Joined: 03 Jul 2005 Posts: 15
|
Posted: Tue Jun 19, 2007 4:32 pm Post subject: |
|
|
!ico wrote: | Code: | ico@gentoo ~ $ cat /etc/modules.d/alsa
alias /dev/mixer snd-mixer-oss
alias /dev/dsp snd-pcm-oss
alias /dev/midi snd-seq-oss
alias char-major-116 snd
alias char-major-14 soundcore
alias sound-service-0-0 snd-mixer-oss
alias sound-service-0-1 snd-seq-oss
alias sound-service-0-3 snd-pcm-oss
alias sound-service-0-8 snd-seq-oss
alias sound-service-0-12 snd-pcm-oss
alias snd-card-0 snd-hda-intel
alias sound-slot-0 snd-hda-intel
|
|
La configurazione è simile...
!ico wrote: |
Code: | ico@gentoo ~ $ cat /proc/asound/cards
0 [NVidia ]: HDA-Intel - HDA NVidia
HDA NVidia at 0xfe024000 irq 22
|
|
anche con questo comando + o - ho le stesse cose
!ico wrote: |
Code: |
ico@gentoo ~ $ cat /proc/asound/card0/codec#0
Codec: Analog Devices AD1986A
Address: 0
Vendor Id: 0x11d41986
Subsystem Id: 0x104381b3
Revision Id: 0x100500
Default PCM:
rates [0x7f]: 8000 11025 16000 22050 32000 44100 48000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Default Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Default Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=1
... e tutti i vari node che però sono tanti, non so se sia il caso.. |
|
Qui ho le differenze maggiori... da me alsa usa un altro codec...
Code: |
Codec: Realtek ALC883
Address: 0
Vendor Id: 0x10ec0883
Subsystem Id: 0x10438249
Revision Id: 0x100002
Default PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
|
probabilmente perché a me dmesg mi da :
Code: |
hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
|
!ico wrote: |
nel kernel ho solo CONFIG_SND_HDA_INTEL=m
e nel make.conf ho ALSA_CARDS="hda-intel", dopodichè ho emerso alsa-utils.
A meno di errori nella installazione non vedo dove possa essere il tuo problema..
ola
|
Anche io ho la variabile ALSA_CARDS="hda-intel"
e ho alsa compilato come modulo.
Io ho una scheda madre ASUS P5N-E SLI con BIOS con versione 0602
Scheda audio : Realtek ALC883 6-channel CODEC _________________ si, sono noob... |
|
Back to top |
|
|
sirion n00b
Joined: 03 Jul 2005 Posts: 15
|
Posted: Tue Jun 19, 2007 4:36 pm Post subject: |
|
|
djinnZ wrote: | Potete postare entrambi le versioni del bios? Se sono diverse quella di !ico è quella giusta. |
Versione BIOS 0602 per Asus P5N-E SLI
djinnZ wrote: |
@sirion Mi viene a mente una cosa stupida, se sei su un pc ovviamente: prova prima a far funzionare il computer con l'alimentatore staccato dal case e prova anche a mettere la scheda audio in modo tale che la staffa metallica non tocchi il case. Se il rumore si attenua isolando l'alimentatore (cerca di non toccarlo mentre è sotto tensione) vuol dire che è da buttare, se invece isolando la staffa si riduce il rumore vuol dire che è uno degli altri componenti. |
In windows l'audio va senza problemi, scusate se non l'ho specificato, quindi non credo sia un problema di questo tipo, o sbaglio?
Inoltre il chip non è in una scheda audio ma integrato sulla MB. _________________ si, sono noob... |
|
Back to top |
|
|
sirion n00b
Joined: 03 Jul 2005 Posts: 15
|
Posted: Tue Jun 19, 2007 4:57 pm Post subject: |
|
|
Nuove notizie...
Ho scoperto che la mia scheda madre P5N-E SLI avendo un chip RealTek ALC883 che è di tipo Azalia può solo campionare a 196 KHz e 24 bit.
da wikipedia wrote: |
Azalia è il nome in codice utilizzato per definire l'"High Definiton Audio" sviluppato da Intel. Si tratta di un audio digitale di qualità superiore sul PC per un'esperienza surround-sound coinvolgente, riconoscimento vocale di qualità elevata e funzionalità Voice over IP, oltre a consentire la fruizione dell'audio Dolby dei PC. È stato introdotto con i chipset i925X e i915 per il Pentium 4 Prescott di ultima genererazione, e poi è stato implementato anche nelle rispettive evoluzioni i955X, i945 e i975X, per sostituire l'ormai obsoleto standard AC97. Supporta audio multicanale con campionamento a 196 KHz e 24 bit.
|
ecco un link ad una recensione della mia mobo:
http://www.phoronix.com/scan.php?page=article&item=727&num=1
Qui viene sbandierato che ho una scheda audio di tipo Azalia.
Quote: |
ASUS quality and innovations that enthusiasts have come to expect from their cutting edge products? Well, some of its many features include Intel Quad-Core support, NVIDIA SLI, and HD Azalia Audio.
|
Infatti quando variavo la frequenza di resample con mplayer quando mettevo 192000 il suono era quasi decente (prima ho dovuto mettere pci=noacpi come opzione su grub, thx djinnz).
Il problema è che mplayer mi faceva arrivare solo a 192000 e non a 196000hz.
Spero che con il plug plugin di alsa di poter arrivare a quella frequenza. _________________ si, sono noob... |
|
Back to top |
|
|
!ico Apprentice
Joined: 26 Oct 2005 Posts: 199 Location: Bassano del Grappa (VI)
|
Posted: Tue Jun 19, 2007 8:03 pm Post subject: |
|
|
sirion wrote: |
Versione BIOS 0602 per Asus P5N-E SLI
|
sono un idiota...
in realtà fino all'ultimo dovevo prendere quella ma poi ho preso un'altra e mi sono dimenticato del cambio...
per la cronaca comunque ho una asus m2npv-vm.
non ho una realtek, però lspci mi restituisce questo
Code: |
00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2) |
che mi sembrava simile al tuo...
vabbe, come non avessi detto niente, scusatemi..
ola _________________ " I tasti iniziano. I tasti finiscono. Tu sai che sono 88; su questo nessuno può fregarti. Non sono infiniti loro. Tu, tu sei infinito, e dentro quei tasti, infinita è la musica che puoi fare. Loro sono 88. Tu sei infinito".
Novecento (Baricco) |
|
Back to top |
|
|
sirion n00b
Joined: 03 Jul 2005 Posts: 15
|
Posted: Fri Jun 29, 2007 2:00 pm Post subject: |
|
|
Ho provato un paio di configurazioni del file /etc/asound.conf ma non sembra funzionare...
Forse perché sbaglio qualcosa nella configurazione... _________________ si, sono noob... |
|
Back to top |
|
|
sirion n00b
Joined: 03 Jul 2005 Posts: 15
|
Posted: Mon Oct 01, 2007 2:53 pm Post subject: |
|
|
Mi son accorto che il microfono va... ovvero sento perfettamente la mia voce dal microfono senza alcun disturbo.
Se invece cerco di ascoltare un qualsiasi suono ho un quintale di interferenze...
Potrebbe esserci un conflitto scheda audio/hard disk ? _________________ si, sono noob... |
|
Back to top |
|
|
Tigerwalk Guru
Joined: 15 May 2007 Posts: 475 Location: Napoli
|
Posted: Mon Oct 01, 2007 3:41 pm Post subject: |
|
|
credo che dovresti insistere nella ricerca dei codec per la tua scheda audio.
Da un'occhiata a questa discussione e, a siccome il link alla pagina dei moduli hda-intel non è più funzionante, te li posto sotto
Code: | Module snd-hda-intel
--------------------
Module for Intel HD Audio (ICH6, ICH6M, ESB2, ICH7, ICH8),
ATI SB450, SB600, RS600,
VIA VT8251/VT8237A,
SIS966, ULI M5461
model - force the model name
position_fix - Fix DMA pointer (0 = auto, 1 = none, 2 = POSBUF, 3 = FIFO size)
single_cmd - Use single immediate commands to communicate with
codecs (for debugging only)
enable_msi - Enable Message Signaled Interrupt (MSI) (default = off)
This module supports one card and autoprobe.
Each codec may have a model table for different configurations.
If your machine isn't listed there, the default (usually minimal)
configuration is set up. You can pass "model=<name>" option to
specify a certain model in such a case. There are different
models depending on the codec chip.
Model name Description
---------- -----------
ALC880
3stack 3-jack in back and a headphone out
3stack-digout 3-jack in back, a HP out and a SPDIF out
5stack 5-jack in back, 2-jack in front
5stack-digout 5-jack in back, 2-jack in front, a SPDIF out
6stack 6-jack in back, 2-jack in front
6stack-digout 6-jack with a SPDIF out
w810 3-jack
z71v 3-jack (HP shared SPDIF)
asus 3-jack (ASUS Mobo)
asus-w1v ASUS W1V
asus-dig ASUS with SPDIF out
asus-dig2 ASUS with SPDIF out (using GPIO2)
uniwill 3-jack
fujitsu Fujitsu Laptops (Pi1536)
F1734 2-jack
lg LG laptop (m1 express dual)
lg-lw LG LW20/LW25 laptop
tcl TCL S700
clevo Clevo laptops (m520G, m665n)
test for testing/debugging purpose, almost all controls can be
adjusted. Appearing only when compiled with
$CONFIG_SND_DEBUG=y
auto auto-config reading BIOS (default)
ALC260
hp HP machines
hp-3013 HP machines (3013-variant)
fujitsu Fujitsu S7020
acer Acer TravelMate
basic fixed pin assignment (old default model)
auto auto-config reading BIOS (default)
ALC262
fujitsu Fujitsu Laptop
hp-bpc HP xw4400/6400/8400/9400 laptops
hp-bpc-d7000 HP BPC D7000
benq Benq ED8
hippo Hippo (ATI) with jack detection, Sony UX-90s
hippo_1 Hippo (Benq) with jack detection
basic fixed pin assignment w/o SPDIF
auto auto-config reading BIOS (default)
ALC882/885
3stack-dig 3-jack with SPDIF I/O
6stack-dig 6-jack digital with SPDIF I/O
arima Arima W820Di1
macpro MacPro support
auto auto-config reading BIOS (default)
ALC883/888
3stack-dig 3-jack with SPDIF I/O
6stack-dig 6-jack digital with SPDIF I/O
3stack-6ch 3-jack 6-channel
3stack-6ch-dig 3-jack 6-channel with SPDIF I/O
6stack-dig-demo 6-jack digital for Intel demo board
acer Acer laptops (Travelmate 3012WTMi, Aspire 5600, etc)
medion Medion Laptops
targa-dig Targa/MSI
targa-2ch-dig Targs/MSI with 2-channel
laptop-eapd 3-jack with SPDIF I/O and EAPD (Clevo M540JE, M550JE)
auto auto-config reading BIOS (default)
ALC861/660
3stack 3-jack
3stack-dig 3-jack with SPDIF I/O
6stack-dig 6-jack with SPDIF I/O
3stack-660 3-jack (for ALC660)
uniwill-m31 Uniwill M31 laptop
toshiba Toshiba laptop support
asus Asus laptop support
asus-laptop ASUS F2/F3 laptops
auto auto-config reading BIOS (default)
ALC861VD/660VD
3stack 3-jack
3stack-dig 3-jack with SPDIF OUT
6stack-dig 6-jack with SPDIF OUT
3stack-660 3-jack (for ALC660VD)
auto auto-config reading BIOS (default)
CMI9880
minimal 3-jack in back
min_fp 3-jack in back, 2-jack in front
full 6-jack in back, 2-jack in front
full_dig 6-jack in back, 2-jack in front, SPDIF I/O
allout 5-jack in back, 2-jack in front, SPDIF out
auto auto-config reading BIOS (default)
AD1981
basic 3-jack (default)
hp HP nx6320
thinkpad Lenovo Thinkpad T60/X60/Z60
AD1986A
6stack 6-jack, separate surrounds (default)
3stack 3-stack, shared surrounds
laptop 2-channel only (FSC V2060, Samsung M50)
laptop-eapd 2-channel with EAPD (Samsung R65, ASUS A6J)
ultra 2-channel with EAPD (Samsung Ultra tablet PC)
AD1988
6stack 6-jack
6stack-dig ditto with SPDIF
3stack 3-jack
3stack-dig ditto with SPDIF
laptop 3-jack with hp-jack automute
laptop-dig ditto with SPDIF
auto auto-config reading BIOS (default)
Conexant 5045
laptop Laptop config
test for testing/debugging purpose, almost all controls
can be adjusted. Appearing only when compiled with
$CONFIG_SND_DEBUG=y
Conexant 5047
laptop Basic Laptop config
laptop-hp Laptop config for some HP models (subdevice 30A5)
laptop-eapd Laptop config with EAPD support
test for testing/debugging purpose, almost all controls
can be adjusted. Appearing only when compiled with
$CONFIG_SND_DEBUG=y
STAC9200/9205/9254
ref Reference board
STAC9220/9221
ref Reference board
3stack D945 3stack
5stack D945 5stack + SPDIF
macmini Intel Mac Mini
macbook Intel Mac Book
macbook-pro Intel Mac Book Pro
STAC9202/9250/9251
ref Reference board, base config
m2-2 Some Gateway MX series laptops
m6 Some Gateway NX series laptops
STAC9227/9228/9229/927x
ref Reference board
3stack D965 3stack
5stack D965 5stack + SPDIF
STAC9872
vaio Setup for VAIO FE550G/SZ110
vaio-ar Setup for VAIO AR
If the default configuration doesn't work and one of the above
matches with your device, report it together with the PCI
subsystem ID (output of "lspci -nv") to ALSA BTS or alsa-devel
ML (see the section "Links and Addresses").
Note 2: If you get click noises on output, try the module option
position_fix=1 or 2. position_fix=1 will use the SD_LPIB
register value without FIFO size correction as the current
DMA pointer. position_fix=2 will make the driver to use
the position buffer instead of reading SD_LPIB register.
(Usually SD_LPLIB register is more accurate than the
position buffer.)
NB: If you get many "azx_get_response timeout" messages at
loading, it's likely a problem of interrupts (e.g. ACPI irq
routing). Try to boot with options like "pci=noacpi". Also, you
can try "single_cmd=1" module option. This will switch the
communication method between HDA controller and codecs to the
single immediate commands instead of CORB/RIRB. Basically, the
single command mode is provided only for BIOS, and you won't get
unsolicited events, too. But, at least, this works independently
from the irq. Remember this is a last resort, and should be
avoided as much as possible...
The power-management is supported. |
|
|
Back to top |
|
|
sirion n00b
Joined: 03 Jul 2005 Posts: 15
|
Posted: Mon Oct 01, 2007 4:25 pm Post subject: |
|
|
Grazie per i nuovi docs, nella versione che avevo io mancano dei modelli.
La mia penso sia : "3stack-6ch-dig" 3-jack 6-channel with SPDIF I/O
Sul manuale della scheda madre Asus P5N-E SLI dice alla voce audio:
Realtek ALC883 6-channel CODEC
1 x Coaxial S/PDIF out port (dovrebbe essere la digitale, giusto ?)
Supports Audio Sensing and Enumeration technology
Supports Multi-Streaming Technology
Ho 3 jack sul retro e sembra sia 6 canali e ho un'uscita digitale quindi = 3stack-6ch-dig.
Ora mi funziona anche lo speaker, il beep arriva dalle casse e non + dallo speaker del pc.
Ma ancora non sento il suono mentre ascolto mp3 o guardo dei filmati...
grazie tigerwalk, hai altri suggerimenti ? _________________ si, sono noob... |
|
Back to top |
|
|
Tigerwalk Guru
Joined: 15 May 2007 Posts: 475 Location: Napoli
|
Posted: Mon Oct 01, 2007 5:27 pm Post subject: |
|
|
Si, ti consiglio di provare tutti i moduli della famiglia della tua scheda, perchè non sempre il modulo che dovrebbe essere quello idoneo, alla fine lavora come si deve! Devi, insomma, perdere qualche minuto di tempo! |
|
Back to top |
|
|
sirion n00b
Joined: 03 Jul 2005 Posts: 15
|
Posted: Mon Oct 01, 2007 9:28 pm Post subject: |
|
|
Ho provato anche gli altri ma sembra che la mia prima scelta sia la migliore... _________________ si, sono noob... |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|