View previous topic :: View next topic |
Author |
Message |
morellik l33t
Joined: 03 Feb 2003 Posts: 629 Location: Firenze
|
Posted: Mon May 19, 2003 5:51 pm Post subject: Plextor PX-S88TU CDR USB. HELP?? |
|
|
Dear all,
I have a Plextor PX-S88TU external USB CD Writer, but I'm unable
to use it.
I compile the kernel (vanilla 2.4.20) with usbcore, usb-storage and other USB driver support like module other than some SCSI driver.
When I connect the device with dmesg I see:
Code: |
# demsg
hub.c: new USB device 00:1d.0-2, assigned address 4
usb.c: USB device 4 (vend/prod 0x93b/0x0) is not claimed by any active driver.
|
At www.linux-usb.org I had see that this plextor is supported by usb driver
Quote: |
Details for: Plextor CD-R PX-S88T Status
( external CD-RW drive ) ( Category: Mass Storage )
ID 0x93b:0x0
Driver usb-storage
Linux-USB link
Vendor link http://www.plextor.be
Comment Works excellent (reading and writings CDs). Tested with Red Hat 7.2 kernel 2.7.4 (as it comes out of the box), a custom 2.4.16 and 2.4.18 kernel and XCDRoast. Even BurnProof gets activated. Just insert module usb-storage.
Submitted by info <at> ksjh.de
Submitted on Fri, 30 Nov 2001 00:17:25 +0100
Last edited on Mon, 1 Apr 2002 17:27:18 +0200
|
Please, how can I use this device under gentoo???
Thanks
morellik |
|
Back to top |
|
|
Yoshi Assim Apprentice
Joined: 16 Apr 2003 Posts: 234 Location: Girona (Spain)
|
Posted: Mon May 19, 2003 8:06 pm Post subject: |
|
|
Have installed hotplug package ?... |
|
Back to top |
|
|
morellik l33t
Joined: 03 Feb 2003 Posts: 629 Location: Firenze
|
Posted: Tue May 20, 2003 7:57 am Post subject: |
|
|
Before your post, no. Tomorrow I had install hotplug, but nothing happens.
I tried to connect/disconnect the device but I have the same messages:
Quote: |
usb.c: USB disconnect on device 00:1d.0-2 address 2
hub.c: new USB device 00:1d.0-2, assigned address 3
usb.c: USB device 3 (vend/prod 0x93b/0x0) is not claimed by any active driver.
usb.c: USB disconnect on device 00:1d.0-2 address 3
hub.c: new USB device 00:1d.0-1, assigned address 4
usb.c: USB device 4 (vend/prod 0x93b/0x0) is not claimed by any active driver.
|
morellik |
|
Back to top |
|
|
Yoshi Assim Apprentice
Joined: 16 Apr 2003 Posts: 234 Location: Girona (Spain)
|
Posted: Fri May 30, 2003 7:14 am Post subject: |
|
|
This drive is USB 2.0 compliant? If the answer is yes you must load/compile-in your kernel usb 2.0 module |
|
Back to top |
|
|
eik01 n00b
Joined: 19 May 2003 Posts: 31 Location: San Diego, CA USA
|
Posted: Fri May 30, 2003 9:56 am Post subject: |
|
|
does the cdrom apepar in /proc/scsi/usb-storage* folder? or in /proc/bus/usb? _________________ want some juice?! |
|
Back to top |
|
|
|