View previous topic :: View next topic |
Author |
Message |
fooblahblah n00b
![n00b n00b](/images/ranks/rank_rect_0.gif)
Joined: 10 Sep 2005 Posts: 8 Location: Boulder, CO
|
Posted: Tue Apr 18, 2006 11:08 pm Post subject: i945GM working for anyone? |
|
|
I've been struggling to get my Insprion 9400 with a i945GM chip to run using the i810 driver.
My PCI output reads:
Code: |
$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Expr
ess Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS/940GML Exp
ress Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/940GML Express In
tegrated Graphics Controller (rev 03)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Aud
io Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (r
ev 01)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (r
ev 01)
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (r
ev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev
01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev
01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev
01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev
01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Control
ler (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (re
v 01)
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA S
torage Controller IDE (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
03:01.1 Class 0805: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 1
9)
03:01.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
03:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (re
v 0a)
03:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05)
0c:00.0 Network controller: Broadcom Corporation Unknown device 4311 (rev 01)
|
I'm running gentoo-sources-2.6.16-r2 with AGP and Intel support compiled into the kernel (not using kernel DRM support). I've installed modular Xorg-7 and vesa works, but not i810. I've also installed the libdrm, mesa and drm (compiled for i810 and i910) from the Freedesktop CVS repository, but I get the same output "No devices detected".
I can post more info, but I was mainly curious if anyone with an Inspiron 9400 with the same lspci output has X running using the i810 driver? |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
ynema n00b
![n00b n00b](/images/ranks/rank_rect_0.gif)
Joined: 11 Apr 2005 Posts: 13 Location: Perth, Western Australia
|
Posted: Wed Apr 19, 2006 9:26 am Post subject: ipw3946ABG |
|
|
Cheers for some of the info in this thread some of it applies to my Asus A6J as it appears to have similar hardware and I can't find much on that laptop specifically.
But anyway people may be interested to know that the ipw3945 drivers are in portage
emerge ipw3945 should emerge ipw3945, ipw3945d and ipw3945-ucode packages they do appear to still be masked but they worked straight up on my system |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
VinzC Watchman
![Watchman Watchman](/images/ranks/rank-G-2-watchman.gif)
![](images/avatars/92679028148bc3f0ff1e99.jpg)
Joined: 17 Apr 2004 Posts: 5098 Location: Dark side of the mood
|
Posted: Wed Apr 19, 2006 9:46 am Post subject: Re: ipw3946ABG |
|
|
ynema wrote: | But anyway people may be interested to know that the ipw3945 drivers are in portage |
Right, I forgot to put a reference to my post in the ipw3945 thread . _________________ Gentoo addict: tomorrow I quit, I promise!... Just one more emerge...
1739! |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
Sejam Tux's lil' helper
![Tux's lil' helper Tux's lil' helper](/images/ranks/rank_rect_1.gif)
Joined: 25 Oct 2004 Posts: 80
|
Posted: Thu Apr 20, 2006 4:14 am Post subject: Re: i945GM working for anyone? |
|
|
fooblahblah wrote: | I've been struggling to get my Insprion 9400 with a i945GM chip to run using the i810 driver.
My PCI output reads:
I'm running gentoo-sources-2.6.16-r2 with AGP and Intel support compiled into the kernel (not using kernel DRM support). I've installed modular Xorg-7 and vesa works, but not i810. I've also installed the libdrm, mesa and drm (compiled for i810 and i910) from the Freedesktop CVS repository, but I get the same output "No devices detected".
I can post more info, but I was mainly curious if anyone with an Inspiron 9400 with the same lspci output has X running using the i810 driver? |
Are you sure that there have been drivers written for the i945GM yet? I remember when we got the i915, it took about 4 months for us to be able to use it in anything else besides vesa. You might try some of the tricks we had to do early on for the Inspiron 6000 (with the i915) to get it working. I know I've seen an updated 915resolution program that will probably help. |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
fooblahblah n00b
![n00b n00b](/images/ranks/rank_rect_0.gif)
Joined: 10 Sep 2005 Posts: 8 Location: Boulder, CO
|
Posted: Thu Apr 20, 2006 12:04 pm Post subject: Re: i945GM working for anyone? Yes me! |
|
|
I managed to get this working. It's still a but fuzzy as to what combination of packages solved it.
I had given up on xorg-6.9.0 and moved to xorg-7 (a.k.a. modular xorg) and had the thing running in vesa mode. The final key was to have 'xorg-server' and 'xf86-video-i810' in *both* my /etc/portage/package.keywords and package.unmask. After re-emerging those packages my xorg config using i810 driver successfully started and detected the device.
I'm now getting ~1500fps with glxgears.
I've also run the 855resolution hack to 1440x900 resolution. Here's what I'm using in my /etc/conf.d/855resolution:
Code: |
replace[0]="4d"
with[0]="1440 900"
|
The one thing that's less than ideal is that I'm only running in 16bit mode. When I use 855resolution -l there are no 24bit modes listed... |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
saintpa Tux's lil' helper
![Tux's lil' helper Tux's lil' helper](/images/ranks/rank_rect_1.gif)
![](images/avatars/gallery/Futurama/cartoon_futurama_bender.gif)
Joined: 04 Dec 2004 Posts: 77
|
Posted: Fri Apr 28, 2006 9:44 pm Post subject: Re: i945GM working for anyone? |
|
|
Sejam wrote: |
Are you sure that there have been drivers written for the i945GM yet? I remember when we got the i915, it took about 4 months for us to be able to use it in anything else besides vesa. You might try some of the tricks we had to do early on for the Inspiron 6000 (with the i915) to get it working. I know I've seen an updated 915resolution program that will probably help. |
The i915 driver works for 945GM (A.K.A. GMA950), but you need the latest drm kernel driver from cvs tree. It works for me. |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
kurtg Tux's lil' helper
![Tux's lil' helper Tux's lil' helper](/images/ranks/rank_rect_1.gif)
![](images/avatars/891678747432823bfabf3a.gif)
Joined: 13 Sep 2005 Posts: 103 Location: Florida USA
|
Posted: Tue May 02, 2006 8:13 pm Post subject: |
|
|
Any joy with the Intel 945GM Graphics card. It looks like a great chipset, but I can't seem to find much information on them for Linux. |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
kurtg Tux's lil' helper
![Tux's lil' helper Tux's lil' helper](/images/ranks/rank_rect_1.gif)
![](images/avatars/891678747432823bfabf3a.gif)
Joined: 13 Sep 2005 Posts: 103 Location: Florida USA
|
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
saintpa Tux's lil' helper
![Tux's lil' helper Tux's lil' helper](/images/ranks/rank_rect_1.gif)
![](images/avatars/gallery/Futurama/cartoon_futurama_bender.gif)
Joined: 04 Dec 2004 Posts: 77
|
Posted: Wed May 03, 2006 2:54 am Post subject: |
|
|
945GM works. I have a dell inspiron 6400 and it works great. I get around 1300fps with glxgears. I didn't use the intel driver, though. |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
kurtg Tux's lil' helper
![Tux's lil' helper Tux's lil' helper](/images/ranks/rank_rect_1.gif)
![](images/avatars/891678747432823bfabf3a.gif)
Joined: 13 Sep 2005 Posts: 103 Location: Florida USA
|
Posted: Wed May 03, 2006 12:15 pm Post subject: Re: i945GM working for anyone? |
|
|
saintpa wrote: |
The i915 driver works for 945GM (A.K.A. GMA950), but you need the latest drm kernel driver from cvs tree. It works for me. |
Could you point a newbie in the right direction? Which CVS tree? |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
LD Guru
![Guru Guru](/images/ranks/rank_rect_3.gif)
![](images/avatars/164215002846c9245d0cde6.png)
Joined: 23 Dec 2003 Posts: 336 Location: Middle of No-Where Granbury, Tx
|
Posted: Sun May 07, 2006 3:43 am Post subject: |
|
|
I have almost everything working. A coule of questions though:
1. What should I do for the dial up modem
2. Has anyone figured out the TV-Out put yet? If so let me know or point me in the right direction. I have an intel 915 on mine.
3. Same as the fellow above me about the newest X modules for the i915 chipset driver. Any joy there? _________________ [Owner/Operator: Dhampir Dreams]
Last.fm profile
Netflix Profile |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
broeisi n00b
![n00b n00b](/images/ranks/rank_rect_0.gif)
Joined: 08 Mar 2003 Posts: 7
|
Posted: Sun May 07, 2006 10:15 pm Post subject: |
|
|
saintpa..
how did you get those 1300 fps with the i945?
could you post what you did? |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
saintpa Tux's lil' helper
![Tux's lil' helper Tux's lil' helper](/images/ranks/rank_rect_1.gif)
![](images/avatars/gallery/Futurama/cartoon_futurama_bender.gif)
Joined: 04 Dec 2004 Posts: 77
|
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
dob Apprentice
![Apprentice Apprentice](/images/ranks/rank_rect_2.gif)
![](images/avatars/19655642823ec793c46ee56.png)
Joined: 04 Oct 2002 Posts: 199 Location: S.L.P.
|
Posted: Wed May 10, 2006 5:29 pm Post subject: |
|
|
Quote: | Hard Disk and CD/DVD Writer
Unlike what is mentionned on Dell's web site, the hard disk is IDE and not a SATA. (The conspiracy theory, you know ) In fact the hard disk is an IDE one that is plugged onto a SATA/IDE bridge. Here are the kernel options I selected in Device Drivers > ATA/ATAPI/MFM/RLL support:
Code: | < > ATA/ATAPI/MFM/RLL support |
|
You might want to precise than the libata.atapi_enabled=1 option has to be passed to the boot loader for the ide burner to be recognized
I only burned 1 dvd so far, and it was extremely slow (like 1x). I don't what else to try.
Quote: | CPU speed control
I've reused my Dell i6k CPU frequency scaling. Here's my related kernel config in Power management options (ACPI, APM) > CPU Frequency scaling:
Code: | [*] CPU Frequency scaling |
|
Or the kernel's on demand governor can be used (no need for a userspace daemon)
Just add the following to /etc/conf.d/local.start
Code: | echo -n ondemand > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
echo -n ondemand > /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor |
You can see the temperature with cat /proc/acpi/thermal_zone/THM/temperature (or gkrellm can display it on your desktop) |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
VinzC Watchman
![Watchman Watchman](/images/ranks/rank-G-2-watchman.gif)
![](images/avatars/92679028148bc3f0ff1e99.jpg)
Joined: 17 Apr 2004 Posts: 5098 Location: Dark side of the mood
|
Posted: Thu May 11, 2006 7:29 am Post subject: |
|
|
dob wrote: | You might want to precise than the libata.atapi_enabled=1 option has to be passed to the boot loader for the ide burner to be recognized. |
You don't need libata.atapi_enabled=1 kernel argument anymore with kernels 2.6.16.
dob wrote: | Or the kernel's on demand governor can be used (no need for a userspace daemon)
Just add the following to /etc/conf.d/local.start
Code: | echo -n ondemand > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
echo -n ondemand > /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor |
|
That's good to know. I set mine with kernel's defaults, performance. Do you think the ondemand governor increases battery lifetime significantly? _________________ Gentoo addict: tomorrow I quit, I promise!... Just one more emerge...
1739! |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
LD Guru
![Guru Guru](/images/ranks/rank_rect_3.gif)
![](images/avatars/164215002846c9245d0cde6.png)
Joined: 23 Dec 2003 Posts: 336 Location: Middle of No-Where Granbury, Tx
|
Posted: Thu May 11, 2006 10:25 pm Post subject: |
|
|
I found a proprietary driver from intel for the 945GM chipset here.
Now, I have no idea what to do to make this a working ebuild or what.
If someone does though please feel free to make one for this driver. I'll install it from scratch and see what I end up with. _________________ [Owner/Operator: Dhampir Dreams]
Last.fm profile
Netflix Profile |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
seppelrockt Guru
![Guru Guru](/images/ranks/rank_rect_3.gif)
Joined: 14 May 2004 Posts: 423
|
Posted: Fri May 12, 2006 12:48 pm Post subject: |
|
|
Noven wrote: |
While I was doing this I also set up all the multimedia keys. They all had a keycode already assigned, so I just had to set up a .Xmodmap and then bind the keys in e16keyedit. Here is mine:
Code: |
$ cat .Xmodmap
keycode 160 = XF86AudioMute
keycode 174 = XF86AudioLowerVolume
keycode 176 = XF86AudioRaiseVolume
keycode 162 = XF86AudioPlay
keycode 144 = XF86AudioPrev
keycode 153 = XF86AudioNext
keycode 164 = XF86AudioStop
$ cat .e16/e_config.bindings
<snip>
KeyDown C e exec Eterm
KeyDown - XF86AudioLowerVolume exec amixer sset PCM 4-
KeyDown - XF86AudioRaiseVolume exec amixer sset PCM 4+
KeyDown - XF86AudioMute exec amixer sset Master toggle
|
|
Sorry for highjacking this thread but I try to do the same Xmodmap magic for my Dell I6000. I have a correct .Xmodmap file in /home but I don't know whether/where I have to tell X/KDE about this file? So how can I "apply" the Xmodmap file when X/KDE get's started? |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
dob Apprentice
![Apprentice Apprentice](/images/ranks/rank_rect_2.gif)
![](images/avatars/19655642823ec793c46ee56.png)
Joined: 04 Oct 2002 Posts: 199 Location: S.L.P.
|
Posted: Sat May 13, 2006 5:21 am Post subject: |
|
|
VinzC wrote: | dob wrote: | Or the kernel's on demand governor can be used (no need for a userspace daemon)
Just add the following to /etc/conf.d/local.start
Code: | echo -n ondemand > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
echo -n ondemand > /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor |
|
That's good to know. I set mine with kernel's defaults, performance. Do you think the ondemand governor increases battery lifetime significantly? |
I think it should, and I don't see any reason not to use it. The cpu run automatically at full speed when needed, and at 1Ghz otherwise
Code: |
model name : Genuine Intel(R) CPU T2400 @ 1.83GHz
stepping : 8
cpu MHz : 1000.000 |
Last edited by dob on Sat May 13, 2006 5:30 am; edited 2 times in total |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
dob Apprentice
![Apprentice Apprentice](/images/ranks/rank_rect_2.gif)
![](images/avatars/19655642823ec793c46ee56.png)
Joined: 04 Oct 2002 Posts: 199 Location: S.L.P.
|
Posted: Sat May 13, 2006 5:27 am Post subject: |
|
|
Noven wrote: |
While I was doing this I also set up all the multimedia keys. They all had a keycode already assigned, so I just had to set up a .Xmodmap and then bind the keys in e16keyedit. Here is mine:
Sorry for highjacking this thread but I try to do the same Xmodmap magic for my Dell I6000. I have a correct .Xmodmap file in /home but I don't know whether/where I have to tell X/KDE about this file? So how can I "apply" the Xmodmap file when X/KDE get's started? | Why not use lineakd?
There are some instructions there
And their proposed lineakd.conf can easily be improved
Quote: | Lineak
http://lineak.sourceforge.net/
Run lineakd -c DELLI-9200 as a normal user and a ~/.lineak/lineakd.conf file will be created.
open that file in a editor
nano ~/.lineak/lineakd.conf
And change the following lines at the end of the file
Mute =
Next =
Play|Pause =
Previous =
Stop =
VolumeDown =
VolumeUp =
to
Mute =
Next =
Play|Pause = xmms --play-pause
Previous =
Stop = xmms --stop
VolumeDown = amixer -c 0 set Master 5%-
VolumeUp = amixer -c 0 set Master 5%+ |
|
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
VinzC Watchman
![Watchman Watchman](/images/ranks/rank-G-2-watchman.gif)
![](images/avatars/92679028148bc3f0ff1e99.jpg)
Joined: 17 Apr 2004 Posts: 5098 Location: Dark side of the mood
|
Posted: Sat May 13, 2006 9:57 am Post subject: |
|
|
I saw KDE and Gnome both already supported the volume mute, up and down keys with a nice On-Screen Display indication. I don't know however what to do to enable it. Wouldn't lineakd disable both desktops OSD? _________________ Gentoo addict: tomorrow I quit, I promise!... Just one more emerge...
1739! |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
dob Apprentice
![Apprentice Apprentice](/images/ranks/rank_rect_2.gif)
![](images/avatars/19655642823ec793c46ee56.png)
Joined: 04 Oct 2002 Posts: 199 Location: S.L.P.
|
Posted: Sat May 13, 2006 5:28 pm Post subject: |
|
|
VinzC wrote: | I saw KDE and Gnome both already supported the volume mute, up and down keys with a nice On-Screen Display indication. I don't know however what to do to enable it. Wouldn't lineakd disable both desktops OSD? | It doesn't work for me (kde)! Is it enabled in Regional & Accessibility / Input actions in kde's control center?
I can't find where to set it up, and yes I have khotkeys installed (part of kdebase)
Quote: | You don't need libata.atapi_enabled=1 kernel argument anymore with kernels 2.6.16. |
Could you please elaborate on this?
I'm currently using vanilla 2.6.16.2 and I can't find my dvd drive without enabling support for atapi devices in the kernel or using the libata.atapi_enabled=1 boot option |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
VinzC Watchman
![Watchman Watchman](/images/ranks/rank-G-2-watchman.gif)
![](images/avatars/92679028148bc3f0ff1e99.jpg)
Joined: 17 Apr 2004 Posts: 5098 Location: Dark side of the mood
|
Posted: Sat May 13, 2006 5:33 pm Post subject: |
|
|
dob wrote: | Could you please elaborate on this?
I'm currently using vanilla 2.6.16.2 and I can't find my dvd drive without enabling support for atapi devices in the kernel or using the libata.atapi_enabled=1 boot option |
Well, just like I said I didn't need to pass that argument to my kernel. I'm using Gentoo Sources 2.6.16 series, patched for SD card reader only and the CD/DVD drive works right out of the box for me. _________________ Gentoo addict: tomorrow I quit, I promise!... Just one more emerge...
1739! |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
kurtg Tux's lil' helper
![Tux's lil' helper Tux's lil' helper](/images/ranks/rank_rect_1.gif)
![](images/avatars/891678747432823bfabf3a.gif)
Joined: 13 Sep 2005 Posts: 103 Location: Florida USA
|
Posted: Mon May 15, 2006 3:32 pm Post subject: |
|
|
When I close the lid, I can't seem to get the back light to come back on.
I finally have my Insprion 9400 with a i945GM with Xorg/Gnome running fine. So far, I need to ssh in from another box, and reboot the laptop to get the backlight back on again.
These seems to be true for both character and X11 displays, so I think this is a BIOS switch that turns it off, but then is expecting software to turn it back on again.
Anybody else deal with issue? Solve it? |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
seppelrockt Guru
![Guru Guru](/images/ranks/rank_rect_3.gif)
Joined: 14 May 2004 Posts: 423
|
Posted: Mon May 15, 2006 5:33 pm Post subject: |
|
|
kurtg wrote: | When I close the lid, I can't seem to get the back light to come back on.
I finally have my Insprion 9400 with a i945GM with Xorg/Gnome running fine. So far, I need to ssh in from another box, and reboot the laptop to get the backlight back on again.
These seems to be true for both character and X11 displays, so I think this is a BIOS switch that turns it off, but then is expecting software to turn it back on again.
Anybody else deal with issue? Solve it? |
Looks like the I9400 has the same ACPI bug as the I6000.
To get the backlight on you can emerge vbetool and type
in a console (blind). You can put this comment somewere in the scripts that deal with ACPI events to call it automatically when you open the LID - the solution can be found somewere in the Dell Inspiron 6000 Thread in the forum. |
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
saintpa Tux's lil' helper
![Tux's lil' helper Tux's lil' helper](/images/ranks/rank_rect_1.gif)
![](images/avatars/gallery/Futurama/cartoon_futurama_bender.gif)
Joined: 04 Dec 2004 Posts: 77
|
|
Back to top |
|
![](templates/gentoo/images/spacer.gif) |
|