Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
Xfree + Nvidia DVI probleem
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Dutch
View previous topic :: View next topic  
Author Message
ParoXysm
n00b
n00b


Joined: 01 Sep 2002
Posts: 10
Location: RoseValley

PostPosted: Tue Nov 05, 2002 6:04 pm    Post subject: Xfree + Nvidia DVI probleem Reply with quote

Heej Gentoovrinden,

Ik heb Gentoo 1.2 draaien en net ff snel Xfree en Fluxbox gemerged.
Maar nu zit ik met het volgende probleem.

Ik heb een Asus Geforce4 TI 4200 met DVI en Analoge aansluiting, op de DVI een Neovo X174 Flatpanel en op de analoge een oude 17"inch CRT.
Als ik nu startx doe krijg ik fluxbox te zien op mijn CRT monitor, en mijn TFT begint te ijlen dat hij geen input krijgt.

Nu heb ik al alle Nvidia options aan mijn XF86Config toegevoegd, maar het beeld blijft alleen maar op mijn CRT komen. Dus blijkbaar ziet Xfree de CRT als primary display. Maar ook als ik Twinview dus aanzet en het volgende opgeef:

Option "ConnectedMonitor" "CRT, DFP"

dan doet tie niets...
Dus mijn vraag, hoe vertel ik Xfree dat hij het beeld moet weergeven op de DVI?
Back to top
View user's profile Send private message
ParoXysm
n00b
n00b


Joined: 01 Sep 2002
Posts: 10
Location: RoseValley

PostPosted: Tue Nov 05, 2002 9:39 pm    Post subject: Reply with quote

Nevermind, alleen DFP invullen doet het nu opeens wel, krijg nu netjes beeld op mijn TFT.

Echter als ik via ctrl+alt+f2 een console wil openen krijg ik nog wel een no signal melding. Misschien dat dit samenhangt aangezien ik vesafb gebruik voor console.
Back to top
View user's profile Send private message
ParoXysm
n00b
n00b


Joined: 01 Sep 2002
Posts: 10
Location: RoseValley

PostPosted: Wed Nov 20, 2002 4:59 pm    Post subject: Reply with quote

vesafb uitzetten maakt dus geen flikker uit...als ik gentoo opstart, no problems, ga ik naar X, no problems netjes beeld, sluit ik X af of wil ik switchen naar console, dan signal lost, beeld ook niet terug te krijgen op een reboot na dan...snap er niets van, zelfs op mijn 2de CRT monitor is het signaal verloren. Anyone???
Back to top
View user's profile Send private message
SeJo
Retired Dev
Retired Dev


Joined: 08 Oct 2002
Posts: 298
Location: Belgium

PostPosted: Thu Nov 21, 2002 7:38 am    Post subject: Reply with quote

als je gewoon opstart in console mode wat zie je dan?
komen dan je beide schermen op of niet?
Wat ergens logisch is als je in Xfree je twee schermen definieert, dat ie eens je Xfree afsluit dat 1 no signal krijgt. wel raar dat ze beide stoppen.

Eerst en vooral dus, als je opstart met de console wat krijg je dan?
Back to top
View user's profile Send private message
ParoXysm
n00b
n00b


Joined: 01 Sep 2002
Posts: 10
Location: RoseValley

PostPosted: Thu Nov 21, 2002 3:33 pm    Post subject: Reply with quote

ff Nvidia-meuk opnieuw gecompiled en nu is de situatie zo:

Ik start zowiezo op in console, en heb op zowel TFT als CRT beeld.
ik typ startx en ga netjes naar fluxbox, maar is het signaal op de CRT lost.
Als ik dan ctrl+alt+f2 doe is het signaal op de TFT lost, maar op mijn CRT
krijg ik netjes mijn console te zien.
Via ctrl+alt+f7 kan ik op mijn TFT weer terugswitchen naar X.

Dat mijn CRT het niet doet in X kan kloppen, aangezien ik alleen nog maar DFP heb opgegeven bij de Nvidia options, en nog geen twinview clone meuk. Maar dat hij bij het afsluiten van X of switchen naar console niet teruggaat naar mijn DVI snap ik niet.
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Dutch All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum