| View previous topic :: View next topic |
| Author |
Message |
flowolf
Tux's lil' helper
Joined: 22 Jun 2003
Posts: 143
|
 Posted: Sun Jun 20, 2004 1:30 am Post subject: [KERNEL] 2.6.7 e le periferiche perdute... [AGGIRATO] |
 |
|
Oggi ho aggiornato il mio gentoo-dev-sources dalla versione 2.6.5-r1 alla 2.6.7 e mi sono ritrovato con diverse periferiche completamente paralizzate:
1) La scheda di rete nforce viene riconosciuta, attivata ed impostata tuttavia non ha alcuna comunicazione con la mia LAN.
2) La scheda audio nforce viene riconosciuta, attivata e viene creato /dev/dsp tuttavia non produce alcun suono.
3) La scheda DVB viene riconosciuta e vengono creati gli appositi device in /dev/dvb/ ma ancora una volta non ne funziona neanche uno...
Questo è il mio dmesg:
| Code: | 00000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126960 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
Asus A7N8X v2 detected: BIOS IRQ0 pin2 override will be ignored
ACPI: RSDP (v000 Nvidia ) @ 0x000f75e0
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff74c0
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
Built 1 zonelists
Kernel command line: BOOT_IMAGE=Gentoo ro root=343 video=vesa:ywrap,mtrr
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 2204.847 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Memory: 514408k/524224k available (3393k kernel code, 9052k reserved, 1102k data, 168k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4358.14 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 3200+ stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb490, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: nForce2 C1 Halt Disconnect fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB1._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17)
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19)
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23)
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt Link [LSMB] enabled at IRQ 11
ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 5
ACPI: PCI Interrupt Link [LUBB] enabled at IRQ 5
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 11
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 11
ACPI: PCI Interrupt Link [LAPU] enabled at IRQ 5
ACPI: PCI Interrupt Link [LACI] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 11
ACPI: PCI Interrupt Link [L3CM] enabled at IRQ 5
ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 5
PCI: Using ACPI for IRQ routing
vesafb: framebuffer at 0xd0000000, mapped to 0xe0808000, size 5120k
vesafb: mode is 1280x1024x16, linelength=2560, pages=1
vesafb: protected mode interface info at c000:f510
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
fb0: VESA VGA frame buffer device
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.14 [Flags: R/O].
udf: registering filesystem
SGI XFS with no debug enabled
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1)
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
Console: switching to colour frame buffer device 160x64
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 256M @ 0xc0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 (0x778) [PCSPP(,...)]
parport0: irq 7 detected
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:01.0: 3Com PCI 3c920 Tornado at 0xd000. Vers LK1.1.19
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.25.
PCI: Setting latency timer of device 0000:00:04.0 to 64
eth1: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:04.0
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
Linux video capture interface: v1.00
drivers/media/dvb/b2c2/skystar2.c: FlexCopII(rev.130) chip found
drivers/media/dvb/b2c2/skystar2.c: the chip has 6 hardware filters
DVB: registering new adapter (Technisat SkyStar2 driver).
DVB: registering frontend 0:0 (Zarlink MT312)...
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 6Y120L0, ATA DISK drive
hdb: IC35L030AVV207-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: PIONEER DVD-RW DVR-106D, ATAPI CD/DVD-ROM drive
hdd: HL-DT-STDVD-ROM GDR8161B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 240121728 sectors (122942 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 > p3 p4
hdb: max request size: 1024KiB
hdb: 60036480 sectors (30738 MB) w/1821KiB Cache, CHS=16383/255/63, UDMA(100)
/dev/ide/host0/bus0/target1/lun0: p1 p2 p3
hdc: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 11, pci mem e0e9e000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
irq 11: nobody cared!
[<c01063ee>] dump_stack+0x1e/0x20
[<c010779b>] __report_bad_irq+0x2b/0x90
[<c0107894>] note_interrupt+0x64/0xa0
[<c0107b2f>] do_IRQ+0x12f/0x140
[<c0105fdc>] common_interrupt+0x18/0x20
[<c011a23c>] do_softirq+0x2c/0x30
[<c0107b09>] do_IRQ+0x109/0x140
[<c0105fdc>] common_interrupt+0x18/0x20
[<c037e4f9>] ehci_start+0x2d9/0x370
[<c0374d03>] usb_hcd_pci_probe+0x2a3/0x4e0
[<c02a695b>] pci_device_probe_static+0x4b/0x60
[<c02a69a6>] __pci_device_probe+0x36/0x50
[<c02a69ec>] pci_device_probe+0x2c/0x50
[<c02f723d>] bus_match+0x3d/0x70
[<c02f736a>] driver_attach+0x5a/0x90
[<c02f7661>] bus_add_driver+0xa1/0xc0
[<c02f7b11>] driver_register+0x31/0x40
[<c02a6c3b>] pci_register_driver+0x5b/0x80
[<c057efa5>] init+0x25/0x30
[<c05686ac>] do_initcalls+0x2c/0xc0
[<c0100458>] init+0x38/0x160
[<c01040f1>] kernel_thread_helper+0x5/0x14
handlers:
[<c03303f0>] (isr+0x0/0xc0)
[<c0370bf0>] (usb_hcd_irq+0x0/0x70)
Disabling IRQ #11
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ohci_hcd 0000:00:02.0: nVidia Corporation nForce2 USB Controller
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 5, pci mem e0ea0000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0000:00:02.1: nVidia Corporation nForce2 USB Controller (#2)
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 5, pci mem e0ea2000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
USB Universal Host Controller Interface driver v2.2
usbcore: registered new driver cdc_acm
drivers/usb/class/cdc-acm.c: v0.23:USB Abstract Control Model driver for USB modems and ISDN adapters
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usbcore: registered new driver ov511
drivers/usb/media/ov511.c: v1.64 for Linux 2.5 : ov511 USB Camera Driver
usbcore: registered new driver usbnet
Advanced Linux Sound Architecture Driver Version 1.0.4 (Mon May 17 14:31:44 2004 UTC).
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 49389 usecs
intel8x0: clocking to 47414
ohci_hcd 0000:00:02.0: remote wakeup
ALSA device list:
#0: NVidia nForce2 at 0xdd080000, irq 11
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 296 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET: Registered protocol family 1
NET: Registered protocol family 17
ReiserFS: hdb3: found reiserfs format "3.6" with standard journal
usb 2-2: new full speed USB device using address 2
ReiserFS: hdb3: using ordered data mode
ReiserFS: hdb3: journal params: device hdb3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdb3: checking transaction log (hdb3)
ReiserFS: hdb3: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 168k freed
Adding 498004k swap on /dev/hdb2. Priority:-1 extents:1
ReiserFS: hda4: found reiserfs format "3.6" with standard journal
ReiserFS: hda4: using ordered data mode
ReiserFS: hda4: journal params: device hda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda4: checking transaction log (hda4)
ReiserFS: hda4: Using r5 hash to sort names
Unable to load NLS charset cp437
Unable to load NLS charset iso8859-1
Unable to load NLS charset iso8859-1
nvidia: module license 'NVIDIA' taints kernel.
0: nvidia: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-5336 Wed Jan 14 18:29:26 PST 2004
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:03:00.0 into 8x mode
dvb_net_feed_start: rx_mode 0
dvb_net_feed_start: alloc secfeed
dvb_net_feed_start: set secfilter
dvb0_0: filter mac=00 00 00 00 00 00
dvb0_0: filter mask=ff ff ff ff ff ff
dvb_net_feed_start: start filtering
dvb_net_feed_stop
dvb_net_feed_stop: stop secfeed
dvb_net_feed_stop: release secfilter
dvb_net_feed_start: rx_mode 0
dvb_net_feed_start: alloc secfeed
dvb_net_feed_start: set secfilter
dvb0_0: filter mac=00 00 00 00 00 00
dvb0_0: filter mask=ff ff ff ff ff ff
dvb_net_feed_start: start filtering
dvb_net_feed_stop
dvb_net_feed_stop: stop secfeed
dvb_net_feed_stop: release secfilter
dvb0_0: set_mc_list, 1 entries
dvb_net_feed_start: rx_mode 1
dvb_net_feed_start: alloc secfeed
dvb_net_feed_start: set secfilter
dvb0_0: filter mac=00 00 00 00 00 00
dvb0_0: filter mask=ff ff ff ff ff ff
dvb_net_feed_start: set multi_secfilter[0]
dvb0_0: filter mac=01 00 5e 00 00 01
dvb0_0: filter mask=ff ff ff ff ff ff
dvb_net_feed_start: start filtering
dvb_net_feed_stop
dvb_net_feed_stop: stop secfeed
dvb_net_feed_stop: release secfilter
dvb_net_feed_stop: release multi_filter[0]
dvb0_0: set_mc_list, 1 entries
dvb_net_feed_start: rx_mode 1
dvb_net_feed_start: alloc secfeed
dvb_net_feed_start: set secfilter
dvb0_0: filter mac=00 00 00 00 00 00
dvb0_0: filter mask=ff ff ff ff ff ff
dvb_net_feed_start: set multi_secfilter[0]
dvb0_0: filter mac=01 00 5e 00 00 01
dvb0_0: filter mask=ff ff ff ff ff ff
dvb_net_feed_start: start filtering
dvb_net_feed_stop
dvb_net_feed_stop: stop secfeed
dvb_net_feed_stop: release secfilter
dvb_net_feed_stop: release multi_filter[0]
dvb_net_feed_start: rx_mode 1
dvb_net_feed_start: alloc secfeed
dvb_net_feed_start: set secfilter
dvb0_0: filter mac=00 d0 d7 05 9d 82
dvb0_0: filter mask=ff ff ff ff ff ff
dvb_net_feed_start: set multi_secfilter[0]
dvb0_0: filter mac=01 00 5e 00 00 01
dvb0_0: filter mask=ff ff ff ff ff ff
dvb_net_feed_start: start filtering |
e questo un lspci:
| Code: | root@gentoobox darkssj # lspci
0000:00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different version?) (rev c1)
0000:00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
0000:00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
0000:00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
0000:00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
0000:00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
0000:00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
0000:00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
0000:00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
0000:00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
0000:00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
0000:00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet Controller (rev a1)
0000:00:05.0 Multimedia audio controller: nVidia Corporation nForce MultiMedia audio [Via VT82C686B] (rev a2)
0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97 Audio Controler (MCP) (rev a1)
0000:00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI Bridge (rev a3)
0000:00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2)
0000:00:0c.0 PCI bridge: nVidia Corporation nForce2 PCI Bridge (rev a3)
0000:00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1)
0000:01:09.0 Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card (rev 01)
0000:02:01.0 Ethernet controller: 3Com Corporation 3C920B-EMB Integrated Fast Ethernet Controller [Tornado] (rev 40)
0000:03:00.0 VGA compatible controller: nVidia Corporation NV35 [GeForce FX 5900XT] (rev a1) |
Se avete qualche idea...
_________________
Religions are like fireflies. They require darkness in order to shine.
Arthur Schopenhauer
Last edited by flowolf on Sun Jun 20, 2004 2:55 pm; edited 1 time in total |
|
| Back to top |
|
 |
Sparker
l33t
Joined: 28 Aug 2003
Posts: 992
|
| Posted: Sun Jun 20, 2004 1:06 pm Post subject: |
|
|
Ho lo stesso problema, sempre scheda nForce2 e sempre IRQ 11
Lo faceva anche nel 2.6.6 (e pure 2.6.6-mmX)
Confrontando i dmesg del 2.6.5 e del 2.6.7, nella parte ACPI del 2.6.5 non c'erano tutti quei disabled, anzi, non c'erano proprio |
|
| Back to top |
|
|
Sparker
l33t
Joined: 28 Aug 2003
Posts: 992
|
| Posted: Sun Jun 20, 2004 1:31 pm Post subject: |
|
|
Aggiornamento:
Il problema è il driver USB2.0 che chissà perchè disabilita un IRQ già in uso.
Per il momento ho risolto eliminando il modulo dal kernel.
Il driver USB1.0 invece non dà problemi. |
|
| Back to top |
|
|
flowolf
Tux's lil' helper
Joined: 22 Jun 2003
Posts: 143
|
| Posted: Sun Jun 20, 2004 1:34 pm Post subject: |
|
|
Proverò al più presto, intanto ho già aperto un bug: https://bugs.gentoo.org/show_bug.cgi?id=54514 .
Appena fatta la prova aggiorno il bug...
_________________
Religions are like fireflies. They require darkness in order to shine.
Arthur Schopenhauer |
|
| Back to top |
|
|
Sparker
l33t
Joined: 28 Aug 2003
Posts: 992
|
|
| Back to top |
|
|
flowolf
Tux's lil' helper
Joined: 22 Jun 2003
Posts: 143
|
| Posted: Sun Jun 20, 2004 2:16 pm Post subject: |
|
|
Effettivamente i problemi vengono risolti togliendo il supporto USB 2.0 dal kernel, per quanto riguarda il bug che mi hai segnalato ammetto di non averlo controllato, tuttavia il titolo sembrava ben lontano dal mio problema... 
_________________
Religions are like fireflies. They require darkness in order to shine.
Arthur Schopenhauer |
|
| Back to top |
|
|
motaboy
Developer
Joined: 15 Dec 2003
Posts: 1483
|
| Posted: Sun Jun 20, 2004 6:57 pm Post subject: |
|
|
Posso consigliarvi di cercare se dicono qualcosa sulla mailin del kernel o acpi o usb? oppure riportare il bug li. Magari su usb-devel.
Perchè non credo che un bug solo per la gentoo possa risolvere il problema in tempi brevi... Almeno li possono fornirvi delle patch da provare.
_________________
... |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Forum italiano (Italian)
