Getting cdburner to work with ATAPI in 2.6

Message

mariux2 · Post by **mariux2** » Mon Dec 22, 2003 1:39 pm

Hi, i have been trying to get my cdburner to work with 2.6 kernel but without any luck, i had it working with scsi-emulation in 2.4

My burner is detected properly (i have removed the scsi-append thing from lilo (and rerun it))

Code: Select all

igor cdrdao # cdrecord -scanbus
Cdrecord-Clone 2.01a19 (i686-pc-linux-gnu) Copyright (C) 1995-2003 Jörg Schilling
Using libscg version 'schily-0.7'
scsibus0:
        0,0,0     0) *
        0,1,0     1) 'ATAPI   ' 'CD-RW 52XMax    ' '140D' Removable CD-ROM
        0,2,0     2) *
        0,3,0     3) *
        0,4,0     4) *
        0,5,0     5) *
        0,6,0     6) *
        0,7,0     7) *

Code: Select all

igor cdrdao # cdrecord dev=ATAPI -scanbus
Cdrecord-Clone 2.01a19 (i686-pc-linux-gnu) Copyright (C) 1995-2003 Jörg Schilling
scsidev: 'ATAPI'
devname: 'ATAPI'
scsibus: -2 target: -2 lun: -2
Warning: Using ATA Packet interface.
Warning: The related libscg interface code is in pre alpha.
Warning: There may be fatal problems.
Using libscg version 'schily-0.7'
scsibus0:
        0,0,0     0) *
        0,1,0     1) 'ATAPI   ' 'CD-RW 52XMax    ' '140D' Removable CD-ROM
        0,2,0     2) *
        0,3,0     3) *
        0,4,0     4) *
        0,5,0     5) *
        0,6,0     6) *
        0,7,0     7) *

Code: Select all

igor cdrdao # cdrecord dev=/dev/hdb speed=16 -pad -swab /home/mariux/dilbert.iso 
Cdrecord-Clone 2.01a19 (i686-pc-linux-gnu) Copyright (C) 1995-2003 Jörg Schilling
scsidev: '/dev/hdb'
devname: '/dev/hdb'
scsibus: -2 target: -2 lun: -2
Warning: Open by 'devname' is unintentional and not supported.
Linux sg driver version: 3.5.27
Using libscg version 'schily-0.7'
Device type    : Removable CD-ROM
Version        : 0
Response Format: 1
Vendor_info    : 'ATAPI   '
Identifikation : 'CD-RW 52XMax    '
Revision       : '140D'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO RAW/R96R
cdrecord: Success. test unit ready: scsi sendcmd: no error
CDB:  00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 3A 01 00 00
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x3A Qual 0x01 (medium not present - tray closed) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.000s timeout 40s
cdrecord: No disk / Wrong disk!

Code: Select all

igor cdrdao # cdrecord dev=0,1,0 speed=16 -v /home/mariux/dilbert.iso 
Cdrecord-Clone 2.01a19 (i686-pc-linux-gnu) Copyright (C) 1995-2003 Jörg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,1,0'
scsibus: 0 target: 1 lun: 0
Using libscg version 'schily-0.7'
SCSI buffer size: 32768
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 1
Vendor_info    : 'ATAPI   '
Identifikation : 'CD-RW 52XMax    '
Revision       : '140D'
Device seems to be: Generic mmc CD-RW.
Current: 0x0000
Profile: 0x0008 
Profile: 0x0009 
Profile: 0x000A 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO RAW/R96R
Drive buf size : 1994752 = 1948 KB
FIFO size      : 4194304 = 4096 KB
Track 01: data   527 MB        
Total size:      605 MB (59:58.36) = 269877 sectors
Lout start:      605 MB (60:00/27) = 269877 sectors
cdrecord: Success. test unit ready: scsi sendcmd: no error
CDB:  00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 3A 01 00 00
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x3A Qual 0x01 (medium not present - tray closed) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.000s timeout 40s
cdrecord: No disk / Wrong disk!

Code: Select all

igor cdrdao # cdrecord dev=ATAPI:0,1,0 speed=16 -v /home/mariux/dilbert.iso 
Cdrecord-Clone 2.01a19 (i686-pc-linux-gnu) Copyright (C) 1995-2003 Jörg Schilling
TOC Type: 1 = CD-ROM
scsidev: 'ATAPI:0,1,0'
devname: 'ATAPI'
scsibus: 0 target: 1 lun: 0
Warning: Using ATA Packet interface.
Warning: The related libscg interface code is in pre alpha.
Warning: There may be fatal problems.
Using libscg version 'schily-0.7'
SCSI buffer size: 64512
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 1
Vendor_info    : 'ATAPI   '
Identifikation : 'CD-RW 52XMax    '
Revision       : '140D'
Device seems to be: Generic mmc CD-RW.
Current: 0x0000
Profile: 0x0008 
Profile: 0x0009 
Profile: 0x000A 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO RAW/R96R
Drive buf size : 1994752 = 1948 KB
FIFO size      : 4194304 = 4096 KB
Track 01: data   527 MB        
Total size:      605 MB (59:58.36) = 269877 sectors
Lout start:      605 MB (60:00/27) = 269877 sectors
cdrecord: No disk / Wrong disk!

Code: Select all

igor cdrdao # cdrecord dev=ATAPI:/dev/hdb speed=16 -v /home/mariux/dilbert.iso 
Cdrecord-Clone 2.01a19 (i686-pc-linux-gnu) Copyright (C) 1995-2003 Jörg Schilling
TOC Type: 1 = CD-ROM
scsidev: 'ATAPI:/dev/hdb'
devname: 'ATAPI:/dev/hdb'
scsibus: -2 target: -2 lun: -2
Warning: Using ATA Packet interface.
Warning: The related libscg interface code is in pre alpha.
Warning: There may be fatal problems.
Using libscg version 'schily-0.7'
SCSI buffer size: 64512
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 1
Vendor_info    : 'ATAPI   '
Identifikation : 'CD-RW 52XMax    '
Revision       : '140D'
Device seems to be: Generic mmc CD-RW.
Current: 0x0000
Profile: 0x0008 
Profile: 0x0009 
Profile: 0x000A 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO RAW/R96R
Drive buf size : 1994752 = 1948 KB
FIFO size      : 4194304 = 4096 KB
Track 01: data   527 MB        
Total size:      605 MB (59:58.36) = 269877 sectors
Lout start:      605 MB (60:00/27) = 269877 sectors
cdrecord: No disk / Wrong disk!

I've tried both alpha14 and 20 of cdrtools
And i am running cdrdao 1.1.7-r1
You i DO have a cd in the cdburner:-)
I currently have scsi-emulation compiled into the kernel (i didnt have at first and it made any difference )

I have updated to k3b 0.10.3 but that didnt help either:
Burning iso:

Code: Select all

System
-----------------------
K3b Version: 0.10.3
KDE Version: 3.1.4
QT Version:  3.2.3

cdrecord
-----------------------
scsidev: '/dev/ide/host0/bus0/target1/lun0/cd'
devname: '/dev/ide/host0/bus0/target1/lun0/cd'
scsibus: -2 target: -2 lun: -2
Warning: Open by 'devname' is unintentional and not supported.
Linux sg driver version: 3.5.27
SCSI buffer size: 64512
Cdrecord-Clone 2.01a19 (i686-pc-linux-gnu) Copyright (C) 1995-2003 Jörg Schilling
TOC Type: 1 = CD-ROM
Using libscg version 'schily-0.7'
Driveropts: 'burnfree'
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 1
Vendor_info    : 'ATAPI   '
Identifikation : 'CD-RW 52XMax    '
Revision       : '140D'
Device seems to be: Generic mmc CD-RW.
Current: 0x0000
Profile: 0x0008 
Profile: 0x0009 
Profile: 0x000A 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO RAW/R96R
Drive buf size : 1994752 = 1948 KB
FIFO size      : 4194304 = 4096 KB
/usr/bin/cdrecord: Success. test unit ready: scsi sendcmd: no error
CDB:  00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 3A 01 00 00
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x3A Qual 0x01 (medium not present - tray closed) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.000s timeout 200s
/usr/bin/cdrecord: No disk / Wrong disk!
Track 01: data   527 MB        
Total size:      605 MB (59:58.33) = 269875 sectors
Lout start:      605 MB (60:00/25) = 269875 sectors

cdrecord comand:
-----------------------
/usr/bin/cdrecord -v gracetime=2 dev=/dev/ide/host0/bus0/target1/lun0/cd speed=16 -dao driveropts=burnfree -eject -overburn -data /home/mariux/dilbert.iso

(it asks for an empty cd, i push "Force")

Burning data:

Code: Select all

System
-----------------------
K3b Version: 0.10.3
KDE Version: 3.1.4
QT Version:  3.2.3

cdrecord
-----------------------
Cdrecord-Clone 2.01a19 (i686-pc-linux-gnu) Copyright (C) 1995-2003 Jörg Schilling
TOC Type: 1 = CD-ROM
Using libscg version 'schily-0.7'
Driveropts: 'burnfree'
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 1
Vendor_info    : 'ATAPI   '
Identifikation : 'CD-RW 52XMax    '
Revision       : '140D'
Device seems to be: Generic mmc CD-RW.
Current: 0x0000
Profile: 0x0008 
Profile: 0x0009 
Profile: 0x000A 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO RAW/R96R
Drive buf size : 1994752 = 1948 KB
FIFO size      : 4194304 = 4096 KB
scsidev: '/dev/ide/host0/bus0/target1/lun0/cd'
devname: '/dev/ide/host0/bus0/target1/lun0/cd'
scsibus: -2 target: -2 lun: -2
Warning: Open by 'devname' is unintentional and not supported.
Linux sg driver version: 3.5.27
SCSI buffer size: 64512
/usr/bin/cdrecord: Success. test unit ready: scsi sendcmd: no error
CDB:  00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0A 00 00 00 00 3A 01 00 00
Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x3A Qual 0x01 (medium not present - tray closed) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.000s timeout 200s
/usr/bin/cdrecord: No disk / Wrong disk!
Track 01: data   527 MB        
Total size:      605 MB (59:58.33) = 269875 sectors
Lout start:      605 MB (60:00/25) = 269875 sectors

cdrecord comand:
-----------------------
/usr/bin/cdrecord -v gracetime=2 dev=/dev/ide/host0/bus0/target1/lun0/cd speed=16 -dao driveropts=burnfree -eject -overburn -data -tsize=269875s - 

mkisofs
-----------------------
269875

mkisofs comand:
-----------------------
/usr/bin/mkisofs -gui -graft-points -V K3b data project -volset  -A K3B THE CD KREATOR VERSION 0.10.3 (C) 2003 SEBASTIAN TRUEG AND THE K3B TEAM -P  -p K3b - Version 0.10.3 -sysid LINUX -volset-size 1 -volset-seqno 1 -sort /tmp/kde-mariux/k3b6XfUwa.tmp -r -hide-list /tmp/kde-mariux/k3bqgFoQa.tmp -l -iso-level 2 -path-list /tmp/kde-mariux/k3bsBu6mc.tmp

(it asks for an empty cd, i push "Force")

Do i have to enable anything specific to be able to burn with atapi?

mariux2 · Post by **mariux2** » Mon Dec 22, 2003 1:42 pm

here is my dmesg:

Code: Select all

1, io base 00001840
uhci_hcd 0000:00:14.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
drivers/usb/core/usb.c: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
drivers/usb/core/usb.c: registered new driver usb-storage
USB Mass Storage support registered.
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
drivers/usb/core/usb.c: registered new driver xpad
drivers/usb/input/xpad.c: X-Box pad driver:v0.0.5
mice: PS/2 mouse device common for all mice
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Translated Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
i2c /dev entries driver
vt596 smbus 0000:00:14.4: SMBus base address uninitialized - upgrade BIOS or use force_addr=0xaddr
Advanced Linux Sound Architecture Driver Version 1.0.0rc2.
request_module: failed /sbin/modprobe -- snd-card-0. error = -16
ALSA device list:
  #0: Sound Blaster Live! (rev.7) at 0x1800, irq 10
NET: Registered protocol family 2
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0040d01222a1d171]
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 131072 bind 65536)
ip_conntrack version 2.1 (4096 buckets, 32768 max) - 300 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.  http://snowman.net/projects/ipt_recent/
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
ACPI: (supports S0 S1 S5)
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hdd3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hdd3) for (hdd3)
Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 396k freed
Adding 506512k swap on /dev/hdd2.  Priority:-1 extents:1
nvidia: no version magic, tainting kernel.
nvidia: module license 'NVIDIA' taints kernel.
0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module  1.0-4496  Wed Jul 16 19:03:09 PDT 2003
found reiserfs format "3.6" with standard journal
Reiserfs journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
reiserfs: checking transaction log (hda5) for (hda5)
Using r5 hash to sort names
eth0: link up, 10Mbps, half-duplex, lpa 0x0000
eth1: link up, 10Mbps, half-duplex, lpa 0x0000
eth0: no IPv6 routers present
eth1: no IPv6 routers present
bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size 30119 bytes, found (1280x1024, 30961 bytes, v3).
bootsplash: status on console 0 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size 30119 bytes, found (1280x1024, 30961 bytes, v3).
bootsplash: status on console 1 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size 30119 bytes, found (1280x1024, 30961 bytes, v3).
bootsplash: status on console 2 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size 30119 bytes, found (1280x1024, 30961 bytes, v3).
bootsplash: status on console 3 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size 30119 bytes, found (1280x1024, 30961 bytes, v3).
bootsplash: status on console 4 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size 30119 bytes, found (1280x1024, 30961 bytes, v3).
bootsplash: status on console 5 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size 30119 bytes, found (1280x1024, 30961 bytes, v3).
bootsplash: status on console 6 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size 30119 bytes, found (1280x1024, 30961 bytes, v3).
bootsplash: status on console 7 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size 30119 bytes, found (1280x1024, 30961 bytes, v3).
bootsplash: status on console 8 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size 30119 bytes, found (1280x1024, 30961 bytes, v3).
bootsplash: status on console 9 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size 30119 bytes, found (1280x1024, 30961 bytes, v3).
bootsplash: status on console 10 changed to on
bootsplash 3.1.3-2003/11/14: looking for picture.... silentjpeg size 30119 bytes, found (1280x1024, 30961 bytes, v3).
bootsplash: status on console 11 changed to on
Debug: sleeping function called from invalid context at mm/slab.c:1856
in_atomic():1, irqs_disabled():0
Call Trace:
 [<c011d28c>] __might_sleep+0xac/0xe0
 [<c013f527>] kmem_cache_alloc+0x67/0x70
 [<c014e1e1>] __get_vm_area+0x21/0x100
 [<c014e2f3>] get_vm_area+0x33/0x40
 [<c011a5a2>] __ioremap+0xc2/0x120
 [<c011a629>] ioremap_nocache+0x29/0xb0
 [<e1b90465>] os_map_kernel_space+0x68/0x6c [nvidia]
 [<e1ba2a57>] __nvsym00568+0x1f/0x2c [nvidia]
 [<e1ba4b76>] __nvsym00775+0x6e/0xe0 [nvidia]
 [<e1ba4c06>] __nvsym00781+0x1e/0x190 [nvidia]
 [<e1ba668c>] rm_init_adapter+0xc/0x10 [nvidia]
 [<e1b8cee0>] nv_kern_open+0xf5/0x232 [nvidia]
 [<c015d470>] chrdev_open+0xc0/0x1d0
 [<c01b99ad>] devfs_open+0xed/0x110
 [<c0152fd2>] dentry_open+0x112/0x180
 [<c0152eb6>] filp_open+0x66/0x70
 [<c01532c5>] sys_open+0x55/0x90
 [<c010b4cb>] syscall_call+0x7/0xb

Debug: sleeping function called from invalid context at mm/slab.c:1856
in_atomic():1, irqs_disabled():0
Call Trace:
 [<c011d28c>] __might_sleep+0xac/0xe0
 [<c013f527>] kmem_cache_alloc+0x67/0x70
 [<c014e1e1>] __get_vm_area+0x21/0x100
 [<c014e2f3>] get_vm_area+0x33/0x40
 [<c011a5a2>] __ioremap+0xc2/0x120
 [<c011a629>] ioremap_nocache+0x29/0xb0
 [<e1b90465>] os_map_kernel_space+0x68/0x6c [nvidia]
 [<e1ba2a57>] __nvsym00568+0x1f/0x2c [nvidia]
 [<e1ba4b76>] __nvsym00775+0x6e/0xe0 [nvidia]
 [<e1ba4c06>] __nvsym00781+0x1e/0x190 [nvidia]
 [<e1ba668c>] rm_init_adapter+0xc/0x10 [nvidia]
 [<e1b8cee0>] nv_kern_open+0xf5/0x232 [nvidia]
 [<c015d470>] chrdev_open+0xc0/0x1d0
 [<c01b99ad>] devfs_open+0xed/0x110
 [<c0152fd2>] dentry_open+0x112/0x180
 [<c0152eb6>] filp_open+0x66/0x70
 [<c01532c5>] sys_open+0x55/0x90
 [<c010b4cb>] syscall_call+0x7/0xb

Debug: sleeping function called from invalid context at mm/slab.c:1856
in_atomic():1, irqs_disabled():0
Call Trace:
 [<c011d28c>] __might_sleep+0xac/0xe0
 [<e1ba2928>] __nvsym00323+0x10/0x14 [nvidia]
 [<c013f5b9>] __kmalloc+0x89/0x90
 [<e1b8fbee>] os_alloc_mem+0x5c/0x87 [nvidia]
 [<e1ba2b74>] __nvsym00083+0x10/0x24 [nvidia]
 [<e1c4b34f>] __nvsym03944+0x1af/0x2c0 [nvidia]
 [<e1cb2bbd>] __nvsym00780+0x11d/0x224 [nvidia]
 [<e1ba47bc>] __nvsym00773+0x1c/0x5c [nvidia]
 [<e1ba4d03>] __nvsym00781+0x11b/0x190 [nvidia]
 [<e1ba668c>] rm_init_adapter+0xc/0x10 [nvidia]
 [<e1b8cee0>] nv_kern_open+0xf5/0x232 [nvidia]
 [<c015d470>] chrdev_open+0xc0/0x1d0
 [<c01b99ad>] devfs_open+0xed/0x110
 [<c0152fd2>] dentry_open+0x112/0x180
 [<c0152eb6>] filp_open+0x66/0x70
 [<c01532c5>] sys_open+0x55/0x90
 [<c010b4cb>] syscall_call+0x7/0xb

agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode

infirit · Post by **infirit** » Mon Dec 22, 2003 4:53 pm

It has been sugested on the web to upgrade the firmware and/or change a non branded cdrw to a branded one. It working fine for me with 2.6 final and Cdrecord-Clone 2.01a19

mariux2 · Post by **mariux2** » Mon Dec 22, 2003 6:22 pm

Seems i posted it in the wrong part of the forum, oh well...

sj7trunks · Post by **sj7trunks** » Mon Dec 22, 2003 6:54 pm

Try using --device=0,1,0
that works just fine for me in my 2.6 kernel

mariux2 · Post by **mariux2** » Mon Dec 22, 2003 7:07 pm

no that didnt change anything, specially since --device isnt a legal switch in cdrecord, so i changed it to --dev and that is the same as i had further up in this thread...

mariux2 · Post by **mariux2** » Tue Dec 23, 2003 10:01 pm

Turns out the cdburner doesnt work as a reader either

Code: Select all

igor mnt # mount /dev/cdrom /mnt/cdrom/
mount: block device /dev/cdrom is write-protected, mounting read-only
mount: No medium found

Same error, "no cd in inserted" BUT IT IS!

mariux2 · Post by **mariux2** » Wed Dec 24, 2003 1:54 pm

Same problem with 2.6.0-mm1

mariux2 · Post by **mariux2** » Wed Dec 24, 2003 11:04 pm

The problem was not there in 2.6.0-test9........

hielvc · Post by **hielvc** » Thu Dec 25, 2003 2:22 am

When I looked at my dmesg it said ide-scsi was depreciated and to use in lilo or grub hdc=ide-cd. To mount use /dev/hdc. Now it mounts and cdrecord dev=ATAPi:1,1,1 is recognized.
Output of dmesg:

Code: Select all

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Dec 23 19:08:48 tester kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Dec 23 19:08:48 tester kernel: VP_IDE: IDE controller at PCI slot 0000:00:11.1
Dec 23 19:08:48 tester kernel: VP_IDE: chipset revision 6
Dec 23 19:08:48 tester kernel: VP_IDE: not 100%% native mode: will probe irqs later
Dec 23 19:08:48 tester kernel: VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
Dec 23 19:08:48 tester kernel:     ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:DMA, hdb:pio
Dec 23 19:08:48 tester kernel:     ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:DMA, hdd:pio
Dec 23 19:08:48 tester kernel: hda: HDS722580VLAT20, ATA DISK drive
Dec 23 19:08:48 tester kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Dec 23 19:08:48 tester kernel: hdc: OPTORITE CD-RW CW4002, ATAPI CD/DVD-ROM drive
Dec 23 19:08:48 tester kernel: ide1 at 0x170-0x177,0x376 on irq 15
Dec 23 19:08:48 tester kernel: hda: max request size: 1024KiB
Dec 23 19:08:48 tester kernel: hda: 160836480 sectors (82348 MB) w/1794KiB Cache, CHS=16383/255/63, UDMA(100)
Dec 23 19:08:48 tester kernel:  /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 >
Dec 23 19:08:48 tester kernel: ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as device
Dec 23 19:08:48 tester kernel: scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Dec 23 19:08:48 tester kernel:   Vendor: OPTORITE  Model: CD-RW CW4002      Rev: 100E
Dec 23 19:08:48 tester kernel:   Type:   CD-ROM                             ANSI SCSI revision: 02
Dec 23 19:08:48 tester kernel: sr0: scsi3-mmc drive: 4x/40x writer cd/rw xa/form2 cdda tray
Dec 23 19:08:48 tester kernel: Uniform CD-ROM driver Revision: 3.12
Dec 23 19:08:48 tester kernel: Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 5

hielvc

mariux2 · Post by **mariux2** » Thu Dec 25, 2003 5:00 pm

Tried passing ide-cd as an argument in lilo, didnt help!

mariux2 · Post by **mariux2** » Thu Dec 25, 2003 5:02 pm

Looking in dmesg now i see:
during boot:

Code: Select all

 /dev/ide/host0/bus1/target1/lun0: p1 p2 p3
cdrom: : unknown mrw mode page
hdb: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
end_request: I/O error, dev hdb, sector 0

later, probably when trying to mount the cd:

Code: Select all

end_request: I/O error, dev hdb, sector 0
cdrom: open failed.
end_request: I/O error, dev hdb, sector 0
cdrom: open failed.

hielvc · Post by **hielvc** » Sat Dec 27, 2003 12:12 am

That error in your dmesg

Code: /dev/ide/host0/bus1/target1/lun0: p1 p2 p3
cdrom: : unknown mrw mode page
hdb: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
end_request: I/O error, dev hdb, sector 0

doesnt look good. My dmesg the right one this time

Code: Select all

hdc: OPTORITE CD-RW CW4002, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 160836480 sectors (82348 MB) w/1794KiB Cache, CHS=16383/255/63, UDMA(100)
 /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 >
hdc: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12

shows no errors. YOurs is acting like a hard drive. You have a flaky burner.

hielvc

CrimsonScythe · Post by **CrimsonScythe** » Sat Dec 27, 2003 1:08 pm

I think this is a kernel-issue. I had ATAPI burning working just fine under 2.6.0-test11, but it broke when I installed 2.6.0-mm1. Now I have the same error mesages as you in dmesg:

Code: Select all

cdrom: : unknown mrw mode page
hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
end_request: I/O error, dev hdb, sector 0

Lets hope this will get fixed soon.

hielvc · Post by **hielvc** » Mon Dec 29, 2003 3:53 pm

This just a thought but do you have UDF,packet writing, enabled ? Thats File systems>> CD-ROM/DVD Filesystems >> UDF file system support, if so try without it.

hielvc

mariux2 · Post by **mariux2** » Mon Dec 29, 2003 4:22 pm

CrimsonScythe wrote:I think this is a kernel-issue. I had ATAPI burning working just fine under 2.6.0-test11, but it broke when I installed 2.6.0-mm1. Now I have the same error mesages as you in dmesg:
Code: Select all
cdrom: : unknown mrw mode page
hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
end_request: I/O error, dev hdb, sector 0
Lets hope this will get fixed soon.

SAME FOR ME!
It worked great in test9, but is now broken....

I`ll try to recompile it without UDP tomorrow....

tgnb · Post by **tgnb** » Tue Dec 30, 2003 2:56 am

Same problem vanilla 2.6.0 .. disabling UDF filesuystem support didn't help me.

mariux2 · Post by **mariux2** » Tue Dec 30, 2003 11:56 am

tgnb wrote:Same problem vanilla 2.6.0 .. disabling UDF filesuystem support didn't help me.

I heard it was a known problem....

mariux2 · Post by **mariux2** » Wed Dec 31, 2003 1:39 am

Its not fixed in 2.6.0-mm2 either

camresu · Post by **camresu** » Wed Dec 31, 2003 6:19 pm

mariux2 wrote:
CrimsonScythe wrote:I think this is a kernel-issue. I had ATAPI burning working just fine under 2.6.0-test11, but it broke when I installed 2.6.0-mm1. Now I have the same error mesages as you in dmesg:
Code: Select all
cdrom: : unknown mrw mode page
hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
end_request: I/O error, dev hdb, sector 0
Lets hope this will get fixed soon.
SAME FOR ME!

Same for me what gives with end_request: I/O error, ???
using gentoo-dev-sources-2.6.0

HeadHolio · Post by **HeadHolio** » Thu Jan 01, 2004 8:54 pm

I am experiencing this problem with mm-sources 2.6.0 and ATAPI burning on one system with a Mitsumi cd Burner, but I am NOT experiencing this problem on a cloned system (same kernel) with a LiteOn burner. I want to try just swaping burners and seeing how that works. I'll let everyone know what I find....gonna be a couple days until I can try it

Just so you know, both burners work fine with SCSI emulation and an older kernel. But who wants to use that?????

ozukir@ · Post by **ozukir@** » Thu Jan 01, 2004 11:57 pm

D@mmit!

Code: Select all

hdc: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
end_request: I/O error, dev hdc, sector 0
cdrom: : unknown mrw mode page
hdd: ATAPI DVD-ROM drive, 512kB Cache, UDMA(33)
end_request: I/O error, dev hdd, sector 0

But I can mount and read disks fine (with occassional hiccup in the logs).

HeadHolio · Post by **HeadHolio** » Fri Jan 02, 2004 1:10 am

I can also mount and read disks fine.

ozukir@ · Post by **ozukir@** » Fri Jan 02, 2004 9:02 am

So far I can report success with gentoo-dev-sources-2.6.0-r1. Relevant dmesg output:

Code: Select all

hdc: HL-DT-ST CD-RW GCE-8240B, ATAPI CD/DVD-ROM drive
hdc: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache, DMA

Code: Select all

 > cdrecord dev=ATAPI -scanbus
Cdrecord 2.01a14 (i686-pc-linux-gnu) Copyright (C) 1995-2003 J�rg Schilling
scsidev: 'ATAPI'
devname: 'ATAPI'
scsibus: -2 target: -2 lun: -2
Warning: Using ATA Packet interface.
Warning: The related libscg interface code is in pre alpha.
Warning: There may be fatal problems.
Using libscg version 'schily-0.7'
scsibus0:
    0,0,0     0) 'HL-DT-ST' 'CD-RW GCE-8240B ' '1.07' Removable CD-ROM
cdrecord: Warning: controller returns wrong size for CD capabilities page.
    0,1,0     1) 'Compaq  ' 'DVD-ROM DVD-113R' '1.10' Removable CD-ROM
<snip>

Doing the deed:

Code: Select all

 > cdrecord dev=ATAPI:0,0,0 driveropts=burnfree -dao cuefile=videocd.cue

is successful.

I simply emerged the masked gentoo-dev-sources, ran make oldconfig on my config from mm2, and removed all scsi options (except for CONFIG_SCSI=m which cannot be removed). I don't know how the patchsets differ, but it works for me.

georgie · Post by **georgie** » Fri Jan 02, 2004 9:12 am

Dunno if this uses ATAPI or not, but after moving to kernel 2.6, I had to start passing the dev=/dev/hdd* switch to cdrecord in order to get it to work.,

hth

george

*hdd being where my cd-burner is, obviously

Getting cdburner to work with ATAPI in 2.6

Getting cdburner to work with ATAPI in 2.6

Fix

Same for me

2.6.0-mm2

Yeah me too

I used dev=/dev/hd*