Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
wlan0: link is not ready
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Networking & Security
View previous topic :: View next topic  
Author Message
Sigma Kappa
n00b
n00b


Joined: 04 Mar 2012
Posts: 45

PostPosted: Thu Sep 12, 2013 12:20 pm    Post subject: wlan0: link is not ready Reply with quote

Hi,

the problem I encountered is "link is not ready". The appropriate "dmesg" and "rc.log" are listed below --- that's as far as I could get..
By passing the appropriate parameter to kernel I made sure network interfaces are not renamed.

My /etc/conf.d/net:

Code:
# This blank configuration will automatically use DHCP for any net.*
# scripts in /etc/init.d.  To create a more complete configuration,
# please review /usr/share/doc/openrc*/net.example* and save your configuration
# in /etc/conf.d/net (this file :]!).
modules="wpa_supplicant"
wpa_supplicant_wlan0="-iwlan0 -Dwext -c/etc/wpa_supplicant/wpa_supplicant.conf -d"
wpa_supplicant_wlan1="-iwlan1 -Dwext -c/etc/wpa_supplicant/wpa_supplicant.conf -d"
config_wlan0="dhcp"
config_wlan1="dhcp"



My wpa_supplicant.conf:

Code:

# wpa_supplicant -iwlan0 -c/etc/wpa_supplicant/wpa_supplicant.conf -d
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=wheel

update_config=1

# ap_scan=1

network={
   ssid="mySSID"
   psk="myPassphrase"
   priority=5
}


Code:

rc shutdown logging started at Thu Sep 12 21:58:32 2013

 * Caching service dependencies ...
 [ ok ]
 * Stopping local
 [ ok ]
 * Stopping gdm ...
 [ ok ]
 * Saving random seed ...
 [ ok ]
 * Deactivating additional swap space ...
 [ ok ]
 * Stopping syslog-ng ...
 [ ok ]
 * Bringing down interface wlan0
 *   Removing addresses
 *     Stopping wpa_cli on wlan0 ...
 [ ok ]
 *     Stopping wpa_supplicant on wlan0 ...
 [ ok ]
 * Bringing down interface lo
 *   Removing addresses
 *     ::1
 * Stopping D-BUS system messagebus ...
 [ ok ]
 * Unmounting loop devices
 * Unmounting filesystems
 *   Unmounting /boot ...
 [ ok ]
 * Deactivating swap devices ...
 [ ok ]
 * Stopping udev ...
 [ ok ]
 * Setting hardware clock using the system clock [UTC] ...
 [ ok ]

rc shutdown logging stopped at Thu Sep 12 21:58:34 2013


rc shutdown logging started at Thu Sep 12 21:58:32 2013

 * Caching service dependencies ...
 [ ok ]
 * Stopping local
 [ ok ]
 * Stopping gdm ...
 [ ok ]
 * Saving random seed ...
 [ ok ]
 * Deactivating additional swap space ...
 [ ok ]
 * Stopping syslog-ng ...
 [ ok ]
 * Bringing down interface wlan0
 *   Removing addresses
 *     Stopping wpa_cli on wlan0 ...
 [ ok ]
 *     Stopping wpa_supplicant on wlan0 ...
 [ ok ]
 * Bringing down interface lo
 *   Removing addresses
 *     ::1
 * Stopping D-BUS system messagebus ...
 [ ok ]
 * Unmounting loop devices
 * Unmounting filesystems
 *   Unmounting /boot ...
 [ ok ]
 * Deactivating swap devices ...
 [ ok ]
 * Stopping udev ...
 [ ok ]
 * Setting hardware clock using the system clock [UTC] ...
 [ ok ]

rc shutdown logging stopped at Thu Sep 12 21:58:34 2013


rc boot logging started at Thu Sep 12 21:59:03 2013

 * Setting system clock using the hardware clock [UTC] ...
 [ ok ]
 * Autoloaded 0 module(s)
 * Checking local filesystems  ...
/dev/sda7: clean, 397897/3670016 files, 1864997/14653696 blocks
/dev/sda5: clean, 35/25688 files, 24124/102400 blocks
 [ ok ]
 * Remounting root filesystem read/write ...
 [ ok ]
 * Remounting filesystems ...
 [ ok ]
 * Updating /etc/mtab ...
 [ ok ]
 * Activating swap devices ...
 [ ok ]
 * Mounting local filesystems ...
 [ ok ]
 * Configuring kernel parameters ...
 [ ok ]
 * Creating user login records ...
 [ ok ]
 * Cleaning /var/run ...
 [ ok ]
 * Wiping /tmp directory ...
 [ ok ]
 * Setting hostname to hp05_202 ...
 [ ok ]
 * Setting terminal encoding [UTF-8] ...
 [ ok ]
 * Setting keyboard mode [UTF-8] ...
 [ ok ]
 * Loading key mappings [us] ...
 [ ok ]
 * Bringing up interface lo
 *   127.0.0.1/8 ...
 [ ok ]
 *   Adding routes
 *     127.0.0.0/8 via 127.0.0.1 ...
 [ ok ]
 * Mounting misc binary format filesystem ...
 [ ok ]
 * Loading custom binary format handlers ...
 [ ok ]
 * Activating additional swap space ...
 [ ok ]
 * setting up tmpfiles.d entries ...
 [ ok ]
 * Initializing random number generator ...
 [ ok ]

rc boot logging stopped at Thu Sep 12 21:59:05 2013


rc default logging started at Thu Sep 12 21:59:05 2013

 * Starting D-BUS system messagebus ...
 [ ok ]
 * Bringing up interface wlan0
 *   Starting wpa_supplicant on wlan0 ...
Initializing interface 'wlan0' conf '/etc/wpa_supplicant/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant/wpa_supplicant.conf' -> '/etc/wpa_supplicant/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group='wheel'
update_config=1
Priority group 5
   id=0 ssid='SSID'
WEXT: cfg80211-based driver detected
ioctl[SIOCSIWMODE]: Operation not supported
Could not configure driver to use managed mode
ioctl[SIOCGIWRANGE]: Operation not supported
ioctl[SIOCGIWMODE]: Operation not supported
ioctl[SIOCSIWAP]: Operation not supported
WEXT: Failed to clear to disconnect
netlink: Operstate: linkmode=1, operstate=5
Own MAC address: d0:df:9a:0f:e1:66
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: Operation not supported
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
ioctl[SIOCSIWENCODE]: Operation not supported
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: Operation not supported
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
ioctl[SIOCSIWENCODE]: Operation not supported
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: Operation not supported
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
ioctl[SIOCSIWENCODE]: Operation not supported
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: Operation not supported
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
ioctl[SIOCSIWENCODE]: Operation not supported
wpa_driver_wext_set_countermeasures
RSN: flushing PMKID list in the driver
Setting scan request: 0 sec 100000 usec
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: Supplicant port status: Unauthorized
EAPOL: Supplicant port status: Unauthorized
ctrl_interface_group=10 (from group name 'wheel')
Added interface wlan0
Daemonize..
 [ ok ]
 *   Starting wpa_cli on wlan0 ...
 [ ok ]
 *   Backgrounding ... ...
 * WARNING: net.wlan0 has started, but is inactive
 * WARNING: netmount is scheduled to start when net.wlan0 has started
 * Checking your configfile (/etc/syslog-ng/syslog-ng.conf) ...
 [ ok ]
 * Starting syslog-ng ...
 [ ok ]
 * Setting up gdm ...
 [ ok ]
 * Starting local
 [ ok ]

rc default logging stopped at Thu Sep 12 21:59:08 2013

[    7.522491] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[/code]
Back to top
View user's profile Send private message
quilosaq
l33t
l33t


Joined: 22 Dec 2009
Posts: 826

PostPosted: Thu Sep 12, 2013 6:29 pm    Post subject: Reply with quote

What's the output of
Code:
dmesg | grep firmware
?
Back to top
View user's profile Send private message
Sigma Kappa
n00b
n00b


Joined: 04 Mar 2012
Posts: 45

PostPosted: Fri Sep 13, 2013 9:12 am    Post subject: Reply with quote

Code:
dmesg | grep firmware
yields these two lines:

Code:

ieee80211 phy0: rt2x00lib_request_firmware: Info -- Loading firmware file 'rt2860.bin'
ieee80211 phy0: rt2x00lib_request_firmware: Firmware detected - version: 0.34
Back to top
View user's profile Send private message
quilosaq
l33t
l33t


Joined: 22 Dec 2009
Posts: 826

PostPosted: Fri Sep 13, 2013 4:33 pm    Post subject: Reply with quote

Step to step. ¿
Code:
ifconfig -a
?
Back to top
View user's profile Send private message
Sigma Kappa
n00b
n00b


Joined: 04 Mar 2012
Posts: 45

PostPosted: Tue Sep 17, 2013 7:14 am    Post subject: Reply with quote

Code:
eth0: flags=4098<BROADCAST,MULTICAST>  mtu 1500
        ether 2c:41:38:9d:85:d7  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 20  memory 0xfe500000-fe520000 

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 0  (Local Loopback)
        RX packets 28  bytes 1904 (1.8 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 28  bytes 1904 (1.8 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

tunl0: flags=128<NOARP>  mtu 0
        tunnel   txqueuelen 0  (IPIP Tunnel)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether d0:df:9a:0f:e1:66  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
Back to top
View user's profile Send private message
Sigma Kappa
n00b
n00b


Joined: 04 Mar 2012
Posts: 45

PostPosted: Tue Sep 17, 2013 7:31 am    Post subject: Reply with quote

OK, now I\m writing from my Gentoo box! :)
I compiled rt2800pci as a module, without any change to the above wpa_supplicant.conf and /et/conf.d/net.

Thank you all.
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Networking & Security All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum