Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
No Sound over HDMI problems (mostly solved )
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Multimedia
View previous topic :: View next topic  
Author Message
gentoo2013
n00b
n00b


Joined: 20 Feb 2013
Posts: 58
Location: United Kigdom

PostPosted: Fri Apr 26, 2013 11:31 am    Post subject: No Sound over HDMI problems (mostly solved ) Reply with quote

Hi i have gentoo installed and xmbc
I can not get sound working through HDMI. on my tv
Im trying lots of diffrent ways and just cant figure it out.
I have alsa and pulsaudio installed


I have also been following this documentation
http://forums.fedoraforum.org/showthread.php?t=256851
http://www.linuxquestions.org/questions/linux-hardware-18/no-audio-with-nvidia-gts-450-a-852626/#post4209297

Here are someoutpts which may help someone help me figure out whats going on.

Code:
localhost ~ # aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: SB [HDA ATI SB], device 0: VT1708S Analog [VT1708S Analog]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: SB [HDA ATI SB], device 2: VT1708S HP [VT1708S HP]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 1: NVidia [HDA NVidia], device 7: HDMI 1 [HDMI 1]
  Subdevices: 1/1


Code:
localhost ~ # aplay -L
null
    Discard all samples (playback) or generate zero samples (capture)
pulse
    PulseAudio Sound Server
default:CARD=SB
    HDA ATI SB, VT1708S Analog
    Default Audio Device
sysdefault:CARD=SB
    HDA ATI SB, VT1708S Analog
    Default Audio Device
front:CARD=SB,DEV=0
    HDA ATI SB, VT1708S Analog
    Front speakers
surround40:CARD=SB,DEV=0
    HDA ATI SB, VT1708S Analog
    4.0 Surround output to Front and Rear speakers
surround41:CARD=SB,DEV=0
    HDA ATI SB, VT1708S Analog
    4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=SB,DEV=0
    HDA ATI SB, VT1708S Analog
    5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=SB,DEV=0
    HDA ATI SB, VT1708S Analog
    5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=SB,DEV=0
    HDA ATI SB, VT1708S Analog
    7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
hdmi:CARD=NVidia,DEV=0
    HDA NVidia, HDMI 0
    HDMI Audio Output
hdmi:CARD=NVidia,DEV=1
    HDA NVidia, HDMI 1
    HDMI Audio Output


Code:

ocalhost ~ # cat /etc/portage/make.conf
# These settings were set by the catalyst build script that automatically
# built this stage.
# Please consult /usr/share/portage/config/make.conf.example for a more
# detailed example.
CFLAGS="-O2 -march=athlon64 -mtune=generic -pipe"
CXXFLAGS="${CFLAGS}"
# WARNING: Changing your CHOST is not something that should be done lightly.
# Please consult http://www.gentoo.org/doc/en/change-chost.xml before changing.
CHOST="x86_64-pc-linux-gnu"
# These are the USE flags that were used in addition to what is provided by the
# profile used for building.
USE="pulseaudio X g3dvl nvidia xvmc dbus gif opengl jpeg png sqlite apng fuse gudev python policykit mmx sse sse2 alsa cdr dvd gnome -kde consolekit gtk gdu hwdb"
INPUT_DEVICES="evdev keyboard mouse"
VIDEO_CARDS="nvidia"


Code:
localhost ~ # cat /etc/pulse/default.pa
#!/usr/bin/pulseaudio -nF
#
# This file is part of PulseAudio.
#
# PulseAudio is free software; you can redistribute it and/or modify it
# under the terms of the GNU Lesser General Public License as published by
# the Free Software Foundation; either version 2 of the License, or
# (at your option) any later version.
#
# PulseAudio is distributed in the hope that it will be useful, but
# WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
# General Public License for more details.
#
# You should have received a copy of the GNU Lesser General Public License
# along with PulseAudio; if not, write to the Free Software Foundation,
# Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.

# This startup script is used only if PulseAudio is started per-user
# (i.e. not in system mode)

.nofail

### Load something into the sample cache
#load-sample-lazy x11-bell /usr/share/sounds/gtk-events/activate.wav
#load-sample-lazy pulse-hotplug /usr/share/sounds/startup3.wav
#load-sample-lazy pulse-coldplug /usr/share/sounds/startup3.wav
#load-sample-lazy pulse-access /usr/share/sounds/generic.wav

.fail

### Automatically restore the volume of streams and devices
load-module module-device-restore
load-module module-stream-restore
load-module module-card-restore

### Automatically augment property information from .desktop files
### stored in /usr/share/application
load-module module-augment-properties

### Load audio drivers statically
### (it's probably better to not load these drivers manually, but instead
### use module-udev-detect -- see below -- for doing this automatically)
load-module module-alsa-sink device=plughw:1,7
#load-module module-alsa-source device=hw:1,0
#load-module module-null-sink
#load-module module-pipe-sink

### Automatically load driver modules depending on the hardware available
.ifexists module-udev-detect.so
load-module module-udev-detect
.else
### Use the static hardware detection module (for systems that lack udev/hal support)
load-module module-detect
.endif

### Automatically connect sink and source if JACK server is present
.ifexists module-jackdbus-detect.so
.nofail
load-module module-jackdbus-detect
.fail
.endif


### Load several protocols
.ifexists module-esound-protocol-unix.so
load-module module-esound-protocol-unix
.endif
load-module module-native-protocol-unix

### Network access (may be configured with paprefs, so leave this commented
### here if you plan to use paprefs)
#load-module module-esound-protocol-tcp
#load-module module-native-protocol-tcp

### Load the RTP receiver module (also configured via paprefs, see above)
#load-module module-rtp-recv

### Load the RTP sender module (also configured via paprefs, see above)
#load-module module-null-sink sink_name=rtp format=s16be channels=2 rate=44100 sink_properties="device.description='RTP Multicast Sink'"
#load-module module-rtp-send source=rtp.monitor

### Load additional modules from GConf settings. This can be configured with the paprefs tool.
### Please keep in mind that the modules configured by paprefs might conflict with manually
### loaded modules.
.ifexists module-gconf.so
.nofail
load-module module-gconf
.fail
.endif

### Automatically restore the default sink/source when changed by the user
### during runtime
### NOTE: This should be loaded as early as possible so that subsequent modules
### that look up the default sink/source get the right value
load-module module-default-device-restore

### Automatically move streams to the default sink if the sink they are
### connected to dies, similar for sources
load-module module-rescue-streams

### Make sure we always have a sink around, even if it is a null sink.
load-module module-always-sink

### Honour intended role device property
load-module module-intended-roles

### Automatically suspend sinks/sources that become idle for too long
load-module module-suspend-on-idle

### If autoexit on idle is enabled we want to make sure we only quit
### when no local session needs us anymore.
.ifexists module-console-kit.so
load-module module-console-kit
.endif
.ifexists module-systemd-login.so
load-module module-systemd-login
.endif

### Enable positioned event sounds
load-module module-position-event-sounds

### Cork music/video streams when a phone stream is active
load-module module-role-cork

### Modules to allow autoloading of filters (such as echo cancellation)
### on demand. module-filter-heuristics tries to determine what filters
### make sense, and module-filter-apply does the heavy-lifting of
### loading modules and rerouting streams.
load-module module-filter-heuristics
load-module module-filter-apply

### Load DBus protocol
.ifexists module-dbus-protocol.so
load-module module-dbus-protocol
.endif

# X11 modules should not be started from default.pa so that one daemon
# can be shared by multiple sessions.

### Load X11 bell module
#load-module module-x11-bell sample=bell-windowing-system

### Register ourselves in the X11 session manager
#load-module module-x11-xsmp

### Publish connection data in the X11 root window
#.ifexists module-x11-publish.so
#.nofail
#load-module module-x11-publish
#.fail
#.endif

load-module module-switch-on-port-available

### Make some devices default
#set-default-sink output
#set-default-source input


Code:
lspci
01:00.1 Audio device: NVIDIA Corporation GF119 HDMI Audio Controller (rev a1)


I have been messing arounf in the pulseaudio config and now im just getting really confused.
If anyone has any clues please help

thanks [/code]











After playing with configs for hours nothing worked.
I emerged gnome-media went into the sound application in in prefrences on the desktop.
Disabled the internal card and choose one of the 4 hdmi options and it worked.
For some reason inside XBMC the sound output is analog and not HDMI but there is only a HDMI cabled plugged in but its working so I am happy

thanks
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Multimedia All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum