Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
konfigurieren des rtl8367rb sitches (ralink SoC board)
View unanswered posts
View posts from last 24 hours
View posts from last 7 days

 
Reply to topic    Gentoo Forums Forum Index Deutsches Forum (German)
View previous topic :: View next topic  
Author Message
snikkers
n00b
n00b


Joined: 25 Jan 2012
Posts: 15

PostPosted: Sun Jan 20, 2013 10:37 pm    Post subject: konfigurieren des rtl8367rb sitches (ralink SoC board) Reply with quote

hi leute,

habe auf unserem board (rt3662f cpu, mips32el) gentoo gebaut und hänge nun beim netzwerk fest. der lan switch (rtl8367rb) treiber konnte mit einem openwrt system bereits erfolgreich getestet werden.

die konfiguration dazu:
Code:

root@OpenWrt:/# cat /etc/config/network

config interface 'loopback'
        option ifname 'lo'
        option proto 'static'
        option ipaddr '127.0.0.1'
        option netmask '255.0.0.0'

config interface 'lan'
        option ifname 'eth0.1'
        option type 'bridge'
        option proto 'static'
        option ipaddr '192.168.1.1'
        option netmask '255.255.255.0'
root@OpenWrt:/#


die interfaces:
Code:

root@OpenWrt:/# ifconfig
br-lan    Link encap:Ethernet  HWaddr 00:11:22:33:44:55 
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:39 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:5576 (5.4 KiB)  TX bytes:182 (182.0 B)

eth0      Link encap:Ethernet  HWaddr 00:11:22:33:44:55 
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:364 errors:0 dropped:0 overruns:0 frame:0
          TX packets:340 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:363648 (355.1 KiB)  TX bytes:63799 (62.3 KiB)
          Interrupt:5

eth0.1    Link encap:Ethernet  HWaddr 00:11:22:33:44:55 
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:39 errors:0 dropped:0 overruns:0 frame:0
          TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:5576 (5.4 KiB)  TX bytes:458 (458.0 B)

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:378 errors:0 dropped:0 overruns:0 frame:0
          TX packets:378 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:25352 (24.7 KiB)  TX bytes:25352 (24.7 KiB)


kram aus /proc/net/vlan/*
Code:
root@OpenWrt:/# cat /proc/net/vlan/config
VLAN Dev name    | VLAN ID
Name-Type: VLAN_NAME_TYPE_RAW_PLUS_VID_NO_PAD
eth0.1         | 1  | eth0
root@OpenWrt:/# cat /proc/net/vlan/eth0.1
eth0.1  VID: 1   REORDER_HDR: 1  dev->priv_flags: 4001
         total frames received           13
          total bytes received         1676
      Broadcast/Multicast Rcvd            0

      total frames transmitted            5
       total bytes transmitted          274
Device: eth0
INGRESS priority mappings: 0:0  1:0  2:0  3:0  4:0  5:0  6:0 7:0
 EGRESS priority mappings:
root@OpenWrt:/#


kram aus /sys/devices/platform/*
Code:

root@OpenWrt:/# ls /sys/devices/platform/*
/sys/devices/platform/uevent

/sys/devices/platform/alarmtimer:
driver     modalias   subsystem  uevent

/sys/devices/platform/physmap-flash.0:
modalias   subsystem  uevent

/sys/devices/platform/ramips-wdt:
driver     modalias   subsystem  uevent

/sys/devices/platform/ramips_eth.0:
driver          ramips_mdio:05  ramips_mdio:0d  ramips_mdio:15  ramips_mdio:1d
mdio_bus        ramips_mdio:06  ramips_mdio:0e  ramips_mdio:16  ramips_mdio:1e
modalias        ramips_mdio:07  ramips_mdio:0f  ramips_mdio:17  ramips_mdio:1f
ramips_mdio:00  ramips_mdio:08  ramips_mdio:10  ramips_mdio:18  subsystem
ramips_mdio:01  ramips_mdio:09  ramips_mdio:11  ramips_mdio:19  uevent
ramips_mdio:02  ramips_mdio:0a  ramips_mdio:12  ramips_mdio:1a
ramips_mdio:03  ramips_mdio:0b  ramips_mdio:13  ramips_mdio:1b
ramips_mdio:04  ramips_mdio:0c  ramips_mdio:14  ramips_mdio:1c

/sys/devices/platform/regulatory.0:
modalias   subsystem  uevent

/sys/devices/platform/rt3883-ehci:
companion            pools                uframe_periodic_max
driver               subsystem            usb1
modalias             uevent

/sys/devices/platform/rt3883-ohci:
driver     modalias   pools      subsystem  uevent     usb2

/sys/devices/platform/rtl8367b:
driver       modalias     rtl8367b:01  rtl8367b:03  subsystem
mdio_bus     rtl8367b:00  rtl8367b:02  rtl8367b:04  uevent

/sys/devices/platform/serial8250:
driver     modalias   subsystem  tty        uevent


das ist die minimale konfiguration, mit der ich eine andere kiste anpingen kann.

jetzt muss ich dieses setup auf einem gentoo-system durchführen. wo soll ich anfangen und wie gehe ich am besten vor? das thema netzwerke ist leider nicht so meins. ;)
Back to top
View user's profile Send private message
bell
Guru
Guru


Joined: 27 Nov 2007
Posts: 430

PostPosted: Mon Jan 21, 2013 8:41 am    Post subject: Reply with quote

In der /usr/share/doc/openrc-0.11.8/net.example.bz2 gibt es einige Beispiele zum Thema VLAN. Konfiguriert wird in der /etc/conf.d/net.
Back to top
View user's profile Send private message
snikkers
n00b
n00b


Joined: 25 Jan 2012
Posts: 15

PostPosted: Mon Jan 21, 2013 9:49 am    Post subject: Reply with quote

hi bell. standard vlan ist ja kein problem. auf diesem board funktioniert das leider nicht so einfach. ;) sobald ich zu hause bin, versuche ich das problem besser zu beschreiben.
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Deutsches Forum (German) All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum