Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
Wireless: BCM4331 on a Macbook Pro 9,2
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Kernel & Hardware
View previous topic :: View next topic  
Author Message
spontz
n00b
n00b


Joined: 18 Nov 2012
Posts: 1

PostPosted: Sun Nov 18, 2012 6:29 pm    Post subject: Wireless: BCM4331 on a Macbook Pro 9,2 Reply with quote

Hello world!

I'm trying to run Gentoo on a new Macbook Proc 13" and I get troubles to get the wireless card recognized.

I followed this docs:
http://linuxwireless.org/en/users/Drivers/b43
http://en.gentoo-wiki.com/wiki/Broadcom_43xx

But the card don't care about the module...
Code:

    kopf ~ # modprobe b43
    kopf ~ # lspci -vnn -d 14e4:4331 -k
    02:00.0 Network controller [0280]: Broadcom Corporation BCM4331 802.11a/b/g/n [14e4:4331] (rev 02)
            Subsystem: Broadcom Corporation BCM4331 802.11a/b/g/n [14e4:4331]
            Flags: bus master, fast devsel, latency 0, IRQ 17
            Memory at a0600000 (64-bit, non-prefetchable) [size=16K]
            Capabilities: [40] Power Management version 3
            Capabilities: [58] Vendor Specific Information: Len=78 <?>
            Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
            Capabilities: [d0] Express Endpoint, MSI 00
            Capabilities: [100] Advanced Error Reporting
            Capabilities: [13c] Virtual Channel
            Capabilities: [160] Device Serial Number 00-00-00-ff-ff-00-00-00
            Capabilities: [16c] Power Budgeting <?>
            Kernel driver in use: bcma-pci-bridge
            Kernel modules: bcma


I use Genkernel, here the last config generated: http://pastebin.ca/2252752

I'm that it can work, but I don't found what I have missed, if someone have an idea :)
Back to top
View user's profile Send private message
DONAHUE
Watchman
Watchman


Joined: 09 Dec 2006
Posts: 6709
Location: Goose Creek SC

PostPosted: Sun Nov 18, 2012 9:52 pm    Post subject: Reply with quote

Code:
emerge linux-firmware

recommend menuconfig be:
Quote:
[*] Networking support --->
-*- Wireless --->
--- Wireless
<M> cfg80211 - wireless configuration API
[ ] nl80211 testmode command
[ ] enable developer warnings
[ ] cfg80211 regulatory debugging
[ ] enable powersave by default
[ ] cfg80211 DebugFS entries
[*] cfg80211 wireless extensions compatibility
< > Common routines for IEEE802.11 drivers
<M> Generic IEEE 802.11 Networking Stack (mac80211)
Default rate control algorithm (Minstrel) --->
[ ] Enable mac80211 mesh networking (pre-802.11s) support
[ ] Export mac80211 internals in DebugFS
[ ] Trace all mac80211 debug messages
[ ] Select mac80211 debugging features --->

<*> RF switch subsystem support --->

Device Drivers --->
[*] Network device support --->
[*] Wireless LAN --->
<M> Broadcom 43xx wireless support (mac80211 stack)
[ ] Support for 802.11n (N-PHY) devices (EXPERIMENTAL) (NEW)
[ ] Support for low-power (LP-PHY) devices (NEW)
[*] Support for HT-PHY (high throughput) devices (EXPERIMENTAL) (NEW)
[ ] Broadcom 43xx debugging (NEW)
< > Broadcom 43xx-legacy wireless support (mac80211 stack)
< > Broadcom IEEE802.11n embedded FullMAC WLAN driver

Broadcom specific AMBA --->
< > BCMA support


I don't have your NIC, but as I read the info available it is not 80211n capable and uses ssb bus not bcma and uses the ht-phy not N or lp.

If you follow this but still no luck check dmesg for clues.
_________________
Defund the FCC.
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Kernel & Hardware All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum