View previous topic :: View next topic |
Author |
Message |
Treborius Guru
Joined: 18 Oct 2005 Posts: 585 Location: Berlin
|
Posted: Sat Aug 11, 2012 12:13 am Post subject: Xorg seg-fault [solved] |
|
|
hallo, ich habe hier ein Problem mit X und komme nicht weiter
es geht um einen Geode LX,
X hat mal wunderbar funktioniert, nun bekomme ich es nichtmehr zum laufen
wenn ich versuche X zu starten bekomme ich folgende Fehlermeldung :
Code: |
AmdPciProbe: Probing for supported devices!
Unable to open /dev/cpu/0/msr: 2
Backtrace:
0: X (xorg_backtrace+0x50) [0xb78bc920]
Segmentation fault at address (nil)
Fatal server error:
Caught signal 11 (Segmentation fault). Server aborting
|
in der /var/log/Xorg.0.log steht eigentlich nix interessantes drin :
Code: |
[ 3618.831] (II) GEODE(0): Not using default mode "960x720" (vrefresh out of range)
[ 3618.831] (II) GEODE(0): Not using default mode "2048x1536" (height too large for virtual size)
[ 3618.831] (II) GEODE(0): Not using default mode "1024x768" (hsync out of range)
[ 3618.831] (II) GEODE(0): Not using default mode "2048x1536" (height too large for virtual size)
[ 3618.831] (II) GEODE(0): Not using default mode "1024x768" (vrefresh out of range)
[ 3618.831] (II) GEODE(0): Not using default mode "2048x1536" (height too large for virtual size)
[ 3618.831] (II) GEODE(0): Not using default mode "1024x768" (vrefresh out of range)
[ 3618.831] (II) GEODE(0): Printing probed modes for output default
[ 3618.831] (II) GEODE(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz d)
[ 3618.831] (II) GEODE(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz d)
[ 3618.831] (II) GEODE(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz d)
[ 3618.831] (II) GEODE(0): Modeline "512x384"x60.0 32.50 512 524 592 672 384 385 388 403 doublescan -hsync -vsync (48.4 kHz d)
[ 3618.831] (II) GEODE(0): Modeline "400x300"x60.3 20.00 400 420 484 528 300 300 302 314 doublescan +hsync +vsync (37.9 kHz d)
[ 3618.832] (II) GEODE(0): Modeline "320x240"x60.1 12.59 320 328 376 400 240 245 246 262 doublescan -hsync -vsync (31.5 kHz d)
[ 3618.832] (II) GEODE(0): Output default connected
[ 3618.832] (II) GEODE(0): Using fuzzy aspect match for initial modes
[ 3618.832] (II) GEODE(0): Output default using initial mode 1024x768
[ 3618.832] (II) GEODE(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 3618.832] (--) GEODE(0): Virtual size is 1024x1024 (pitch 0)
[ 3618.832] (**) GEODE(0): Default mode "1024x768": 65.0 MHz (scaled from 0.0 MHz), 48.4 kHz, 60.0 Hz
[ 3618.832] (II) GEODE(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz d)
[ 3618.832] (**) GEODE(0): Default mode "800x600": 40.0 MHz (scaled from 0.0 MHz), 37.9 kHz, 60.3 Hz
[ 3618.832] (II) GEODE(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz d)
[ 3618.832] (**) GEODE(0): Default mode "640x480": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 59.9 Hz
[ 3618.833] (II) GEODE(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz d)
[ 3618.833] (**) GEODE(0): Default mode "512x384": 32.5 MHz (scaled from 0.0 MHz), 48.4 kHz, 60.0 Hz (D)
[ 3618.833] (II) GEODE(0): Modeline "512x384"x60.0 32.50 512 524 592 672 384 385 388 403 doublescan -hsync -vsync (48.4 kHz d)
[ 3618.833] (**) GEODE(0): Default mode "400x300": 20.0 MHz (scaled from 0.0 MHz), 37.9 kHz, 60.3 Hz (D)
[ 3618.833] (II) GEODE(0): Modeline "400x300"x60.3 20.00 400 420 484 528 300 300 302 314 doublescan +hsync +vsync (37.9 kHz d)
[ 3618.833] (**) GEODE(0): Default mode "320x240": 12.6 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.1 Hz (D)
[ 3618.833] (II) GEODE(0): Modeline "320x240"x60.1 12.59 320 328 376 400 240 245 246 262 doublescan -hsync -vsync (31.5 kHz d)
[ 3618.833] (==) GEODE(0): DPI set to (96, 96)
[ 3618.833] (II) Loading sub module "fb"
[ 3618.833] (II) LoadModule: "fb"
[ 3618.834] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 3618.836] (II) Module fb: vendor="X.Org Foundation"
[ 3618.836] compiled for 1.12.2, module version = 1.0.0
[ 3618.836] ABI class: X.Org ANSI C Emulation, version 0.4
[ 3618.836] (II) Loading sub module "exa"
[ 3618.836] (II) LoadModule: "exa"
[ 3618.837] (II) Loading /usr/lib/xorg/modules/libexa.so
[ 3618.838] (II) Module exa: vendor="X.Org Foundation"
[ 3618.838] compiled for 1.12.2, module version = 2.5.0
[ 3618.838] ABI class: X.Org Video Driver, version 12.0
[ 3618.838] (II) UnloadModule: "vesa"
[ 3618.838] (II) Unloading vesa
[ 3618.838] (II) UnloadModule: "fbdev"
[ 3618.838] (II) Unloading fbdev
[ 3618.838] (II) UnloadSubModule: "fbdevhw"
[ 3618.838] (II) Unloading fbdevhw
[ 3618.839]
[ 3618.839] Backtrace:
[ 3618.840] 0: X (xorg_backtrace+0x50) [0xb78bc920]
[ 3618.840]
[ 3618.841] Segmentation fault at address (nil)
[ 3618.841]
Fatal server error:
[ 3618.841] Caught signal 11 (Segmentation fault). Server aborting
[ 3618.842]
[ 3618.842]
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 3618.842] Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 3618.843]
[ 3618.844] Server terminated with error (1). Closing log file.
|
Das sagt mir erstmal nur, das bis zum Segmentation fault alles wunderbar läuft,
ein strace auf die ganze Sache lieferte mir dann das
Code: |
open("/sys/class/pci_bus/0000:00/legacy_mem", O_RDWR|O_CLOEXEC) = -1 ENOENT (No such file or directory)
open("/dev/mem", O_RDWR|O_CLOEXEC) = 7
mmap2(NULL, 65536, PROT_READ|PROT_WRITE, MAP_SHARED, 7, 0xa0) = 0xb7009000
close(7) = 0
--- SIGSEGV {si_signo=SIGSEGV, si_code=SEGV_MAPERR, si_addr=0} ---
|
ich tippe ja darauf, das die datei "/sys/class/pci_bus/0000:00/legacy_mem" existieren sollte
(tut sie nämlich nicht) und ich irgendwas im kernel vergessen hab
jemand ne ahnung wie ich weiter vorgehen sollte? google hat mir irgendwie nix gebracht ...
Code: |
Portage 2.1.10.65 (hardened/linux/x86, gcc-4.5.3, glibc-2.14.1-r3, 3.0.6-gentoo-alix i586)
=================================================================
System uname: Linux-3.0.6-gentoo-alix-i586-Geode-TM-_Integrated_Processor_by_AMD_PCS-with-gentoo-2.1
Timestamp of tree: Tue, 07 Aug 2012 22:00:01 +0000
ccache version 3.1.7 [enabled]
app-shells/bash: 4.2_p20
dev-java/java-config: 2.1.11-r3
dev-lang/python: 2.7.3-r2, 3.1.4-r3, 3.2.3
dev-util/ccache: 3.1.7
dev-util/cmake: 2.8.7-r5
dev-util/pkgconfig: 0.26
sys-apps/baselayout: 2.1-r1
sys-apps/openrc: 0.9.8.4
sys-apps/sandbox: 2.5
sys-devel/autoconf: 2.68
sys-devel/automake: 1.11.1
sys-devel/binutils: 2.21.1-r1
sys-devel/gcc: 4.5.3-r2
sys-devel/gcc-config: 1.6
sys-devel/libtool: 2.4-r1
sys-devel/make: 3.82-r1
sys-kernel/linux-headers: 3.1 (virtual/os-headers)
sys-libs/glibc: 2.14.1-r3
Repositories: gentoo x-portage
ACCEPT_KEYWORDS="x86"
ACCEPT_LICENSE="* -@EULA"
CBUILD="i486-pc-linux-gnu"
CFLAGS="-march=native -O2 -pipe -fomit-frame-pointer"
CHOST="i486-pc-linux-gnu"
CONFIG_PROTECT="/etc /usr/share/openvpn/easy-rsa"
CONFIG_PROTECT_MASK="/etc/ca-certificates.conf /etc/env.d /etc/env.d/java/ /etc/fonts/fonts.conf /etc/gconf /etc/gentoo-
release /etc/php/apache2-php5.3/ext-active/ /etc/php/cgi-php5.3/ext-active/ /etc/php/cli-php5.3/ext-active/ /etc/revdep-
rebuild /etc/sandbox.d /etc/terminfo"
CXXFLAGS="-march=native -O2 -pipe -fomit-frame-pointer"
DISTDIR="/var/distfiles"
FCFLAGS="-march=i686 -O2 -pipe"
FEATURES="assume-digests binpkg-logs ccache config-protect-if-modified distlocks ebuild-locks fixlafiles news parallel-f
etch parse-eapi-ebuild-head protect-owned sandbox sfperms strict unknown-features-warn unmerge-logs unmerge-orphans user
fetch"
FFLAGS="-march=i686 -O2 -pipe"
GENTOO_MIRRORS="http://distfiles.gentoo.org"
LDFLAGS="-Wl,-O1 -Wl,--as-needed"
LINGUAS="de"
PKGDIR="/usr/portage/packages"
PORTAGE_CONFIGROOT="/"
PORTAGE_RSYNC_OPTS="--recursive --links --safe-links --perms --times --compress --force --whole-file --delete --stats --
human-readable --timeout=180 --exclude=/distfiles --exclude=/local --exclude=/packages"
PORTAGE_TMPDIR="/var/tmp"
PORTDIR="/var/portage"
PORTDIR_OVERLAY="/usr/local/portage"
SYNC="rsync://rsync.gentoo.org/gentoo-portage"
...
|
Vielleicht ist es ja ein total dummer denkfehler meinerseits
Danke im Vorraus
Treb _________________ Systems running gentoo :
Desktop, Laptop, ZOTAC AD-10 media-center, odroid-xu4 server / wLan-router
Last edited by Treborius on Mon Aug 13, 2012 6:03 am; edited 1 time in total |
|
Back to top |
|
|
Treborius Guru
Joined: 18 Oct 2005 Posts: 585 Location: Berlin
|
Posted: Mon Aug 13, 2012 6:03 am Post subject: |
|
|
bin erstmal auf vesa umgestiegen _________________ Systems running gentoo :
Desktop, Laptop, ZOTAC AD-10 media-center, odroid-xu4 server / wLan-router |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|