View previous topic :: View next topic |
Author |
Message |
kotviski n00b
Joined: 13 Feb 2010 Posts: 26
|
Posted: Wed Mar 24, 2010 2:35 pm Post subject: Wifi manager dont find any wireless network |
|
|
Hello everybody.
Im using wicd here to manage my wireless connections, but it isn't finding any.
Here is some information:
Code: | lspci | egrep Wireless
0b:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
|
Code: | cat /usr/src/linux/.config | grep 4965 && cat /usr/src/linux/.config | grep 802
CONFIG_IWL4965=y
# CONFIG_VLAN_8021Q is not set
# CONFIG_IEEE802154 is not set
CONFIG_CFG80211=y
# CONFIG_CFG80211_REG_DEBUG is not set
# CONFIG_CFG80211_DEBUGFS is not set
CONFIG_LIB80211=y
CONFIG_LIB80211_DEBUG=y
CONFIG_MAC80211=y
CONFIG_MAC80211_DEFAULT_PS=y
CONFIG_MAC80211_DEFAULT_PS_VALUE=1
CONFIG_MAC80211_RC_MINSTREL=y
# CONFIG_MAC80211_RC_DEFAULT_PID is not set
CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
CONFIG_MAC80211_RC_DEFAULT="minstrel"
CONFIG_MAC80211_LEDS=y
# CONFIG_MAC80211_DEBUGFS is not set
# CONFIG_MAC80211_DEBUG_MENU is not set
# CONFIG_WLAN_PRE80211 is not set
CONFIG_WLAN_80211=y
# CONFIG_MAC80211_HWSIM is not set
# CONFIG_LEDS_BD2802 is not set
# CONFIG_RTC_DRV_RX8025 is not set
# CONFIG_RTC_DRV_BQ4802 is not set |
Code: | cat /etc/conf.d/net
# This blank configuration will automatically use DHCP for any net.*
# scripts in /etc/init.d. To create a more complete configuration,
# please review /etc/conf.d/net.example and save your configuration
# in /etc/conf.d/net (this file :]!).
config_eth0=( "dhcp" )
modules=( "wpa_supplicant" )
wpa_supplicant_wlan0="-Dwext"
config_wlan0=( "dhcpcd" )
|
Code: | cat /etc/wpa_supplicant/wpa_supplicant.conf
# This is a network block that connects to any unsecured access point.
# We give it a low priority so any defined blocks are preferred.
# The below line not be changed otherwise we refuse to work
ctrl_interface=/var/run/wpa_supplicant
# Ensure that only root can read the WPA configuration
ctrl_interface_group=wheel
# Let wpa_supplicant take care of scanning and AP selection
ap_scan=1
|
Code: | wpa_supplicant -v
wpa_supplicant v0.6.9
Copyright (c) 2003-2009, Jouni Malinen <j@w1.fi> and contributors
|
Code: | /etc/init.d/net.wlan0 start
* WARNING: net.wlan0 has already been started.
|
Code: | ifconfig -a
eth0 Encapsulamento do Link: Ethernet Endereço de HW 00:1e:c9:fb:21:b9
inet end.: 192.168.0.184 Bcast:192.168.0.255 Masc:255.255.255.0
endereço inet6: fe80::21e:c9ff:fefb:21b9/64 Escopo:Link
UP BROADCASTRUNNING MULTICAST MTU:1500 Métrica:1
RX packets:341 errors:0 dropped:0 overruns:0 frame:0
TX packets:692 errors:0 dropped:0 overruns:0 carrier:0
colisões:0 txqueuelen:1000
RX bytes:118767 (115.9 KiB) TX bytes:77205 (75.3 KiB)
IRQ:16
lo Encapsulamento do Link: Loopback Local
inet end.: 127.0.0.1 Masc:255.0.0.0
endereço inet6: ::1/128 Escopo:Máquina
UP LOOPBACKRUNNING MTU:16436 Métrica:1
RX packets:644 errors:0 dropped:0 overruns:0 frame:0
TX packets:644 errors:0 dropped:0 overruns:0 carrier:0
colisões:0 txqueuelen:0
RX bytes:49212 (48.0 KiB) TX bytes:49212 (48.0 KiB)
sit0 Encapsulamento do Link: IPv6 sobre IPv4
NOARP MTU:1480 Métrica:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
colisões:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
wlan0 Encapsulamento do Link: Ethernet Endereço de HW 00:21:5c:4a:50:7b
UP BROADCASTMULTICAST MTU:1500 Métrica:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
colisões:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
wmaster0 Encapsulamento do Link: Não Especificado Endereço de HW 00-21-5C-4A-50-7B-00-00-00-00-00-00-00-00-00-00
UP RUNNING MTU:0 Métrica:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
colisões:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) |
Code: | iwconfig
lo no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11abgn ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=15 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
sit0 no wireless extensions.
eth0 no wireless extensions. |
Code: | wpa_cli status
Selected interface 'wlan0'
wpa_state=SCANNING
|
Code: | lsmod
Module Size Used by
fuse 50688 4
ohci1394 25496 0
ieee1394 66272 1 ohci1394
uvcvideo 50036 0
dcdbas 6548 0
pcspkr 2160 0
sky2 38748 0
btusb 10448 2
|
Code: | rc-update show
bootmisc | boot
checkfs | boot
checkroot | boot
clock | boot
consolefont | boot
dbus | default
hald | default
hostname | boot
keymaps | boot
local | default nonetwork
localmount | boot
modules | boot
net.eth0 | default
net.lo | boot
netmount | default
rmnologin | boot
syslog-ng | default
udev-postmount | default
urandom | boot
vixie-cron | default
wicd | default
xdm | default
|
Someone have any ideia about what is going wrong? |
|
Back to top |
|
|
audiodef Watchman
Joined: 06 Jul 2005 Posts: 6639 Location: The soundosphere
|
|
Back to top |
|
|
Raistlin Majere n00b
Joined: 04 Feb 2010 Posts: 61
|
Posted: Thu Mar 25, 2010 4:40 pm Post subject: |
|
|
Try getting rid of your network config's , Wicd handles all of this for you.
Try removing wpa_supplicant.conf and remove everything from /etc/conf.d/net.
Also remove any net.* symlinks in /etc/init.d , except for net.lo which you need
Then you can configure wicd with whatever setting you want , like dhcp, ect.. from the prefernces menu |
|
Back to top |
|
|
|