Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
Problem installing on Alpha ES40
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Gentoo on Alternative Architectures
View previous topic :: View next topic  
Author Message
O-Zone
n00b
n00b


Joined: 10 Jul 2008
Posts: 2

PostPosted: Thu Jul 10, 2008 11:58 am    Post subject: Problem installing on Alpha ES40 Reply with quote

Hi all,
i have problems installing Gentoo on an Alpha ES40. I think that the problem is disks on SmartRAID controller (I2O) and installation disks don't have support for i2o. Hardware is ok because there's an HPUX thats work perfectly.

Anyone can help me ?

Thanks, O-Zone

Here's lspci:

Quote:
livecd ~ # lspci
0000:00:01.0 VGA compatible controller: Texas Instruments TVP4020 [Permedia 2] (rev 01)
0000:00:07.0 ISA bridge: ALi Corporation M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/V+] (rev c3)
0000:00:0f.0 IDE interface: ALi Corporation M5229 IDE (rev c1)
0000:00:13.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
0001:01:01.0 SCSI storage controller: LSI Logic / Symbios Logic 53c895 (rev 02)
0001:01:04.0 PCI bridge: Digital Equipment Corporation DECchip 21154 (rev 02)
0001:01:06.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 08)
0001:02:03.0 Memory controller: Adaptec (formerly DPT) Domino RAID Engine (rev 02)
0001:02:04.0 I2O: Adaptec (formerly DPT) SmartRAID V Controller (rev 03)
livecd ~ #


...lsmod...

Quote:
livecd ~ # lsmod
Module Size Used by
e100 52032 0
tg3 155964 0
e1000 179380 0
nfs 204248 0
nfs_acl 7168 1 nfs
lockd 99840 1 nfs
sunrpc 264776 5 nfs,nfs_acl,lockd
jfs 236384 0
reiserfs 318076 0
ext3 174696 0
jbd 73432 1 ext3
raid10 33904 0
raid456 144040 0
async_tx 5400 1 raid456
async_memcpy 4568 1 raid456
async_xor 5816 1 raid456
xor 11704 2 raid456,async_xor
raid1 34272 0
raid0 12016 0
md_mod 107904 4 raid10,raid456,raid1,raid0
dm_snapshot 26608 0
dm_mirror 33540 0
dm_mod 86472 2 dm_snapshot,dm_mirror
sg 45264 0
scsi_wait_scan 3720 0
livecd ~ #


...and dmesg:

Quote:
Linux version 2.6.24-gentoo-r6 (root@monolith) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.2)) #1 SMP Sun May 18 13:53:20 UTC 2008
Booting GENERIC on Tsunami variation Clipper using machine vector Clipper from SRM
Major Options: SMP LEGACY_START VERBOSE_MCHECK MAGIC_SYSRQ
Command line: root=/dev/ram0 init=/linuxrc dokeymap looptype=squashfs loop=/image.squashfs cdroot
memcluster 0, usage 1, start 0, end 256
memcluster 1, usage 0, start 256, end 130986
memcluster 2, usage 1, start 130986, end 131072
memcluster 3, usage 0, start 131072, end 262142
memcluster 4, usage 1, start 262142, end 262144
freeing pages 256:384
freeing pages 1325:130986
freeing pages 131072:262142
reserving pages 1325:1329
Initial ramdisk at: 0xfffffc007fb32000 (2900984 bytes)
8192K Bcache detected; load hit latency 21 cycles, load miss latency 178 cycles
Console graphics on hose 0
SMP: 2 CPUs probed -- cpu_present_map = 3
On node 0 totalpages: 262142
DMA zone: 1791 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 260351 pages, LIFO batch:15
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260351
Kernel command line: root=/dev/ram0 init=/linuxrc dokeymap looptype=squashfs loop=/image.squashfs cdroot
PID hash table entries: 4096 (order: 12, 32768 bytes)
Using epoch = 1952
Turning on RTC interrupts.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 262144 (order: 8, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 7, 1048576 bytes)
Memory: 2063808k/2097136k available (5010k kernel code, 29992k reserved, 441k data, 400k init)
Calibrating delay loop... 1657.40 BogoMIPS (lpj=808960)
Mount-cache hash table entries: 512
SMP starting up secondaries.
Calibrating delay loop... 1657.40 BogoMIPS (lpj=808960)
Brought up 2 CPUs
SMP: Total of 2 processors activated (3320.05 BogoMIPS).
net_namespace: 120 bytes
NET: Registered protocol family 16
EISA bus registered
pci: enabling save/restore of SRM state
PCI: Bridge: 0001:01:04.0
IO window: 8000-8fff
MEM window: 09000000-092fffff
PREFETCH window: 0c000000-17ffffff
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 524288 bytes)
TCP established hash table entries: 262144 (order: 9, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
Unpacking initramfs... done
Freeing initrd memory: 2832k freed
squashfs: version 3.3 (2007/10/31) Phillip Lougher
SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered (default)
io scheduler cfq registered
Activating ISA DMA hang workarounds.
PCI: Firmware left 0001:01:06.0 e100 interrupts enabled, disabling
rtc: Digital UNIX epoch (1952) detected
Real Time Clock Driver v1.12ac
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 2.88M
FDC 0 is a post-1991 82077
loop: module loaded
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.14)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller (0x10b9:0x5229 rev 0xc1) at PCI slot 0000:00:0f.0
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8000-0x8007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x8008-0x800f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: Compaq CRD-8402B, ATAPI CD/DVD-ROM drive
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: MWDMA2 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
hda: ATAPI 40X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
Loading iSCSI transport class v2.0-724.
Adaptec aacraid driver 1.1-5[2449]-ms
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
scsi: <fdomain> Detection failed (no card)
NCR53c406a: no available ports found
sym53c416.c: Version 1.0.0-ac
qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver
iscsi: registered transport (qla4xxx)
QLogic iSCSI HBA Driver
sym0: <895> rev 0x2 at pci 0001:01:01.0 irq 40
sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.3
DC390: clustering now enabled by default. If you get problems load
with "disable_clustering=1" and report to maintainers
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.10-rc5 Thu May 17 10:09:32 PDT 2007
GDT-HA: Storage RAID Controller Driver. Version: 3.05
GDT-HA: Found 0 PCI Storage RAID Controllers
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.010.
RocketRAID 3xxx SATA Controller driver v1.2 (070830)
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
Fusion MPT base driver 3.04.06
Copyright (c) 1999-2007 LSI Corporation
Fusion MPT SPI Host driver 3.04.06
Fusion MPT FC Host driver 3.04.06
Fusion MPT SAS Host driver 3.04.06
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 10, io mem 0x0a030000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
USB Universal Host Controller Interface driver v3.0
drivers/usb/host/r8a66597-hcd.c: driver r8a66597_hcd, 29 May 2007
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Freeing unused kernel memory: 400k freed
input: PS/2 Logitech Mouse as /class/input/input1
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: alpha prefetch
alpha prefetch: 3481.600 MB/sec
xor: using function: alpha prefetch (3481.600 MB/sec)
async_tx: api initialized (sync-only)
raid6: int64x1 824 MB/s
raid6: int64x2 1088 MB/s
raid6: int64x4 1244 MB/s
raid6: int64x8 796 MB/s
raid6: using algorithm int64x4 (1244 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
JFS: nTxBlock = 8076, nTxLock = 64614
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
warning: process `hwsetup' used the deprecated sysctl system call with 1.23.
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100: eth0: e100_probe: addr 0x209521000, irq 60, MAC addr 00:50:8b:ae:d3:b2
warning: process `hwsetup' used the deprecated sysctl system call with 1.49.
warning: process `hwsetup' used the deprecated sysctl system call with 1.49.
hda: MWDMA2 mode selected
Back to top
View user's profile Send private message
alex.blackbit
Advocate
Advocate


Joined: 26 Jul 2005
Posts: 2396

PostPosted: Thu Jul 10, 2008 12:07 pm    Post subject: Reply with quote

according to your dmesg output you do not get devices for your storage, right?
check the driver compatibility of your controller in the kernel docs.
Back to top
View user's profile Send private message
O-Zone
n00b
n00b


Joined: 10 Jul 2008
Posts: 2

PostPosted: Thu Jul 10, 2008 12:10 pm    Post subject: Reply with quote

alex.blackbit wrote:
according to your dmesg output you do not get devices for your storage, right?
check the driver compatibility of your controller in the kernel docs.


Yes, right. I cannot install because i don't get the disks ! I think the problem is with that I2O controller but i need the kernel module to check.

Thanks for reply, O-Zone
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Gentoo on Alternative Architectures All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum