| View previous topic :: View next topic |
| Author |
Message |
sick6oy
n00b
Joined: 18 Sep 2007
Posts: 22
|
 Posted: Wed Oct 03, 2007 6:45 pm Post subject: Problem z eth1 |
 |
|
Witam.
Podczas ladowania systemu pojawia mi sie cos takiego :
* Starting eth1
* Bringing up eth1
* dhcp
* network interface eth1 does not exist
* Please verify hardware or kernel module (driver)
* ERROR: cannot start netmount as net.eth1 could not start
Ma ktos jakis pomysl jak rozwiazac ten problem ?
Z gory dziekuje za pomoc.  |
|
| Back to top |
|
 |
mistix
Apprentice
Joined: 27 Dec 2006
Posts: 248
Location: Gliwice / Poland
|
| Posted: Wed Oct 03, 2007 7:41 pm Post subject: |
|
|
Sprawdź na początek czy moduły odpowiedzialne za eth1 (o ile masz drugą kartę sieciową) istnieją. A jak nie istnieją to wywal net.eth1 ze startu systemu.
_________________
Cuda się zdarzają. Co potwierdzi każdy programista. |
|
| Back to top |
|
|
sick6oy
n00b
Joined: 18 Sep 2007
Posts: 22
|
| Posted: Wed Oct 03, 2007 7:42 pm Post subject: |
|
|
| A jakie to moduly i jak je sprawdzic ? |
|
| Back to top |
|
|
mistix
Apprentice
Joined: 27 Dec 2006
Posts: 248
Location: Gliwice / Poland
|
| Posted: Wed Oct 03, 2007 7:44 pm Post subject: |
|
|
To może na początek pokaż wynik lspci bo ciężko stwierdzić co to za karta.
_________________
Cuda się zdarzają. Co potwierdzi każdy programista. |
|
| Back to top |
|
|
sick6oy
n00b
Joined: 18 Sep 2007
Posts: 22
|
| Posted: Wed Oct 03, 2007 8:47 pm Post subject: |
|
|
Oto co pokazalo lspci :
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 760/M760 Host (rev 03)
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] SG86C202
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS963 [MuTIOL Media IO] (rev 25)
00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus Controller
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE]
00:02.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem Controller (rev a0)
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] AC'97 Sound Controller (rev a0)
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f)
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f)
00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 91)
00:06.0 CardBus bridge: Texas Instruments PCI1510 PC card Cardbus Controller
00:0b.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 661/741/760/761 PCI/AGP VGA Display Adapter
Jakies pomysly  ? |
|
| Back to top |
|
|
Zwierzak
Veteran
Joined: 19 Sep 2003
Posts: 1012
Location: /dev/null
|
| Posted: Wed Oct 03, 2007 9:59 pm Post subject: |
|
|
| Numerowanie eth zaczyna się od 0, a nie od 1 |
|
| Back to top |
|
|
sick6oy
n00b
Joined: 18 Sep 2007
Posts: 22
|
| Posted: Thu Oct 04, 2007 6:21 am Post subject: |
|
|
| Tak, zaczyna sie od zera ale u mnie nr 0 podczas instalacji mialo wi-fi a zwykla sieciowka posiadala wlasnie nr 1. Internet podczas instalacji dzialal bez problemu. |
|
| Back to top |
|
|
Bialy
Guru
Joined: 20 Mar 2006
Posts: 471
|
| Posted: Thu Oct 04, 2007 6:29 am Post subject: |
|
|
| sick6oy wrote: | | Tak, zaczyna sie od zera ale u mnie nr 0 podczas instalacji mialo wi-fi a zwykla sieciowka posiadala wlasnie nr 1. Internet podczas instalacji dzialal bez problemu. |
wifi mialo eth0 czy wifi0?
Pokaz iwconfig i ifconfig |
|
| Back to top |
|
|
sick6oy
n00b
Joined: 18 Sep 2007
Posts: 22
|
| Posted: Thu Oct 04, 2007 7:48 am Post subject: |
|
|
Wifi mialo eth0 w net-setupie eht1 miala zwykla sieciowka. Nie mam niczego takiego jak iwconfig chyba ze gdzies jest ukryte a ja nie znam sciezki.
Oto zawartosc ifconfiga :
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) |
|
| Back to top |
|
|
Bialy
Guru
Joined: 20 Mar 2006
Posts: 471
|
| Posted: Thu Oct 04, 2007 8:48 am Post subject: |
|
|
| iwconfig to polecenie. |
|
| Back to top |
|
|
sick6oy
n00b
Joined: 18 Sep 2007
Posts: 22
|
| Posted: Thu Oct 04, 2007 8:52 am Post subject: |
|
|
| No tak tez myslalem ale nie dziala, jakby go nie bylo. |
|
| Back to top |
|
|
Bialy
Guru
Joined: 20 Mar 2006
Posts: 471
|
| Posted: Thu Oct 04, 2007 9:03 am Post subject: |
|
|
| Sprobuj zmienic nazwe z eth1 na eth0 w /etc/init.d |
|
| Back to top |
|
|
sick6oy
n00b
Joined: 18 Sep 2007
Posts: 22
|
| Posted: Thu Oct 04, 2007 9:52 am Post subject: |
|
|
Oto zawartosc katalogu /etc/init.d
bootmisc
checkfs
checkroot
clock
consolefont
crypto-loop
depscan.sh
functions.sh
gpm
halt.sh
hdparm
hostname
initd.txt
keymaps
local
localmount
modules
net.eth0
net.eth1
net.lo
netmount
nscd
numlock
reboot.sh
rmnologin
rsyncd
runscript.sh
shutdown.sh
sshd
syslog-ng
urandom
vixie-cron |
|
| Back to top |
|
|
SlashBeast
Moderator
Joined: 23 May 2006
Posts: 2722
|
| Posted: Thu Oct 04, 2007 10:04 am Post subject: |
|
|
Udev może zmieniać sieciówkę z eth0 na eth1, jak pozbyłem się pseudo sieci realteka to forcedeth zawsze występował jako eth1, dopiero jak w /etc/udev zmieniłem by nie zmieniało nazwy to przeszło. ifconfig -a wyświetli wszystkie sieci jakie masz.
_________________
github |
|
| Back to top |
|
|
sick6oy
n00b
Joined: 18 Sep 2007
Posts: 22
|
| Posted: Thu Oct 04, 2007 10:17 am Post subject: |
|
|
Witaj SlashBeast
Oto zawartosc ifconfiga z parametrem a :
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) |
|
| Back to top |
|
|
SlashBeast
Moderator
Joined: 23 May 2006
Posts: 2722
|
| Posted: Thu Oct 04, 2007 10:23 am Post subject: |
|
|
Wkompiluj w kernel SiS 900/7016 PCI Fast Ethernet Adapter support i SiS190/SiS191 gigabit ethernet support.
_________________
github |
|
| Back to top |
|
|
sick6oy
n00b
Joined: 18 Sep 2007
Posts: 22
|
| Posted: Thu Oct 04, 2007 10:57 am Post subject: |
|
|
| Ok. Dzieki to bylo to, brakowalo SiSa w jadrze |
|
| Back to top |
|
|
|
Polskie forum (Polish) 
