| View previous topic :: View next topic |
| Author |
Message |
snIP3r
l33t
Joined: 21 May 2004
Posts: 853
Location: germany
|
 Posted: Fri May 11, 2007 12:06 pm Post subject: 2007.0 Server Profile Issue [solved] |
 |
|
Hi all!
i recently updated to the 2007.0 server profile. but from now on if i do an e.g. "emerge -uavD world" i get this message:
| Code: |
* This profile has not been tested thoroughly and is not considered to be
* a supported server profile at this time. For a supported server
* profile, please check the Hardened project (http://hardened.gentoo.org).
* This profile is merely a convenience for people who require a more
* minimal profile, yet are unable to use hardened due to restrictions in
* the software being used on the server. This profile should also be used
* if you require GCC 4.1 or Glibc 2.4 support. If you don't know if this
* applies to you, then it doesn't and you should probably be using
* Hardened, instead.
|
the profile is only a set of USE-flags so i think and hope it's ok choosing this profile for my homeserver?!?! or am i not???
hope someone could give me advise...
thx
snIP3r
_________________
Intel i3-4130T on ASUS P9D-X
Kernel 5.15.88-gentoo SMP
-----------------------------------------------
if your problem is fixed please add something like [solved] to the topic!
Last edited by snIP3r on Sat May 12, 2007 12:29 pm; edited 1 time in total |
|
| Back to top |
|
 |
neysx
Retired Dev
Joined: 27 Jan 2003
Posts: 795
|
| Posted: Fri May 11, 2007 1:16 pm Post subject: |
|
|
As you said, that profile is nothing but a couple of USE flags (USE="apache2 ldap mailwrapper mysql snmp truetype xml") and is utterly useless.
If security is an issue, do use a hardened profile.
If it isn't much of an issue for your home server, use the 2007.0/ basic profile and add/remove what you really need.
Hth |
|
| Back to top |
|
|
carpman
Advocate
Joined: 20 Jun 2002
Posts: 2202
Location: London - UK
|
| Posted: Sat May 12, 2007 9:40 am Post subject: Re: 2007.0 Server Profile Issue |
|
|
| snIP3r wrote: | Hi all!
i recently updated to the 2007.0 server profile. but from now on if i do an e.g. "emerge -uavD world" i get this message:
| Code: |
* This profile has not been tested thoroughly and is not considered to be
* a supported server profile at this time. For a supported server
* profile, please check the Hardened project (http://hardened.gentoo.org).
* This profile is merely a convenience for people who require a more
* minimal profile, yet are unable to use hardened due to restrictions in
* the software being used on the server. This profile should also be used
* if you require GCC 4.1 or Glibc 2.4 support. If you don't know if this
* applies to you, then it doesn't and you should probably be using
* Hardened, instead.
|
the profile is only a set of USE-flags so i think and hope it's ok choosing this profile for my homeserver?!?! or am i not???
hope someone could give me advise...
thx
snIP3r |
There is an option you can add to make.conf to make this message go away, can't remember what it is and don't have access to box that uses it, will post it later.
_________________
Work Station - 64bit
Gigabyte GA X48-DQ6 Core2duo E8400
8GB GSkill DDR2-1066
SATA Areca 1210 Raid
BFG OC2 8800 GTS 640mb
--------------------------------
Notebook
Samsung Q45 7100 4gb |
|
| Back to top |
|
|
Polynomial-C
Retired Dev
Joined: 01 Jun 2003
Posts: 1432
Location: Germany
|
| Posted: Sat May 12, 2007 11:48 am Post subject: |
|
|
This must go into /etc/make.conf to get rid of that message: | Code: | | I_KNOW_WHAT_I_AM_DOING="yes" |
And no, I'm not kidding 
_________________
The manual said "Requires Windows10 or better" so I installed GNU/Linux...
my portage overlay
Need a stage1 tarball? (Unofficial builds) |
|
| Back to top |
|
|
snIP3r
l33t
Joined: 21 May 2004
Posts: 853
Location: germany
|
| Posted: Sat May 12, 2007 12:29 pm Post subject: |
|
|
| Polynomial-C wrote: | This must go into /etc/make.conf to get rid of that message: | Code: | | I_KNOW_WHAT_I_AM_DOING="yes" |
And no, I'm not kidding |
hi Polynomial-C!
thx for the help. this fixed my issue  i think i should check possible settings for make.conf
greets
snIP3r
_________________
Intel i3-4130T on ASUS P9D-X
Kernel 5.15.88-gentoo SMP
-----------------------------------------------
if your problem is fixed please add something like [solved] to the topic! |
|
| Back to top |
|
|
|
Portage & Programming
