Thanks again
Code: Select all
mount
/dev/hda3 on / type ext3 (rw)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec)
udev on /dev type tmpfs (rw,nosuid)
devpts on /dev/pts type devpts (rw,nosuid,noexec)
/dev/hda1 on /boot type ext2 (rw)
none on /dev/shm type tmpfs (rw)
usbfs on /proc/bus/usb type usbfs (rw,noexec,nosuid,devmode=0664,devgid=85)
from my kernel config
Code: Select all
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
CONFIG_EXT2_FS_SECURITY=y
CONFIG_EXT2_FS_XIP=y
CONFIG_FS_XIP=y
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
# CONFIG_REISERFS_FS_XATTR is not set
CONFIG_JFS_FS=m
# CONFIG_JFS_POSIX_ACL is not set
# CONFIG_JFS_SECURITY is not set
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
CONFIG_FS_POSIX_ACL=y
CONFIG_XFS_FS=m
# CONFIG_XFS_QUOTA is not set
# CONFIG_XFS_SECURITY is not set
# CONFIG_XFS_POSIX_ACL is not set
# CONFIG_XFS_RT is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
# CONFIG_INOTIFY is not set
CONFIG_QUOTA=y
# CONFIG_QFMT_V1 is not set
# CONFIG_QFMT_V2 is not set
CONFIG_QUOTACTL=y
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
&
Code: Select all
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set
I think these have been set I am on my fith try. All just to get wireless working.
this seems to be making my problem worse because after the last time or two lspci no longer sees the wifi card like it used to.
Before my lspci said
Code: Select all
01:08.0 Ethernet controller: Intel Corporation 82801DB PRO/100 VE (MOB) Ethernet Controller (rev 83)
01:0b.0 CardBus bridge: Toshiba America Info Systems ToPIC100 PCI to Cardbus Bridge with ZV Support (rev 33)
02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03)
lapcat turtle # ndiswrapper -d 02:00.0 driver
'02:00.0' is not a valid device ID
now
After
Code: Select all
01:08.0 Ethernet controller: Intel Corporation 82801DB PRO/100 VE (MOB) Ethernet Controller (rev 83)
01:0b.0 CardBus bridge: Toshiba America Info Systems ToPIC100 PCI to Cardbus Bridge with ZV Support (rev 33)
It definitly does not see the card anymore.
I viewed the lsmod from before and after in xxdiff and ther is no difference in the loaded modules, I have updated world a few times.
Although the invalid device id was weird, before ndiswrapper said hardware detected and it says that no longer.
Obviously this is all from my kernel that the GUI installer made that did not contain a .config file that I can find (not saying much) but other wise works perfectly.
output of ndiswrapper before
Code: Select all
lapcat turtle # ndiswrapper -l
Installed ndis drivers:
mrv8000c driver present, hardware present
mrv8000c.sys invalid driver!
lapcat turtle # ndiswrapper -m
modprobe config already contains alias directive
After
Code: Select all
ndiswrapper -l
Installed ndis drivers:
mrv8000c driver present
I tryed a
and it showed hot plug starting not stopping first so I added it to the default run level too. then dmedg says
Code: Select all
pcmcia: Detected deprecated PCMCIA ioctl usage from process: cardmgr.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x1e0-0x1e7 0x4d0-0x4d7
cs: IO port probe 0xa00-0xaff: clean.
The working GUI installer kernel complaiiins about not seeing modules acpi.ko and shuch on start up and the fourth kernel did not even panic it just froze here:
Code: Select all
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
so this time I selected all the items the working kernel complains about and compiled them as modules so I can hopefully save them for the working GUI installer kernel. Where should I save them? or is where they are O.K?
However maby the GUI installer compiled in APCI because here it looks like it is running but it cant figure out the card:
Code: Select all
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 4 of device 0000:00:1d.0
PCI: Cannot allocate resource region 4 of device 0000:00:1d.1
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bus 2, cardbus bridge: 0000:01:0b.0
IO window: 0000c000-0000c0ff
IO window: 0000c400-0000c4ff
PREFETCH window: 28000000-29ffffff
MEM window: 2c000000-2dffffff
PCI: Bridge: 0000:00:1e.0
IO window: c000-cfff
MEM window: cff00000-cfffffff
PREFETCH window: 28000000-29ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:01:0b.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 18 (level, low) -> IRQ 16
This is getting complated.
but i googled all those words and I still am not shure. I dont think I need anything other than ext2 and ext3. 