| View previous topic :: View next topic |
| Author |
Message |
hiroki
Guru
Joined: 29 Jul 2003
Posts: 327
Location: @home in germany
|
 Posted: Fri Mar 03, 2006 9:37 am Post subject: "kernel BUG" when stopping xdm? (only with ati-dri |
 |
|
Hi,
I have a problem with the ATI-drivers (8.22.5). I am using xorg-x11-7.0-r1. I have an ATI Radeon Mobility 9600.
I have two configurations:
- using the ati-drivers (fglrx)
- using the xorg-x11-driver radeon (r300)
When using the ATI-drivers/fglrx I can start X (xdm) only once. As soon as I stop xdm, I get the following "kernel BUG" message:
| Quote: | ------------[ cut here ]------------
kernel BUG at <bad filename>:16105!
invalid operand: 0000 [#1]
PREEMPT
Modules linked in: rfcomm l2cap usbhid hci_usb bluetooth fglrx agpgart ipw2100 ieee80211 ieee80211_crypt firmware_class ehci_hcd uhci_hcd usbcore
CPU: 0
EIP: 0060:[<c01163b5>] Tainted: PF VLI
EFLAGS: 00010082 (2.6.15-gentoo-r5)
EIP is at __change_page_attr+0x135/0x1b0
eax: 00008e20 ebx: 2c740000 ecx: c1008e20 edx: 2c4001e3
esi: c0471ec4 edi: c1000000 ebp: 00000163 esp: e9c95e70
ds: 007b es: 007b ss: 0068
Process X (pid: 7756, threadinfo=e9c94000 task=ee461540)
Stack: ec740000 ec73f000 2c4001e3 ec740000 c158e800 00000040 00000000 00000246
c0116470 c158e800 00000163 ee3323e0 f1400000 00000006 00001000 c011606c
c158e000 00000041 00000163 c1000000 00000000 f1baf61b f1400000 00000040
Call Trace:
[<c0116470>] change_page_attr+0x40/0x80
[<c011606c>] iounmap+0x10c/0x130
[<f1baf61b>] agp_generic_free_gatt_table+0x6b/0xe0 [fglrx]
[<f1bb723f>] agp_backend_cleanup+0xf/0x60 [fglrx]
[<f1bb7290>] agp_power+0x0/0x30 [fglrx]
[<f1bbb817>] __ke_agp_uninit+0x17/0x20 [fglrx]
[<f1bc3e55>] _firegl_release_agp+0x15/0x140 [fglrx]
[<f1bc6695>] firegl_takedown+0x335/0xc40 [fglrx]
[<c0152e5b>] __handle_mm_fault+0x22b/0x280
[<f1bc59ef>] firegl_release+0x12f/0x190 [fglrx]
[<c016327a>] __fput+0x13a/0x170
[<c0161626>] filp_close+0x46/0x90
[<c01616da>] sys_close+0x6a/0xc0
[<c010315b>] sysenter_past_esp+0x54/0x75
Code: 09 d0 89 44 24 08 8b 44 24 0c 89 44 24 04 e8 73 fe ff ff 89 d9 e9 46 ff ff ff 80 3e 00 78 0c 09 eb 89 1e ff 49 04 e9 45 ff ff ff <0f> 0b e9 3e ff ff ff 8b 15 70 50
3e c0 8d 41 18 89 42 04 89 51
<6>note: X[7756] exited with preempt_count 2 |
But I can still work on the terminal. But as soon as I try to start X (xdm) again, my computer freezes, showing the terminal. I have to turn off the laptop and turn it on again.
If I use the xorg-driver (radeon/r300) I have no problems at all, I can stop and start X/xdm as often as I want, no problem.
Oh yeah, something else: if I try to unload the fglrx module (when X (xdm) is stopped) then the laptop freezes, too. Need to reboot then.
So my question is: why is that? And how can I fix it? I absolutely have no idea 
| Code: | Section "dri"
Mode 0666
EndSection
Section "Module"
Load "dbe" # Double buffer extension
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
Load "type1"
Load "freetype"
Load "glx" # libglx.a
Load "dri" # libdri.a
EndSection
Section "Files"
FontPath "/usr/share/fonts/local/"
FontPath "/usr/share/fonts/misc/"
FontPath "/usr/share/fonts/75dpi/:unscaled"
FontPath "/usr/share/fonts/100dpi/:unscaled"
FontPath "/usr/share/fonts/Type1/"
FontPath "/usr/share/fonts/75dpi/"
FontPath "/usr/share/fonts/100dpi/"
EndSection
Section "ServerFlags"
EndSection
Section "InputDevice"
Identifier "Keyboard1"
Driver "kbd"
Option "AutoRepeat" "500 30"
Option "XkbModel" "pc105"
#Option "XkbVariant" "nodeadkeys"
Option "XkbLayout" "de"
EndSection
Section "InputDevice"
Identifier "Touchpad"
Driver "synaptics"
Option "Protocol" "auto-dev"
Option "Device" "/dev/input/event1"
Option "Emulate3Buttons"
Option "LeftEdge" "1700"
Option "RightEdge" "5300"
Option "TopEdge" "1700"
Option "BottomEdge" "4200"
Option "FingerLow" "25"
Option "FingerHigh" "30"
Option "MaxTapTime" "180"
Option "MaxTapMove" "220"
Option "VertScrollDelta" "100"
Option "MinSpeed" "0.09"
Option "MaxSpeed" "0.18"
Option "AccelFactor" "0.0015"
Option "SHMConfig" "on"
EndSection
Section "InputDevice"
Identifier "USBmouse"
Driver "mouse"
Option "Protocol" "ExplorerPS/2"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5"
Option "SendCoreEvents" "true"
EndSection
Section "Monitor"
Identifier "Monitor0"
HorizSync 31.5 - 91.1
VertRefresh 60 - 100
Option "DPMS"
EndSection
Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"
Driver "vga"
EndSection
Section "Device"
Identifier "ATI Graphics Adapter"
Driver "fglrx"
# ### generic DRI settings ###
# === disable PnP Monitor ===
#Option "NoDDC"
# === disable/enable XAA/DRI ===
Option "no_accel" "no"
Option "no_dri" "no"
# === misc DRI settings ===
Option "mtrr" "off" # disable DRI mtrr mapper, driver has its own code for mtrr
# ### FireGL DDX driver module specific settings ###
# === Screen Management ===
Option "DesktopSetup" "0x00000100"
Option "MonitorLayout" "AUTO, NONE"
Option "IgnoreEDID" "off"
Option "HSync2" "unspecified"
Option "VRefresh2" "unspecified"
Option "ScreenOverlap" "0"
# === TV-out Management ===
Option "NoTV" "no"
Option "TVStandard" "NTSC-M"
Option "TVHSizeAdj" "0"
Option "TVVSizeAdj" "0"
Option "TVHPosAdj" "0"
Option "TVVPosAdj" "0"
Option "TVHStartAdj" "0"
Option "TVColorAdj" "0"
Option "GammaCorrectionI" "0x06419064"
Option "GammaCorrectionII" "0x00b02c0b"
# === OpenGL specific profiles/settings ===
Option "Capabilities" "0x00000000"
# === Video Overlay for the Xv extension ===
Option "VideoOverlay" "on"
# === OpenGL Overlay ===
# Note: When OpenGL Overlay is enabled, Video Overlay
# will be disabled automatically
Option "OpenGLOverlay" "off"
# === Center Mode (Laptops only) ===
Option "CenterMode" "off"
# === Pseudo Color Visuals (8-bit visuals) ===
Option "PseudoColorVisuals" "off"
# === QBS Management ===
Option "Stereo" "off"
Option "StereoSyncEnable" "1"
# === FSAA Management ===
Option "FSAAEnable" "no"
Option "FSAAScale" "1"
Option "FSAADisableGamma" "no"
Option "FSAACustomizeMSPos" "no"
Option "FSAAMSPosX0" "0.000000"
Option "FSAAMSPosY0" "0.000000"
Option "FSAAMSPosX1" "0.000000"
Option "FSAAMSPosY1" "0.000000"
Option "FSAAMSPosX2" "0.000000"
Option "FSAAMSPosY2" "0.000000"
Option "FSAAMSPosX3" "0.000000"
Option "FSAAMSPosY3" "0.000000"
Option "FSAAMSPosX4" "0.000000"
Option "FSAAMSPosY4" "0.000000"
Option "FSAAMSPosX5" "0.000000"
Option "FSAAMSPosY5" "0.000000"
# === Misc Options ===
Option "UseFastTLS" "0"
Option "BlockSignalsOnLock" "on"
Option "UseInternalAGPGART" "yes"
Option "ForceGenericCPU" "no"
BusID "PCI:1:0:0" # vendor=1002, device=4e50
Screen 0
EndSection
Section "Device"
Identifier "ATI r300"
Driver "radeon"
Option "AGPMode" "4"
Option "RenderAccel" "on"
# This two lines are needed to prevent fonts from being scrambled
Option "XaaNoScanlineImageWriteRect"
Option "XaaNoScanlineCPUToScreenColorExpandFill"
# Misc
BusID "PCI:1:0:0"
Screen 0
Option "UseInternalAGPGART" "true"
EndSection
Section "Screen"
Identifier "Screen0"
#Device "ATI Graphics Adapter"
Device "ATI r300"
Monitor "Monitor0"
DefaultDepth 24
#Option "backingstore"
Subsection "Display"
Depth 24
Modes "1400x1050"
ViewPort 0 0 # initial origin if mode is smaller than desktop
EndSubsection
EndSection
#Section "Extensions"
# Option "Composite" "Enable"
#EndSection
Section "ServerLayout"
# The Identifier line must be present
Identifier "Server Layout"
# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.
Screen "Screen0"
# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".
InputDevice "Touchpad" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
InputDevice "USBmouse" "SendCoreEvents"
EndSection
### EOF ### |
|
|
| Back to top |
|
 |
Luy
n00b
Joined: 22 Feb 2006
Posts: 4
|
| Posted: Fri Mar 03, 2006 10:03 pm Post subject: |
|
|
My computer has a Ati Radeon video board. and I have no problem with it. Exploring your xorg.conf you ar using a strange video adapter "fglrx" (try ati) . My sugestion is to try my configuration (in this part)
| Code: |
# $XdotOrg: xc/programs/Xserver/hw/xfree86/xorgconf.cpp,v 1.2 2004/04/23 19:20:02 eich Exp $
#
# Copyright (c) 1994-1998 by The XFree86 Project, Inc.
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
# THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# SOFTWARE.
#
# Except as contained in this notice, the name of the XFree86 Project shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from the
# XFree86 Project.
#
# $XConsortium: XF86Conf.cpp /main/22 1996/10/23 11:43:51 kaleb $
# **********************************************************************
# This is a sample configuration file only, intended to illustrate
# what a config file might look like. Refer to the XF86Config(4/5)
# man page for details about the format of this file. This man page
# is installed as /usr/share/man/man5/xorg.conf.5x
# **********************************************************************
# The ordering of sections is not important in version 4.0 and later.
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
# For XFS, uncomment this and comment the others
# FontPath "unix/:-1"
FontPath "/usr/share/fonts/local/"
FontPath "/usr/share/fonts/misc/"
FontPath "/usr/share/fonts/75dpi/:unscaled"
FontPath "/usr/share/fonts/100dpi/:unscaled"
FontPath "/usr/share/fonts/Type1/"
FontPath "/usr/share/fonts/TTF/"
FontPath "/usr/share/fonts/CID/"
FontPath "/usr/share/fonts/75dpi/"
FontPath "/usr/share/fonts/100dpi/"
# ModulePath can be used to set a search path for the X server modules.
# The default path is shown here.
# ModulePath "/usr/lib/modules"
EndSection
# **********************************************************************
# Module section -- this is an optional section which is used to specify
# which run-time loadable modules to load when the X server starts up.
# **********************************************************************
Section "Module"
# This loads the DBE extension module.
Load "dbe"
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga"
EndSubSection
# This loads the Type1 and FreeType font modules
Load "type1"
Load "freetype"
# This loads other modules
Load "synaptics"
EndSection
# **********************************************************************
# Server flags section. This contains various server-wide Options.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging
# Option "NoTrapSignals"
# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.
# Option "DontVTSwitch"
# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.
# Option "DontZap"
# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.
# Option "DontZoom"
# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.
# Option "DisableVidModeExtension"
# Uncomment this to enable the use of a non-local xvidtune client.
# Option "AllowNonLocalXvidtune"
# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.
#Option "DisableModInDev"
# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).
# Option "AllowNonLocalModInDev"
# Set the basic blanking screen saver timeout.
#Option "blank time" "10" # 10 minutes
# Set the DPMS timeouts. These are set here because they are global
# rather than screen-specific. These settings alone don't enable DPMS.
# It is enabled per-screen (or per-monitor), and even then only when
# the driver supports it.
#Option "standby time" "20"
#Option "suspend time" "30"
#Option "off time" "60"
# On some platform the server needs to estimate the sizes of PCI
# memory and pio ranges. This is done by assuming that PCI ranges
# don't overlap. Some broken BIOSes tend to set ranges of inactive
# devices wrong. Here one can adjust how aggressive the assumptions
# should be. Default is 0.
# Option "EstimateSizesAggresively" "0"
EndSection
# **********************************************************************
# Input devices
# **********************************************************************
# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************
Section "InputDevice"
Identifier "AT Translated Set 2 keyboard"
Driver "keyboard"
# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris), comment
# out the above line, and uncomment the following line.
# Option "Protocol" "Xqueue"
# Set the keyboard auto repeat parameters. Not all platforms implement
# this.
#Option "AutoRepeat" "500 5"
# Specifiy which keyboard LEDs can be user-controlled (eg, with xset(1)).
# Option "Xleds" "1 2 3"
# To disable the XKEYBOARD extension, uncomment XkbDisable.
# Option "XkbDisable"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a European
# keyboard, you will probably want to use one of:
#
# Option "XkbModel" "pc102"
# Option "XkbModel" "pc105"
#
# If you have a Microsoft Natural keyboard, you can use:
#
# Option "XkbModel" "microsoft"
#
# If you have a US "windows" keyboard you will want:
#
# Option "XkbModel" "pc104"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#
# Option "XkbLayout" "de"
#
# or:
#
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#
# Option "XkbOptions" "ctrl:swapcaps"
# These are the settings for xorg
#
#Option "CoreKeyboard"
#Option "Xkbrules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "br"
Option "XkbVariant" "us_intl"
Option "XkbOptions" ""
EndSection
Section "InputDevice"
Identifier "Sony Vaio Keys"
Driver "kbd"
Option "Protocol" "evdev"
Option "Dev Name" "Sony Vaio Keys"
Option "XkbModel" "pc105"
Option "XkbLayout" "br"
Option "XkbVariant" "us_intl"
Option "XkbOptions" ""
EndSection
# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************
Section "InputDevice"
# Identifier and driver
Identifier "PS/2 Mouse"
Driver "mouse"
#Option "CorePointer"
# The mouse protocol and device. The device is normally set to /dev/mouse,
# which is usually a symbolic link to the real device.
#Option "Protocol" "Microsoft"
Option "Device" "/dev/ps2mouse"
# On platforms where PnP mouse detection is supported the following
# protocol setting can be used when using a newer PnP mouse:
# Option "Protocol" "Auto"
# When using mouse connected to a PS/2 port (aka "MousePort"), set the
# the protocol as follows. On some platforms some other settings may
# be available.
Option "Protocol" "PS/2"
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris), use
# the following instead of any of the lines above. The Device line
# is not required in this case.
# Option "Protocol" "Xqueue"
# Emulate3Buttons is an option for 2-button mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)
Option "Emulate3Buttons" "true"
# Option "Emulate3Timeout" "50"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
Identifier "Mouse USB"
Driver "mouse"
Option "Protocol" "auto"
# device is usually a symbolic link to the real device
Option "Device" "/dev/usbmouse"
EndSection
Section "InputDevice"
Identifier "Synaptics Touchpad"
Driver "synaptics"
# device is usually a symbolic link to the real device
Option "Device" "/dev/touchpad"
Option "Protocol" "auto-dev"
#Option "SendCoreEvents" "true"
#Option "ZAxisMapping" "Y"
#Option "Emulate3Buttons" "true"
#Option "Emulate3Timeout" "100"
# Next line required only if you want to disable the mousepad while typing:
#Option "SHMConfig" "on"
# Tweak this option as you like, it works anyway, have a look in
# /usr/share/doc/synaptics*/README.gz for more options
Option "LeftEdge" "120"
Option "RightEdge" "830"
Option "TopEdge" "120"
Option "BottomEdge" "650"
Option "FingerLow" "14"
Option "FingerHigh" "15"
Option "MaxTapTime" "180"
Option "MaxTapMove" "110"
Option "EmulateMidButtonTime" "75"
Option "VertScrollDelta" "20"
Option "HorizScrollDelta" "20"
Option "MinSpeed" "0.30"
Option "MaxSpeed" "0.75"
Option "AccelFactor" "0.015"
Option "EdgeMotionSpeed" "200"
Option "EdgeMotionMinSpeed" "200"
Option "EdgeMotionMaxSpeed" "200"
Option "CircularScrolling" "1"
Option "CircScrollDelta" "0.1"
Option "CircScrollTrigger" "2"
Option "UpDownScrolling" "1"
#Option "TouchpadOff" "0"
#Option "Repeater" "/dev/ps2mouse"
EndSection
# Some examples of extended input devices
# Section "InputDevice"
# Identifier "spaceball"
# Driver "magellan"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "spaceball2"
# Driver "spaceorb"
# Option "Device" "/dev/cua0"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen0"
# Driver "microtouch"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "1412"
# Option "MaxX" "15184"
# Option "MinY" "15372"
# Option "MaxY" "1230"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
# Identifier "touchscreen1"
# Driver "elo2300"
# Option "Device" "/dev/ttyS0"
# Option "MinX" "231"
# Option "MaxX" "3868"
# Option "MinY" "3858"
# Option "MaxY" "272"
# Option "ScreenNumber" "0"
# Option "ReportingMode" "Scaled"
# Option "ButtonThreshold" "17"
# Option "ButtonNumber" "1"
# Option "SendCoreEvents"
# EndSection
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "Monitor 1 LCD"
Option "DPMS"
Modeline "1280x800@60" 83.91 1280 1312 1624 1656 800 816 824 841
EndSection
Section "Monitor"
# The identifier line must be present.
Identifier "Monitor 2 Genérico"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
HorizSync 31.5 # typical for a single frequency fixed-sync monitor
# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
VertRefresh 60 # typical for a single frequency fixed-sync monitor
# VertRefresh 50-100 # multisync
# VertRefresh 60, 65 # multiple fixed sync frequencies
# VertRefresh 40-50, 80-100 # multiple ranges of sync frequencies
# Modes can be specified in two formats. A compact one-line format, or
# a multi-line format.
# A generic VGA 640x480 mode (hsync = 31.5kHz, refresh = 60Hz)
# These two are equivalent
# ModeLine "640x480" 25.175 640 664 760 800 480 491 493 525
# Mode "640x480"
# DotClock 25.175
# HTimings 640 664 760 800
# VTimings 480 491 493 525
# EndMode
# These two are equivalent
# ModeLine "1024x768i" 45 1024 1048 1208 1264 768 776 784 817 Interlace
Mode "1024x768i"
DotClock 45
HTimings 1024 1048 1208 1264
VTimings 768 776 784 817
Flags "Interlace"
EndMode
# If a monitor has DPMS support, that can be indicated here. This will
# enable DPMS when the monitor is used with drivers that support it.
# Option "dpms"
# If a monitor requires that the sync signals be superimposed on the
# green signal, the following option will enable this when used with
# drivers that support it. Only a relatively small range of hardware
# (and drivers) actually support this.
# Option "sync on green"
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
# Any number of graphics device sections may be present
Section "Device"
# The Identifier must be present.
Identifier "Generic VGA"
# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.
Driver "vga"
# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.
# Chipset "generic"
# Various other lines can be specified to override the driver's automatic
# detection code. In most cases they are not needed.
# VideoRam 256
# Clocks 25.2 28.3
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.
# BusID "PCI:0:10:0"
# Various option lines can be added here as required. Some options
# are more appropriate in Screen sections, Display subsections or even
# Monitor sections.
# Option "hw cursor" "off"
EndSection
Section "Device"
Identifier "ATI Technologies, Inc. Radeon IGP 340M"
Driver "ati"
BusID "PCI:1:5:0"
EndSection
# **********************************************************************
# Screen sections.
# **********************************************************************
# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
# The Identifier, Device and Monitor lines must be present
Identifier "Ordinary Screen"
Device "Generic VGA"
Monitor "Monitor 1 LCD"
# The favoured Depth and/or Bpp may be specified here
DefaultDepth 16
SubSection "Display"
Depth 16
Modes "1024x768"
EndSubSection
EndSection
Section "Screen"
Identifier "Auxiliary Screen"
#Device "ATI Technologies, Inc. Radeon IGP 340M"
Device "Generic VGA"
#Monitor "Monitor 1 LCD"
Monitor "Monitor 2 Genérico"
Option "no accel"
DefaultDepth 16
# DefaultDepth 24
SubSection "Display"
Depth 16
Modes "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Section "Screen"
Identifier "Default Screen"
Device "ATI Technologies, Inc. Radeon IGP 340M"
Monitor "Monitor 1 LCD"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1280x800"
EndSubSection
EndSection
# **********************************************************************
# ServerLayout sections.
# **********************************************************************
# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.
Section "ServerLayout"
# The Identifier line must be present
Identifier "Main Layout"
# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.
Screen "Default Screen"
#Screen "Screen MGA 1" "" "" "" "Screen MGA 2"
#Screen "Screen MGA 2" "" "" "Screen MGA 1" ""
# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents". In this example, "Mouse1" is the core pointer,
# and "Mouse2" is an extended input device that also generates core
# pointer events (i.e., both mice will move the standard pointer).
#InputDevice "PS/2 Mouse" "CorePointer"
#InputDevice "PS/2 Mouse" "AlwaysCore"
#InputDevice "Synaptics Touchpad" "SendCoreEvents"
#InputDevice "Synaptics Touchpad" "AlwaysCore"
InputDevice "Synaptics Touchpad" "Corepointer"
#InputDevice "Mouse USB"
InputDevice "AT Translated Set 2 keyboard" "CoreKeyboard"
EndSection
Section "ServerLayout"
Identifier "another layout"
Screen "Default Screen" LeftOf "Ordinary Screen"
InputDevice "PS/2 Mouse" "CorePointer"
InputDevice "AT Translated Set 2 keyboard" "CoreKeyboard"
EndSection
Section "ServerLayout"
Identifier "simple layout"
Screen "Ordinary Screen"
InputDevice "PS/2 Mouse" "CorePointer"
InputDevice "AT Translated Set 2 keyboard" "CoreKeyboard"
EndSection
Section "DRI"
Mode 0666
EndSection
|
Look and try specialy this part
| Code: |
Section "Files"
RgbPath "/usr/lib/X11/rgb"
FontPath "/usr/share/fonts/local/"
FontPath "/usr/share/fonts/misc/"
FontPath "/usr/share/fonts/75dpi/:unscaled"
FontPath "/usr/share/fonts/100dpi/:unscaled"
FontPath "/usr/share/fonts/Type1/"
FontPath "/usr/share/fonts/TTF/"
FontPath "/usr/share/fonts/CID/"
FontPath "/usr/share/fonts/75dpi/"
FontPath "/usr/share/fonts/100dpi/"
EndSection
Section "Module"
Load "dbe"
SubSection "extmod"
Option "omit xfree86-dga"
EndSubSection
Load "type1"
Load "freetype"
EndSection
Section "InputDevice"
Identifier "AT Translated Set 2 keyboard"
Driver "keyboard"
Option "XkbModel" "pc105"
Option "XkbLayout" "br"
Option "XkbVariant" "us_intl"
Option "XkbOptions" ""
EndSection
Section "InputDevice"
Identifier "PS/2 Mouse"
Driver "mouse"
Option "Device" "/dev/psaux"
Option "Protocol" "PS/2"
Option "Emulate3Buttons" "true"
Option "ZAxisMapping" "4 5"
EndSection
Section "Monitor"
Identifier "Monitor 1 LCD"
Option "DPMS"
Modeline "1280x800@60" 83.91 1280 1312 1624 1656 800 816 824 841
EndSection
Section "Device"
Identifier "ATI Technologies, Inc. Radeon IGP 340M"
Driver "ati"
EndSection
Section "Screen"
Identifier "Default Screen"
Device "ATI Technologies, Inc. Radeon IGP 340M"
Monitor "Monitor 1 LCD"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1280x800"
EndSubSection
EndSection
Section "ServerLayout"
Identifier "Main Layout"
Screen "Default Screen"
InputDevice "PS/2 Mouse" "CorePointer"
InputDevice "AT Translated Set 2 keyboard" "CoreKeyboard"
EndSection
|
|
|
| Back to top |
|
|
candrews
Developer
Joined: 10 Aug 2005
Posts: 162
|
| Posted: Fri Mar 03, 2006 10:51 pm Post subject: |
|
|
| I likewise get this kernel panic. I thought it was just me - I'm glad to see I'm not alone! |
|
| Back to top |
|
|
pmouse
n00b
Joined: 07 Dec 2005
Posts: 20
|
| Posted: Sat Mar 11, 2006 6:42 am Post subject: |
|
|
the "fglrx" is because of the ati-drivers, and is not the cause of the problem.
I too experiences this, on my T42/Raedon 9600. It's defintely a bug and should be reported...
On a side note, I think this also causes the CRT out to break. I can't get any projector output under X, only under console.
Regards,
Peter |
|
| Back to top |
|
|
Admiral_Trigger_Happy
Guru
Joined: 05 Sep 2004
Posts: 337
Location: Australia
|
| Posted: Sat Mar 11, 2006 3:06 pm Post subject: |
|
|
Are you guys using the 2.6.15 kernel?
It won't work with most ATI drivers atm
_________________
Admiral Trigger Happy
-------------------------------
www.kiba-dock.org |
|
| Back to top |
|
|
hiroki
Guru
Joined: 29 Jul 2003
Posts: 327
Location: @home in germany
|
| Posted: Sat Mar 11, 2006 4:08 pm Post subject: |
|
|
| Admiral_Trigger_Happy wrote: | Are you guys using the 2.6.15 kernel?
It won't work with most ATI drivers atm |
oic, well, that would explain it 
i am using gentoo-sources-2.6.15-r7 now. r5 before.
well then...  |
|
| Back to top |
|
|
Admiral_Trigger_Happy
Guru
Joined: 05 Sep 2004
Posts: 337
Location: Australia
|
| Posted: Sat Mar 11, 2006 5:32 pm Post subject: |
|
|
I tried to upgrade to the 2.6.15, but downgraded due to the ati driver not working nicely
There is a new ati driver, hopefully it won't be long to its in portage
_________________
Admiral Trigger Happy
-------------------------------
www.kiba-dock.org |
|
| Back to top |
|
|
pmouse
n00b
Joined: 07 Dec 2005
Posts: 20
|
| Posted: Mon Mar 13, 2006 6:52 am Post subject: |
|
|
new driver is out!!
testing now |
|
| Back to top |
|
|
pmouse
n00b
Joined: 07 Dec 2005
Posts: 20
|
| Posted: Mon Mar 13, 2006 7:06 am Post subject: |
|
|
| pmouse wrote: | new driver is out!!
testing now |
can't get it emerged tho
needs glibc 2.4, which needs nptl-only, which breaks matlab |
|
| Back to top |
|
|
ranyus
n00b
Joined: 12 Feb 2004
Posts: 13
Location: Milano, Italy
|
| Posted: Mon Mar 13, 2006 9:15 am Post subject: |
|
|
| candrews wrote: | | I likewise get this kernel panic. I thought it was just me - I'm glad to see I'm not alone! |
I've the same problem (using fglrx driver), and I've noticed that if I comment "Load glx" in my xorg.conf, all works well apart the 3D acceleration...Are there ideas?? 
_________________
--[]--Ranyus--[]-- |
|
| Back to top |
|
|
seiichiro0185
Tux's lil' helper
Joined: 18 Dec 2005
Posts: 115
Location: Berlin, Germany
|
| Posted: Mon Mar 13, 2006 8:12 pm Post subject: |
|
|
same problem here. When using ati-drivers >8.21.7-r1 I get a Kernel-panic when shuting down the system, during stopping gdm (hard freeze, only turning off with the powerbutton works). Same thing happens if I unload the fglrx-module with rmmod. I'm using gentoo-sources-2.6.15-r1, my card is a mobility radeon M10 (9700 Mobility). The new 8.23.7 driver didn't help, still freezing.
seiichiro0185
_________________
Desktop: AMD Athlon64 4850e@2,9GHz| 2GB RAM | 500GB HDD
Laptop: Dell Vostro 1310: C2D 2.1GHz | 4GB RAM | 250GB HDD
Server: Via C7D 1,5GHz | 512MB RAM | 1TB HDD |
|
| Back to top |
|
|
pmouse
n00b
Joined: 07 Dec 2005
Posts: 20
|
| Posted: Tue Mar 14, 2006 7:48 am Post subject: |
|
|
it's a kernel problem, newer driver/glibc 2.4 does not fix this.
--- as of March 14, 06' |
|
| Back to top |
|
|
prior_philip
n00b
Joined: 18 Feb 2004
Posts: 57
Location: Geißbockheim
|
| Posted: Tue Mar 14, 2006 7:30 pm Post subject: |
|
|
Same here. Notebook hangs up when sending it to suspend or hibernate. I'll change the graphics chip to nvidia 
_________________
Wat kann denn isch dafür dat der nix dafür kann?! Nää-nää, da kann isch nix dafür. |
|
| Back to top |
|
|
chrb
n00b
Joined: 23 Jun 2002
Posts: 19
|
| Posted: Sun Mar 19, 2006 3:02 pm Post subject: |
|
|
| Make sure you have the correct AGP driver for your motherboard (eg. intel-agp), and try setting UseFastTLS to 2 in xorg.conf. |
|
| Back to top |
|
|
VooDooSuN
n00b
Joined: 17 Apr 2005
Posts: 20
Location: Krefeld / Ger
|
| Posted: Sun Mar 19, 2006 3:56 pm Post subject: |
|
|
Same here...
Kernel 2.6.15-r7
fglrx 8.22.5
after i changed my mouse settings to this:
| Code: |
Section "InputDevice"
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "evdev"
Option "Dev Name" "Razer Razer Copperhead Laser Mouse" # cat /proc/bus/input/devices
Option "Dev Phys" "usb-0000:00:02.0-1/input0" # cat /proc/bus/input/devices
Option "Device" "/dev/input/mouse0" # /dev/input/event0 works too
Option "Resolution" "2000"
Option "ZAxisMapping" "6 7"
Option "buttons" "7"
Option "Emulate3Buttons" "off"
|
its not possible to start up gdm, it crashs directly after the start command....
no prob to start up with "normal" mouse settings ... but then it crashs if i try to stop the gdm or wanne reboot.
UseFastTLS = "2" also dont solve the prob... ^^ |
|
| Back to top |
|
|
VooDooSuN
n00b
Joined: 17 Apr 2005
Posts: 20
Location: Krefeld / Ger
|
| Posted: Sun Mar 19, 2006 4:52 pm Post subject: |
|
|
okay ... found my start up problem ...
there was a typO in in mouse device setting ...
so gdm starts up again... but the crashes after shutting down gdm, it still there...
i also tested out the "new" ATI 8.23.7 driver... no changes...
 |
|
| Back to top |
|
|
xavan
n00b
Joined: 20 Jun 2003
Posts: 50
|
| Posted: Fri Apr 07, 2006 9:08 am Post subject: |
|
|
| Does someone test the sys-kernel/gentoo-sources-2.6.16-r1? |
|
| Back to top |
|
|
VooDooSuN
n00b
Joined: 17 Apr 2005
Posts: 20
Location: Krefeld / Ger
|
| Posted: Fri Apr 07, 2006 12:38 pm Post subject: |
|
|
Nope ... sorry m8
havent testet it till yet...
i think.... i will wait... till the first 2.6.16-x stable version is out.
 |
|
| Back to top |
|
|
seiichiro0185
Tux's lil' helper
Joined: 18 Dec 2005
Posts: 115
Location: Berlin, Germany
|
| Posted: Fri Apr 07, 2006 6:37 pm Post subject: |
|
|
I'm using gentoo-sources-2.6.16-r1, no change, still the same behavior 
seiichiro0185
_________________
Desktop: AMD Athlon64 4850e@2,9GHz| 2GB RAM | 500GB HDD
Laptop: Dell Vostro 1310: C2D 2.1GHz | 4GB RAM | 250GB HDD
Server: Via C7D 1,5GHz | 512MB RAM | 1TB HDD |
|
| Back to top |
|
|
annunaki2k2
Tux's lil' helper
Joined: 14 Oct 2003
Posts: 119
Location: Streatham, London, UK
|
| Posted: Sat Apr 08, 2006 2:18 pm Post subject: |
|
|
Thought I'd just add my 2 cents as well.
I'm having the exact same problem - kernel panic after unloading X then trying to reload it.
Can't be sure when it first started, but it must be very recent...
Could it be gcc 4/glibc2.4 related?
| Code: | kryten ~ # emerge --info
Portage 2.1_pre7-r4 (default-linux/x86/2006.0, gcc-4.0.3, glibc-2.4-r1, 2.6.16-gentoo-r1 i686)
=================================================================
System uname: 2.6.16-gentoo-r1 i686 AMD Athlon(tm) XP 3200+
Gentoo Base System version 1.12.0_pre17
ccache version 2.4 [enabled]
dev-lang/python: 2.3.5, 2.4.2-r1
sys-apps/sandbox: 1.2.17
sys-devel/autoconf: 2.13, 2.59-r7
sys-devel/automake: 1.4_p6, 1.5, 1.6.3, 1.7.9-r1, 1.8.5-r3, 1.9.6-r2
sys-devel/binutils: 2.16.91.0.6
sys-devel/libtool: 1.5.22
virtual/os-headers: 2.6.11-r3
ACCEPT_KEYWORDS="x86 ~x86"
AUTOCLEAN="yes"
CBUILD="i686-pc-linux-gnu"
CFLAGS="-march=athlon-xp -O2 -mfpmath=sse,387 -fforce-addr -fno-align-labels -falign-functions=16 -falign-loops=4 -falign-jumps=4 -maccumulate-outgoing-args -fprefetch-loop-arrays -fomit-frame-pointer -pipe"
CHOST="i686-pc-linux-gnu"
CONFIG_PROTECT="/etc /usr/kde/2/share/config /usr/kde/3/share/config /usr/lib/mozilla/defaults/pref /usr/share/X11/xkb /usr/share/config /var/qmail/control"
CONFIG_PROTECT_MASK="/etc/eselect/compiler /etc/gconf /etc/terminfo /etc/env.d"CXXFLAGS="-march=athlon-xp -O2 -mfpmath=sse,387 -fforce-addr -fno-align-labels -falign-functions=16 -falign-loops=4 -falign-jumps=4 -maccumulate-outgoing-args -fprefetch-loop-arrays -fomit-frame-pointer -pipe"
DISTDIR="/usr/portage/distfiles"
FEATURES="autoconfig ccache confcache distlocks metadata-transfer prelink sandbox sfperms strict"
GENTOO_MIRRORS="http://gentoo.blueyonder.co.uk http://www.mirrorservice.org/sites/www.ibiblio.org/gentoo/ http://mirrors.sec.informatik.tu-darmstadt.de/gentoo/ http://ftp.uni-erlangen.de/pub/mirrors/gentoo http://ftp.heanet.ie/pub/gentoo/ http://ftp.snt.utwente.nl/pub/os/linux/gentoo"
LANG="en_GB"
LDFLAGS="-Wl,-O1"
LINGUAS="en_GB"
MAKEOPTS="-j2"
PKGDIR="/usr/portage/packages"
PORTAGE_TMPDIR="/var/tmp"
PORTDIR="/usr/portage"
PORTDIR_OVERLAY="/usr/local/portage /usr/local/overlays/gnome-experimental"
SYNC="rsync://rsync.gentoo.org/gentoo-portage"
USE="/ 3dnow 3dnowext 7zip X a52 aac aalib acpi aim alsa apache2 audiofile avi bidi bitmap bitmap-fonts bluetooth bonobo bzip2 cairo caps cdda cddb cdio cdparanoia cdr cjk cli crypt ctype cups curl dba dbus dga dhcp divx4linux dpms dri dv dvb dvd dvdr dvdread eds emboss encode esd evo evolution exif expat faad fastbuild fastcgi fbcon ffmpeg fglrx firefox flac flash foomaticdb force-cgi-redirect fortran ftp fuse gb gd gdbm gif gimp glibc-omitfp gnome gphoto2 gpm gstreamer gtk gtk2 gtkhtml hal icq ieee1394 imagemagick imlib ipv6 isdnlog jabber jack java javascript jikes joystick jpeg kerberos krb4 lcms ldap libg++ libvisual libwww linguas_en_GB lirc live lm_sensors mad matroska memlimit migemo mikmod mime ming mjpeg mmx mmx2 mmxext mng modplug mozilla moznocompose moznoirc moznomail mozsvg mp3 mp4 mpeg mpi mppe-mppc msn musepack nas nautilus ncurses network nforce2 nfs nls nptl nptlonly nsplugin oav odbc offensive ogg oggvorbis on-the-fly-crypt opengl oscar pam pcre pda pdflib perl pic pmu png posix ppds pppd prelude python qt quicktime radeon readline real rtc samba sasl scanner sdl session shorten simplexml slp sndfile snmp soap sockets sox speex spell spl sse ssl stream sysfs syslog szip tcltk tcpd theora tiff tokenizer truetype truetype-fonts type1-fonts udev unicode usb userlocales v4l v4l2 vcd videos vidix vorbis win32codecs wma wmf x264 x86 xinerama xml xml2 xmms xorg xosd xpm xprint xsl xv xvid yahoo zlib elibc_glibc input_devices_keyboard input_devices_mouse input_devices_joystick input_devices_evdev kernel_linux userland_GNU video_cards_fglrx video_cards_ati video_cards_vesa"
Unset: ASFLAGS, CTARGET, EMERGE_DEFAULT_OPTS, INSTALL_MASK, LC_ALLe issue. here is my set-up:
|
_________________
The great thing about standards is there are so many to choose from..... |
|
| Back to top |
|
|
seiichiro0185
Tux's lil' helper
Joined: 18 Dec 2005
Posts: 115
Location: Berlin, Germany
|
| Posted: Sat Apr 08, 2006 5:23 pm Post subject: |
|
|
| Quote: | | Could it be gcc 4/glibc2.4 related? |
not really, I'm using stable gcc-3.4.4 and glibc-2.3.5-r2...
seiichiro0185
_________________
Desktop: AMD Athlon64 4850e@2,9GHz| 2GB RAM | 500GB HDD
Laptop: Dell Vostro 1310: C2D 2.1GHz | 4GB RAM | 250GB HDD
Server: Via C7D 1,5GHz | 512MB RAM | 1TB HDD |
|
| Back to top |
|
|
Jkay
Apprentice
Joined: 31 Dec 2002
Posts: 214
Location: thatched-roof cottages
|
| Posted: Sun Apr 09, 2006 1:41 am Post subject: |
|
|
I love forum search!
I am having the exact same problem, with the same errors in the log file. GDM crashes on re-start .. INITIAL system start is fine tho. This means I can never log out
LUCKILY I can log in using openssh from the windows box (putty) in the other room here in order to do a clean shut-down/reboot with the reboot command.
| Code: | kernel 2.6.15-gentoo-r1
OpenGL vendor string: ATI Technologies Inc.
OpenGL renderer string: RADEON 9800 XT Generic
OpenGL version string: 2.0.5582 (8.21.7)
|
|
|
| Back to top |
|
|
annunaki2k2
Tux's lil' helper
Joined: 14 Oct 2003
Posts: 119
Location: Streatham, London, UK
|
| Posted: Sun Apr 09, 2006 9:14 am Post subject: |
|
|
| seiichiro0185 wrote: | | not really, I'm using stable gcc-3.4.4 and glibc-2.3.5-r2... |
You sunk my battle ship!
Could it be model specific? I have a 9800 XT in my work horse, but my laptop (which doesn't seem to experience the problem) has a mobile 9800.
_________________
The great thing about standards is there are so many to choose from..... |
|
| Back to top |
|
|
seiichiro0185
Tux's lil' helper
Joined: 18 Dec 2005
Posts: 115
Location: Berlin, Germany
|
| Posted: Sun Apr 09, 2006 10:47 am Post subject: |
|
|
| annunaki2k2 wrote: |
Could it be model specific? I have a 9800 XT in my work horse, but my laptop (which doesn't seem to experience the problem) has a mobile 9800. |
I'm experiencing this on a laptop with an Radeon 9700 Mobility (as I wrote before), and the hiroki and pmouse seem to have a Mobility 9600. So at least it isn't one specific model, but it seems (from all who have postet which cards they use) that it affects the 9x00 series.
What I noticed when I read through the thread once more is: it seems that everyone is using gentoo-sources. Maybe its related to one of the gentoo-patches? I'll go and give vanilla-sources a try (altough this means that some other things may stop working)...
[EDIT]
Just installed vanilla-sources-2.6.15.1 and ati-drivers-8.23.7 and it shows the same behavior as before. I still get the kernel bug when stoping xdm . So gentoo-patches aren't the problem.
[/EDIT]
seiichiro0185
_________________
Desktop: AMD Athlon64 4850e@2,9GHz| 2GB RAM | 500GB HDD
Laptop: Dell Vostro 1310: C2D 2.1GHz | 4GB RAM | 250GB HDD
Server: Via C7D 1,5GHz | 512MB RAM | 1TB HDD |
|
| Back to top |
|
|
Jkay
Apprentice
Joined: 31 Dec 2002
Posts: 214
Location: thatched-roof cottages
|
| Posted: Sun Apr 09, 2006 4:41 pm Post subject: |
|
|
So ... gdm starts perfectly, but any further gdm stop/start causes it to seize up. The kernel itself is still running, but any local user is now blocked from shell/GUI access. Remote SSH connections work perfectly tho so the system, as a whole, is intact and operating.
The $100 question is "what is different about subsequent gdm operations with regard to the initial one?"
If it works the first time, why does it completely freeze on any further executions?? |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
