RoundsToZero Guru
Joined: 17 Nov 2003 Posts: 478 Location: New York, NY
|
Posted: Tue Mar 28, 2006 9:34 pm Post subject: question about lm_sensors alarm with Asus P4S800D-X |
|
|
After some tweaking of sensors.conf, I am left with the following alarms:
Code: |
VCore: +1.56 V (min = +1.94 V, max = +1.94 V) ALARM
-12V: +6.06 V (min = -13.18 V, max = -10.80 V) ALARM
VBat: +0.00 V (min = +2.40 V, max = +3.60 V) ALARM
|
I figure the third one is okay because I know there is a battery in there and the motherboard has no problems retaining its settings as far as I know. But what about the first two? Here's the section of my sensors.conf:
Code: |
chip "w83627thf-*" "w83637hf-*"
# Rather than an internal inverting op amp, the 627thf uses standard positive
# inputs and the negative voltages are level shifted by a 3.6V reference
# (same as 82d/83s).
# The math is convoluted, so we hope that your motherboard
# uses the recommended resistor values.
# Note that in1 (+12V) is the usual in4, and in4 (-12V) is the usual in5.
# Data sheet is obviously wrong for in4, the usual formula should work.
# No in5 nor in6.
# sensors doesn't need the ignore lines but sensord does...
ignore in5
ignore in6
label in0 "VCore"
label in1 "+12V"
label in2 "+3.3V"
label in3 "+5V"
label in4 "-12V"
label in7 "V5SB"
label in8 "VBat"
# Mori Hiroyuki reported to need this (P4P800)
# compute in0 @/2, @*2
compute in1 ((28/10)+1)*@, @/((28/10)+1)
compute in3 ((34/51)+1)*@, @/((34/51)+1)
compute in4 (5.14*@)-14.91, (@+14.91)/5.14
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
# adjust this if your vid is wrong; see doc/vid
set vrm 9.0
# set limits to 5% for the critical voltages
# set limits to 10% for the non-critical voltages
# set limits to 20% for the battery voltage
# if your vid is wrong, you'll need to adjust in0_min and in0_max
set in0_min vid * 0.95
set in0_max vid * 1.05
set in1_min 12 * 0.90
set in1_max 12 * 1.10
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min -12 * 1.10
set in4_max -12 * 0.90
set in7_min 5 * 0.95
set in7_max 5 * 1.05
set in8_min 3.0 * 0.80
set in8_max 3.0 * 1.20
# set up sensor types (thermistor is default)
# 1 = PII/Celeron Diode; 2 = 3904 transistor;
# 3435 = thermistor with Beta = 3435
# If temperature changes very little, try 1 or 2.
# set sensor1 1
# set sensor2 2
# set sensor3 3435
label temp1 "M/B Temp"
label temp2 "CPU Temp"
# ignore temp3
# examples for temperature limits
set temp1_over 40
set temp1_hyst 37
# set temp2_over 52
# set temp2_hyst 47
# set temp3_over 52
# set temp3_hyst 47
ignore fan1
label fan2 "CPU Fan"
set fan2_min 2000
ignore fan3
|
|
|