| View previous topic :: View next topic |
| Author |
Message |
blukske
n00b
Joined: 22 Jul 2005
Posts: 8
|
 Posted: Wed Nov 30, 2005 6:50 am Post subject: Problem detecting gp2x SD card over USB2.0 [Solved] |
 |
|
Hi all,
I recently bought myself a gp2x handheld (http://www.gp2x.com). I'm having problems getting Gentoo to recognize the SD card when connecting it to my PC using USB2.0. I'm using the latest gentoo-sources, kernel 2.6.14-r3 together with udev. As far as I know I've set all the required USB settings in my kernel config. I've got no problems with my other USB stuff, a memory stick, mouse, and gamepad. I recently tried to detect the SD card using Knoppix and an old 2.4 kernel, and it just worked! 
These are the relevant USB messages from dmesg during startup:
| Code: |
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 21 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:10.3, from 0 to 2
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: reset hcs_params 0x3206 dbg=0 cc=3 pcc=2 ordered !ppc por ts=6
ehci_hcd 0000:00:10.3: reset hcc_params 6872 thresh 7 uframes 256/512/1024
ehci_hcd 0000:00:10.3: capability 0001 at 68
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: irq 18, io mem 0xbe800000
ehci_hcd 0000:00:10.3: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:10.3: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:10.3: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
ehci_hcd 0000:00:10.3: supports USB remote wakeup
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.14-gentoo-r3 ehci_hcd
usb usb1: SerialNumber: 0000:00:10.3
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 18
hub 1-0:1.0: state 5 ports 6 chg 0000 evt 0000
ehci_hcd 0000:00:10.3: GetStatus port 2 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
PCI: Via IRQ fixup for 0000:00:10.0, from 0 to 2
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: detected 2 ports
uhci_hcd 0000:00:10.0: check_and_reset_hc: legsup = 0x003a
uhci_hcd 0000:00:10.0: Performing full reset
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 18, io base 0x0000b800
uhci_hcd 0000:00:10.0: supports USB remote wakeup
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.14-gentoo-r3 uhci_hcd
usb usb2: SerialNumber: 0000:00:10.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:10.3: port 2 low speed --> companion
ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 21 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:10.1, from 0 to 2
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: detected 2 ports
uhci_hcd 0000:00:10.1: check_and_reset_hc: legsup = 0x0010
uhci_hcd 0000:00:10.1: Performing full reset
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:10.3: GetStatus port 2 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.0: port 1 portsc 008a,00
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
uhci_hcd 0000:00:10.1: irq 18, io base 0x0000b400
uhci_hcd 0000:00:10.1: supports USB remote wakeup
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.14-gentoo-r3 uhci_hcd
usb usb3: SerialNumber: 0000:00:10.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.0: port 2 portsc 01ab,00
hub 2-0:1.0: port 2, status 0301, change 0003, 1.5 Mb/s
ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:10.2, from 0 to 2
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: detected 2 ports
uhci_hcd 0000:00:10.2: check_and_reset_hc: legsup = 0x0010
uhci_hcd 0000:00:10.2: Performing full reset
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 18, io base 0x0000b000
uhci_hcd 0000:00:10.2: supports USB remote wakeup
usb usb4: default language 0x0409
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.14-gentoo-r3 uhci_hcd
usb usb4: SerialNumber: 0000:00:10.2
usb usb4: hotplug
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
Initializing USB Mass Storage driver...
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: skipped 1 descriptor after interface
usb 2-2: default language 0x0409
usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-2: Product: USB Receiver
usb 2-2: Manufacturer: Logitech
usb 2-2: hotplug
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
usb 2-2:1.0: hotplug
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.1: port 1 portsc 008a,00
hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.1: port 2 portsc 008a,00
hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 4-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:00:10.2: port 1 portsc 008a,00
hub 4-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
usbcore: registered new driver hiddev
hub 4-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:00:10.2: port 2 portsc 008a,00
hub 4-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0000
usbhid 2-2:1.0: usb_probe_interface
usbhid 2-2:1.0: usb_probe_interface - got id
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:10.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
|
And this is what tail -f /var/log/everything/current gives me when plugging in the device:
| Code: |
Nov 30 12:26:41 [kernel] usb 1-1: new high speed USB device using ehci_hcd and address 3
Nov 30 12:26:42 [kernel] usb 1-1: Product: File-backed Storage Gadget
Nov 30 12:26:42 [kernel] usb 1-1: Manufacturer: Linux 2.4.25 with net2272
Nov 30 12:26:42 [kernel] usb 1-1: SerialNumber: 3035204A756E
Nov 30 12:26:46 [kernel] usb 1-1: can't set config #1, error -110
Nov 30 12:26:47 [kernel] usb 1-1: new high speed USB device using ehci_hcd and address 4
Nov 30 12:26:47 [kernel] usb 1-1: Product: File-backed Storage Gadget
Nov 30 12:26:47 [kernel] usb 1-1: Manufacturer: Linux 2.4.25 with net2272
Nov 30 12:26:47 [kernel] usb 1-1: SerialNumber: 3035204A756E
Nov 30 12:26:52 [kernel] usb 1-1: can't set config #1, error -110
Nov 30 12:26:52 [kernel] usb 1-1: new high speed USB device using ehci_hcd and address 5
Nov 30 12:26:52 [kernel] usb 1-1: Product: File-backed Storage Gadget
Nov 30 12:26:52 [kernel] usb 1-1: Manufacturer: Linux 2.4.25 with net2272
Nov 30 12:26:52 [kernel] usb 1-1: SerialNumber: 3035204A756E
Nov 30 12:26:55 [kernel] usb 1-1: can't set config #1, error -110
|
Anyone got an idea on how to fix this?
Last edited by blukske on Wed Nov 30, 2005 12:17 pm; edited 1 time in total |
|
| Back to top |
|
 |
blukske
n00b
Joined: 22 Jul 2005
Posts: 8
|
| Posted: Wed Nov 30, 2005 12:16 pm Post subject: |
|
|
Solved, kind of. As it turns out, the gp2x does not yet support usb2.0 properly. Now I just don't load the ehci-hcd module to force the device to use USB1.1. Works like a charm, although somewhat slow  |
|
| Back to top |
|
|
Solution_9
Guru
Joined: 22 Jun 2003
Posts: 311
|
| Posted: Thu Dec 01, 2005 12:37 am Post subject: |
|
|
Props to the GP2X. Mine is coming as we speek (or rather as i type this)
_________________
"The X server has to be the biggest program I've ever seen that doesn't do anything for you."
- Ken Thompson |
|
| Back to top |
|
|
borkdox
Tux's lil' helper
Joined: 16 Jan 2004
Posts: 123
|
| Posted: Fri Dec 02, 2005 4:09 pm Post subject: |
|
|
i have a gp2x too, this is great, lot of gentooers with gp2x  |
|
| Back to top |
|
|
telengard
n00b
Joined: 21 Jan 2004
Posts: 12
Location: New Hampshire
|
| Posted: Thu Dec 29, 2005 9:24 pm Post subject: |
|
|
| borkdox wrote: | | i have a gp2x too, this is great, lot of gentooers with gp2x |
Yep, I got one too for xmas. Lovin' the Atari 800 emulator.
Anyone here got a cross compiling env setup yet under Gentoo? I want to try porting an emulator.
~telengard |
|
| Back to top |
|
|
LukeLemmings
n00b
Joined: 25 Feb 2004
Posts: 25
|
| Posted: Wed Apr 04, 2007 2:30 pm Post subject: |
|
|
And another one!
L.
_________________
Always suspect an attempt at humor. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Kernel & Hardware
