View previous topic :: View next topic |
Author |
Message |
calinb n00b
Joined: 31 Aug 2006 Posts: 10
|
Posted: Wed Aug 01, 2007 7:17 pm Post subject: |
|
|
wynn wrote: | reddeath: there are (IMHO) three reasons for "network interface eth0 does not exist".
...<snip> ...
the third to do with /etc/udev/rules.d/70-persistent-net.rules doesn't seem likely. |
I had this problem when I replaced a PCI card NIC. My network would not start. I tried many other cards and also my mobo NIC to no avail. It turns out that every time I installed a new NIC, /etc/udev/rules.d/70-persistent-net.rules would get updated with an additional entry and the ethX label would get incremented. The net.ethX symlinks in /etc/init.d must match the entries in the /etc/udev/rules.d/ files but the symlinks do not get updated automatically. After many kernel builds and much mod-probing around, I found this thread:
https://forums.gentoo.org/viewtopic-t-569240-highlight-device+exist.html
Hope this saves some time for others reading this sticky thread. _________________ -Cal |
|
Back to top |
|
|
toto89 n00b
Joined: 08 Aug 2006 Posts: 37
|
Posted: Thu Sep 13, 2007 10:03 pm Post subject: |
|
|
Hi,
I just install my gentoo and I got a Code: | ERROR: Problem starting needed services
"Netmount" was not started | or something like that, eth0 is not found.
I follow the handbook for the installation and I add the SysKonnect Yukon2 support and/or (try both) the New SysKonnect GigaEthernet support on the compilation of the kernel.
I got a GA-965P-DS3 and a router linksys wrt54gs. My router is set on PPPoE, I try this: http://gentoo-wiki.com/HOWTO_Connect_using_PPPoE but I got the same message.
My ipconfig -a:
Code: | lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1152 errors:0 dropped:0 overruns:0 frame:0
TX packets:1152 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:57600 (56.2 KiB) TX bytes:57600 (56.2 KiB)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) |
My lsmod:
Code: |
Module Size Used by
binfmt_misc 16012 1
rfcomm 51360 0
l2cap 31744 5 rfcomm
bluetooth 64644 4 rfcomm,l2cap
ppdev 12296 0
lp 16584 0
acpi_cpufreq 9860 1
cpufreq_userspace 6560 0
cpufreq_stats 9312 0
freq_table 7104 2 acpi_cpufreq,cpufreq_stats
cpufreq_powersave 3456 0
cpufreq_ondemand 10928 2
cpufreq_conservative 11272 0
video 22920 0
tc1100_wmi 10632 0
sony_acpi 7704 0
sbs 20928 0
pcc_acpi 19968 0
i2c_ec 7808 1 sbs
i2c_core 29312 1 i2c_ec
hotkey 14536 0
dev_acpi 17540 0
container 6656 0
button 9888 0
battery 14088 0
asus_acpi 21924 0
ipv6 334432 14
ac 8328 0
af_packet 29452 2
snd_hda_intel 23452 0
snd_hda_codec 219392 1 snd_hda_intel
snd_pcm_oss 57344 0
snd_mixer_oss 22784 1 snd_pcm_oss
sg 44584 0
snd_usb_audio 100512 1
snd_usb_lib 23552 1 snd_usb_audio
snd_pcm 108168 4 snd_hda_intel,snd_hda_codec,snd_pcm_oss,snd_usb_audio
snd_rawmidi 34432 1 snd_usb_lib
snd_seq_device 12180 1 snd_rawmidi
snd_hwdep 14088 1 snd_usb_audio
snd_timer 31112 1 snd_pcm
snd 79016 12 snd_hda_intel,snd_hda_codec,snd_pcm_oss,snd_mixer_oss,
snd_usb_audio,snd_pcm,snd_rawmidi,snd_seq_device,snd_hwdep,snd_timer
tsdev 11136 0
sk98lin 212572 0
soundcore 14112 1 snd
parport_pc 43560 1
hw_random 8616 0
parport 49932 3 ppdev,lp,parport_pc
intel_agp 32704 1
sky2 50436 0
pcspkr 5248 0
shpchp 49068 0
pci_hotplug 38912 1 shpchp
snd_page_alloc 13200 2 snd_hda_intel,snd_pcm
serio_raw 10244 0
floppy 76648 0
psmouse 51088 0
evdev 14592 1
squashfs 47208 1
loop 20112 2
unionfs 85152 1
nls_cp437 8704 1
isofs 43236 1
ehci_hcd 40456 0
uhci_hcd 30096 0
usbcore 167840 5 snd_usb_audio,snd_usb_lib,ehci_hcd,uhci_hcd
ide_generic 2944 0
ide_disk 21248 0
ide_cd 39584 1
cdrom 43816 1 ide_cd
jmicron 6912 0 [permanent]
ahci 24452 0
sd_mod 25728 0
generic 7428 0
ata_piix 13828 0
libata 88984 2 ahci,ata_piix
scsi_mod 181424 4 sg,ahci,sd_mod,libata
thermal 19472 0
processor 38280 2 acpi_cpufreq,thermal
fan 7432 0
vesafb 11048 0
capability 7304 0
commoncap 10752 1 capability
vga16fb 16656 1
cfbcopyarea 5376 2 vesafb,vga16fb
vgastate 10368 1 vga16fb
cfbimgblt 4352 2 vesafb,vga16fb
cfbfillrect 6272 2 vesafb,vga16fb
fbcon 45824 72
tileblit 4736 1 fbcon
font 10240 1 fbcon
bitblit 8064 1 fbcon
softcursor 3968 1 bitblit |
and my lspci
Code: |
00:00.0 Host bridge: Intel Corporation Memory Controller Hub (rev 02)
00:01.0 PCI bridge: Intel Corporation PCI Express Root Port (rev 02)
00:1a.0 USB Controller: Intel Corporation USB UHCI Controller #4 (rev 02)
00:1a.1 USB Controller: Intel Corporation USB UHCI Controller #5 (rev 02)
00:1a.7 USB Controller: Intel Corporation USB2 EHCI Controller #2 (rev 02)
00:1b.0 Audio device: Intel Corporation HD Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation PCI Express Port 1 (rev 02)
00:1c.3 PCI bridge: Intel Corporation PCI Express Port 4 (rev 02)
00:1c.4 PCI bridge: Intel Corporation PCI Express Port 5 (rev 02)
00:1d.0 USB Controller: Intel Corporation USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2)
00:1f.0 ISA bridge: Intel Corporation LPC Interface Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation SATA Controller 1 IDE (rev 02)
00:1f.3 SMBus: Intel Corporation SMBus Controller (rev 02)
00:1f.5 IDE interface: Intel Corporation SATA Controller 2 IDE (rev 02)
01:00.0 VGA compatible controller: ATI Technologies Inc Unknown device 7280
01:00.1 Display controller: ATI Technologies Inc Unknown device 72a0
03:00.0 SATA controller: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 02)
03:00.1 IDE interface: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 02)
04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 22) |
The internet work fine on the gentoo liveDVD, ubuntu liveDVD and ubuntu 6.10, 7.4, 7.10 alpha.
Split the line of lsmod output specifying what depends on the snd module, due to the usual side scrolling and layout concerns. -- desultory |
|
Back to top |
|
|
chunchengch n00b
Joined: 01 Nov 2007 Posts: 40
|
Posted: Tue Nov 06, 2007 7:24 am Post subject: |
|
|
I got the error message below while booting,
starting eth0
Bringing up eth0
dhcp
network interface eth0 does not exit
please verify hardware or kernel module (driver)
ERROR: cannot start netmount as net.eth0 could not start
I typed "ifconfig -a" to check the network interface, and I got this,
eth1 Link encap:Ethernet HWaddr.........
...............
lo Link encap:Local Loopback
...............
so, what can I do to activate eth0? thanks for any help! |
|
Back to top |
|
|
rajackson n00b
Joined: 31 Dec 2007 Posts: 30 Location: Orange County California
|
Posted: Mon Feb 25, 2008 4:32 am Post subject: simmilar problems with LiveCD 2007.0 and networking. |
|
|
I have been trying to get a machine to boot Linux with net support for weeks now. I have
been following the threads and trying various options. I am so close but am unable to see
the network. The driver I should be loading is 8139too. The following is the results of several
commands.
Code: | lspci | grep Ethernet |
results Quote: | 01:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) |
results Quote: | 8139too 22943 1
mii 7168 1 8139too |
Code: | zgrep 8139 /proc/config.gz |
results Quote: | CONFIG_8139CP=m
CONFIG_8139TOO=m
# CONFIG_8139TOO_PIO is not set
CONFIG_8139TOO_TUNE_TWISTER=y
CONFIG_8139TOO_8129=y
# CONFIG_8139_OLD_RX_RESET is not set |
Code: | zgrep MII /proc/config.gz |
results Quote: | # CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# MII PHY device drivers
CONFIG_FIXED_MII_10_FDX=y
CONFIG_FIXED_MII_100_FDX=y
CONFIG_MII=m
CONFIG_USB_USBNET_MII=m |
results Quote: | lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) |
Code: | /lib/udev/modprobe.sh -V MII |
results Quote: | * udev loading module 3.2.2
module-init-tools version 3.2.2 |
Code: | /lib/udev/modprobe.sh 8139too |
results Quote: | * udev loading module 3.2.2
module-init-tools version 3.2.2 |
Note that if I run modprobe against 8139too it hangs. The -v and -V options do not return any results. If I add
8139.too to /etc/modules.autoload.d/kernel-2.6 the boot hangs at the point which it is starting the module. If
I do not add the entry modprobe crashes as shown in the tail of the dmesg log.
Quote: | PCI: Setting latency timer of device 0000:00:1b.0 to 64
input: PC Speaker as /class/input/input2
Linux agpgart interface v0.101 (c) Dave Jones
8139too Fast Ethernet driver 0.9.28
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
BUG: unable to handle kernel NULL pointer dereference at virtual address 00000000
printing eip:
f8ed5700
*pde = 00000000
Oops: 0002 [#1]
SMP
Modules linked in: parport_pc parport 8139too mii i2c_i801 intel_agp agpgart i2c_core pcspkr snd_hda_intel snd_hda_codec snd_pcm snd_timer snd snd_page_alloc sg tg3 e1000 nfs lockd sunrpc jfs dm_mirror dm_mod pdc_adma sata_mv ata_piix ahci sata_qstor sata_vsc sata_uli sata_sis sata_sx4 sata_nv sata_via sata_svw sata_sil24 sata_sil sata_promise libata sbp2 ohci1394 ieee1394 sl811_hcd usbhid ohci_hcd uhci_hcd usb_storage ehci_hcd usbcore
CPU: 1
EIP: 0060:[<f8ed5700>] Not tainted VLI
EFLAGS: 00010202 (2.6.19-gentoo-r5 #1)
eax: 00000007 ebx: c23e9ac0 ecx: 00000001 edx: 00000000
esi: 00000000 edi: df8d1d88 ebp: df8d1d80 esp: c226ccf4
ds: 007b es: 007b ss: 0068
Process modprobe (pid: 3883, ti=c226c000 task=dfd6e560 task.ti=c226c000)
Stack: dfdf0580 f8ed6363 f8ede64a f8ede5ef 00000000 00010000 00000000 dfdd7f40
c23e9ac0 c23e9ae4 c213cc00 df8d15d8 00000004 df8d15cc df8d1580 ffffffff
00000000 f891b38f 000052d0 22222222 00010000 dfa68448 00000004 00010000
Call Trace:
[<f8ed6363>] <0> [<f891b38f>] <0> [<f8954ea0>] <0> [<f8954f0a>] <0> [<f8ea1b74>] <0> [<f8ed52f5>] <0> [<f8ea2416>] <0> [<f8ea15fd>] <0> [<f8ea16d3>] <0> [<c030f796>] <0> [<c030f87e>] <0> [<c036653e>] <0> [<c0366623>] <0> [<c0413467>] <0> [<c03666ec>] <0> [<c0366732>] <0> [<c0365cd8>] <0> [<c036646d>] <0> [<c03666ec>] <0> [<c0365f9a>] <0> [<c030f9dc>] <0> [<c013915d>] <0> [<f893e000>] <0> [<c0102d39>] <0> =======================
Code: f9 02 b8 8b e5 ed f8 eb 17 ba 90 e5 ed f8 eb 35 83 e1 0f ba 93 e5 ed f8 83 f9 02 b8 9d e5 ed f8 0f 45 d0 eb 20 f6 43 15 10 74 03 <83> 0a 04 83 e1 0f ba a1 e5 ed f8 83 f9 02 b8 ab e5 ed f8 eb e0
EIP: [<f8ed5700>] SS:ESP 0068:c226ccf4
<6>EXT3 FS on hda3, internal journal
Adding 2096472k swap on /dev/hda2. Priority:-1 extents:1 across:2096472k
Real Time Clock Driver v1.12ac |
Any help would be greatly appreciated. This machine does not boot with network from the LiveCD, it reports that
it cannot start the network. |
|
Back to top |
|
|
likhary n00b
Joined: 12 Nov 2008 Posts: 1
|
Posted: Thu Nov 13, 2008 5:52 pm Post subject: |
|
|
I can't seem to get my head round the file/directory structure ..... I'll get there eventually but this problem is stopping me from doing any real work on Linux - because I can't load any apps without acces to the net _________________ registry cleaner |
|
Back to top |
|
|
ashish3323 n00b
Joined: 01 Jul 2009 Posts: 6
|
Posted: Wed Jul 01, 2009 9:26 am Post subject: Re: "Netmount" can't get the network to start at a |
|
|
mrpotatohead wrote: | Ok - please be gentle -it's taken me two days to get a system that will actually boot! But I cannot get the network to fire up.
I installed from a CD and whilst I was doing that the network did work....
I do not know any commands at all.. I can follow explicit instructions only. So if you need me to list something you'll probably have to tell me where it is..
Contents of /etc/conf.d/net looks something like this:
iface_eth0="dhcp"
dhcpcd_eth0="-N"
dhcpcd-ETH0="-HD"
although I have tried other combinations. When I reboot i get the following error message:
ERROR: Problem starting needed services
"Netmount" was not started
I checked other threads, and found one that was sort of related, but I couldn't understand what was being said/asked. I did try one command that indicated that 'netmount = default' - but now I can't remember the ruddy command.
Help.............. |
I have Gentoo 2008 (AMD64)installed on my PC.My PC configuration is
"Intel Quad Core Processor 9300 2.5 Ghz,
ASUS P5N-E-SLI,
4 GB RAM 800 Mhz,
With Graphics Card 8600 GT.
I have NVIDIA network card inbuilt in my Motherboard. But the LAN is not working.I am completely New to Gentoo or even to Linux,
My Friend have installed Gentoo 2008 on my PC.So kindly help how can i install the LAN driver on my PC than i can connect to Internet and others PC connected through LAN. |
|
Back to top |
|
|
hariya123 n00b
Joined: 18 Jul 2009 Posts: 3 Location: India
|
Posted: Sun Jul 19, 2009 9:11 am Post subject: |
|
|
I have a similar probelm.
/sbin/ifconfig works fine from the liveCD. However after booting from the hard disk, it fails to detect eth0 only the lo is displayed.
on running lspci from live CD, it says command not found!
lsmod gives a big list.
Please someone help me... _________________ Siddhirbhavati Karmajah |
|
Back to top |
|
|
hariya123 n00b
Joined: 18 Jul 2009 Posts: 3 Location: India
|
Posted: Sun Jul 19, 2009 10:47 am Post subject: |
|
|
Quote: | starting eth0
Bringing up eth0
dhcp
network interface eth0 does not exit
please verify hardware or kernel module (driver)
ERROR: cannot start netmount as net.eth0 could not start
|
I too get a similar display when I type /etc/init.d/net.eth0 start
/sbin/ifconfig when given from the liveCD session gives
eth0
.........................................
lo
.........................................
wlan0
.........................................
wmaster0
.........................................
however when I boot through the hard disk and give the same command the follwing output is generated
lo
..........................................
it means that the driver that has been installed is wrong?
ok
So I went through the thread. Someone had suggested running 'lspci' and 'lsmod' during a liveCD as well as a harddisk boot session.When I try to run lspci through the liveCD session, I get the following error
"bash: lspci: command not found"
lsmod lists a number of options. However, when grep'ed with "Ethernet" or "eth0" or "network" nothing turns out
I haven't tried running the command during the liveCD session because I thought the effort was futile as I don't know which driver was used during the liveCD session.
Please help me out. My GDM is also not starting. Meaning the kernel that I am using is really bad. But I can't fix the problem without getting the network working _________________ Siddhirbhavati Karmajah |
|
Back to top |
|
|
hariya123 n00b
Joined: 18 Jul 2009 Posts: 3 Location: India
|
Posted: Sun Jul 19, 2009 11:08 am Post subject: |
|
|
ok fixed the lspci thing.
On booting from hard disk
Quote: | lspci | grep Ethernet
05:00.0 Ethernet controller: Marvell Technology Group Ltd. Unknown device 4353 (rev 14) |
What does it mean? and what can I do to fix the problem?
also
Code: |
lsmod
Module Size Used by
ipv6 239204 14
snd_pcm_oss 38208 0
snd_mixer_oss 17504 1 snd_pcm_oss
snd_seq_oss 31808 0
snd_seq_midi_event 8992 1 snd_seq_oss
snd_seq 49104 4 snd_seq_oss,snd_seq_midi_event
snd_ymfpci 61344 0
snd_vx222 14944 0
snd_vx_lib 32064 1 snd_vx222
snd_via82xx_modem 16296 0
snd_via82xx 29048 0
snd_trident 41892 0
snd_sonicvibes 23136 0
snd_rme9652 27648 0
snd_rme96 23844 0
snd_rme32 22880 0
snd_riptide 26548 0
snd_pcxhr 36288 0
snd_nm256 70528 0
snd_mona 29380 0
snd_mixart 36128 0
snd_mia 29988 0
snd_maestro3 25796 0
snd_layla24 32868 0
snd_layla20 30052 0
snd_korg1212 40740 0
snd_intel8x0m 18892 0
snd_intel8x0 34108 0
snd_indigoio 23492 0
snd_indigodj 22820 0
snd_indigo 22788 0
snd_ice1724 72140 0
snd_ak4114 11456 1 snd_ice1724
snd_pt2258 6048 1 snd_ice1724
snd_ice1712 59156 0
snd_ice17xx_ak4xxx 5984 2 snd_ice1724,snd_ice1712
snd_ak4xxx_adda 9760 3 snd_ice1724,snd_ice1712,snd_ice17xx_ak4xxx
snd_cs8427 10432 1 snd_ice1712
snd_i2c 7360 4 snd_ice1724,snd_pt2258,snd_ice1712,snd_cs8427
snd_hdspm 40448 0
snd_hdsp 48804 0
snd_hda_intel 278656 0
snd_gina24 29668 0
snd_gina20 25892 0
snd_fm801 19648 0
snd_es1968 29696 0
snd_es1938 23300 0
snd_ens1371 26624 0
snd_ens1370 21312 0
snd_ak4531_codec 10752 1 snd_ens1370
snd_emu10k1x 19940 0
snd_emu10k1 128288 0
snd_util_mem 6560 2 snd_trident,snd_emu10k1
snd_echo3g 33220 0
snd_darla24 24516 0
snd_darla20 22180 0
snd_cs5535audio 16476 0
snd_cs5530 7748 0
snd_sb16_dsp 11968 1 snd_cs5530
snd_cs46xx 81736 0
snd_cs4281 22752 0
snd_cmipci 36224 0
snd_ca0106 34432 0
snd_bt87x 16996 0
snd_azt3328 22720 0
snd_au8830 49396 0
snd_au8820 32512 0
snd_au8810 44180 0
snd_atiixp_modem 17480 0
snd_atiixp 21068 0
snd_als4000 16576 0
snd_sb_common 18144 3 snd_cs5530,snd_sb16_dsp,snd_als4000
gameport 16520 17 snd_ymfpci,snd_via82xx,snd_trident,snd_sonicvibes,snd_riptide,snd_es1968,snd_es1938,snd_ens1371,
snd_ens1370,snd_cs46xx,snd_cs4281,snd_cmipci,snd_azt3328,snd_au8830,snd_au8820,snd_au8810,snd_als4000
snd_opl3_lib 11840 9 snd_ymfpci,snd_sonicvibes,snd_riptide,snd_fm801,snd_es1938,snd_cs4281,snd_cmipci,snd_azt3328,snd_als4000
snd_hwdep 10820 4 snd_hdspm,snd_hdsp,snd_emu10k1,snd_opl3_lib
snd_mpu401_uart 9952 16 snd_ymfpci,snd_via82xx,snd_trident,snd_sonicvibes,snd_riptide,snd_ice1724,snd_ice1712,snd_fm801,snd_es1968,
snd_es1938,snd_cmipci,snd_azt3328,snd_au8830,snd_au8820,snd_au8810,snd_als4000
snd_rawmidi 24768 14 snd_mia,snd_layla24,snd_layla20,snd_hdspm,snd_hdsp,snd_ens1371,snd_ens1370,snd_emu10k1x,snd_emu10k1,
snd_echo3g,snd_cs46xx,snd_cs4281,snd_ca0106,snd_mpu401_uart
snd_seq_device 9804 6 snd_seq_oss,snd_seq,snd_trident,snd_emu10k1,snd_opl3_lib,snd_rawmidi
snd_als300 12964 0
snd_ali5451 24108 0
snd_ad1889 15456 0
snd_ac97_codec 96164 28 snd_ymfpci,snd_via82xx_modem,snd_via82xx,snd_trident,snd_riptide,snd_nm256,snd_maestro3,snd_intel8x0m,
snd_intel8x0,snd_ice1724,snd_ice1712,snd_fm801,snd_es1968,snd_ens1371,snd_emu10k1x,snd_emu10k1,
snd_cs5535audio,snd_cs46xx,snd_cs4281,snd_ca0106,snd_au8830,snd_au8820,snd_au8810,snd_atiixp_modem,
snd_atiixp,snd_als300,snd_ali5451,snd_ad1889
snd_pcm 69252 61 snd_pcm_oss,snd_ymfpci,snd_vx_lib,snd_via82xx_modem,snd_via82xx,snd_trident,snd_sonicvibes,snd_rme9652,
snd_rme96,snd_rme32,snd_riptide,snd_pcxhr,snd_nm256,snd_mona,snd_mixart,snd_mia,snd_maestro3,snd_layla24,
snd_layla20,snd_korg1212,snd_intel8x0m,snd_intel8x0,snd_indigoio,snd_indigodj,snd_indigo,snd_ice1724,
snd_ak4114,snd_ice1712,snd_hdspm,snd_hdsp,snd_hda_intel,snd_gina24,snd_gina20,snd_fm801,snd_es1968,
snd_es1938,snd_ens1371,snd_ens1370,snd_emu10k1x,snd_emu10k1,snd_echo3g,snd_darla24,snd_darla20,
snd_cs5535audio,snd_sb16_dsp,snd_cs46xx,snd_cs4281,snd_cmipci,snd_ca0106,snd_bt87x,snd_azt3328,
snd_au8830,snd_au8820,snd_au8810,snd_atiixp_modem,snd_atiixp,snd_als4000,snd_als300,snd_ali5451,
snd_ad1889,snd_ac97_codec
snd_timer 23300 6 snd_seq,snd_ymfpci,snd_emu10k1,snd_azt3328,snd_opl3_lib,snd_pcm
snd 51268 79 snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_ymfpci,snd_vx222,snd_vx_lib,snd_via82xx_modem,
snd_via82xx,snd_trident,snd_sonicvibes,snd_rme9652,snd_rme96,snd_rme32,snd_riptide,snd_pcxhr,snd_nm256,
snd_mona,snd_mixart,snd_mia,snd_maestro3,snd_layla24,snd_layla20,snd_korg1212,snd_intel8x0m,snd_intel8x0,
snd_indigoio,snd_indigodj,snd_indigo,snd_ice1724,snd_ak4114,snd_pt2258,snd_ice1712,snd_ak4xxx_adda,
snd_cs8427,snd_i2c,snd_hdspm,snd_hdsp,snd_hda_intel,snd_gina24,snd_gina20,snd_fm801,snd_es1968,
snd_es1938,snd_ens1371,snd_ens1370,snd_ak4531_codec,snd_emu10k1x,snd_emu10k1,snd_echo3g,snd_darla24,
snd_darla20,snd_cs5535audio,snd_cs5530,snd_sb16_dsp,snd_cs46xx,snd_cs4281,snd_cmipci,snd_ca0106,
snd_bt87x,snd_azt3328,snd_au8830,snd_au8820,snd_au8810,snd_atiixp_modem,snd_atiixp,snd_als4000,
snd_sb_common,snd_opl3_lib,snd_hwdep,snd_mpu401_uart,snd_rawmidi,snd_seq_device,snd_als300,snd_ali5451,
snd_ad1889,snd_ac97_codec,snd_pcm,snd_timer
soundcore 9600 1 snd
snd_page_alloc 12040 36 snd_ymfpci,snd_via82xx_modem,snd_via82xx,snd_trident,snd_rme9652,snd_riptide,snd_pcxhr,snd_mona,
snd_mixart,snd_mia,snd_layla24,snd_layla20,snd_korg1212,snd_intel8x0m,snd_intel8x0,snd_indigoio,snd_indigodj,
snd_indigo,snd_hdsp,snd_hda_intel,snd_gina24,snd_gina20,snd_es1968,snd_ens1370,snd_emu10k1x,snd_emu10k1,
snd_echo3g,snd_darla24,snd_darla20,snd_cs5535audio,snd_cs46xx,snd_ca0106,snd_bt87x,snd_atiixp_modem,
snd_atiixp,snd_pcm
ac97_bus 4096 1 snd_ac97_codec
tg3 106244 0
e1000 114368 0
raid10 24512 0
raid456 124176 0
async_memcpy 4736 1 raid456
async_xor 5984 1 raid456
xor 16456 2 raid456,async_xor
async_tx 9836 3 raid456,async_memcpy,async_xor
raid1 24608 0
raid0 10112 0
dm_bbr 14080 0
dm_snapshot 19172 0
dm_mirror 23744 0
dm_mod 58116 3 dm_bbr,dm_snapshot,dm_mirror
sbp2 23912 0
ohci1394 32592 0
ieee1394 87384 2 sbp2,ohci1394
sl811_hcd 14048 0
usbhid 30272 0
ohci_hcd 26724 0
ssb 33092 1 ohci_hcd
uhci_hcd 25520 0
usb_storage 79904 1
ehci_hcd 34572 0
usbcore 136300 7 sl811_hcd,usbhid,ohci_hcd,uhci_hcd,usb_storage,ehci_hcd
lpfc 215952 0
qla2xxx 163524 0
megaraid_sas 29712 0
megaraid_mbox 32400 0
megaraid_mm 12512 1 megaraid_mbox
megaraid 38856 0
aacraid 64036 0
sx8 19660 0
DAC960 68168 0
cciss 36772 0
cpqarray 22148 0
3w_9xxx 33476 0
3w_xxxx 27040 0
mptsas 37448 0
scsi_transport_sas 31584 1 mptsas
mptfc 19940 0
scsi_transport_fc 43556 3 lpfc,qla2xxx,mptfc
mptspi 22056 0
mptscsih 35360 3 mptsas,mptfc,mptspi
mptbase 72836 4 mptsas,mptfc,mptspi,mptscsih
atp870u 29632 0
dc395x 33612 0
qla1280 117868 0
dmx3191d 14176 0
sym53c8xx 72244 0
qlogicfas408 8896 0
aha152x 36720 0
advansys 79200 0
initio 19044 0
BusLogic 67284 0
arcmsr 24256 0
aic7xxx 158872 0
aic79xx 234808 0
scsi_transport_spi 24928 6 mptspi,dmx3191d,sym53c8xx,aha152x,aic7xxx,aic79xx
sg 35088 0
pdc_adma 11652 0
sata_inic162x 14180 0
sata_mv 22984 0
ahci 28324 1
sata_qstor 11908 0
sata_vsc 10660 0
sata_uli 9508 0
sata_sis 10660 0
sata_sx4 14564 0
sata_nv 27208 0
sata_via 13476 0
sata_svw 9732 0
sata_sil24 18052 0
sata_sil 13000 0
sata_promise 15076 0
scsi_wait_scan 3360 0
pata_pcmcia 15616 0
pcmcia 39308 2 ssb,pata_pcmcia
b1 25024 0
kernelcapi 40340 1 b1
pcmcia_core 39348 2 pata_pcmcia,pcmcia
firmware_class 11264 20 snd_vx_lib,snd_riptide,snd_pcxhr,snd_mona,snd_mixart,snd_mia,snd_layla24,snd_layla20,snd_indigoio,snd_indigodj,
snd_indigo,snd_hdsp,snd_gina24,snd_gina20,snd_emu10k1,snd_echo3g,snd_darla24,snd_darla20,qla2xxx,pcmcia |
Someone please help me!
Split several long lines in the lsmod output and switched the tags wrapping it from quote to code to preserve the indentation of the split lines. -- desultory _________________ Siddhirbhavati Karmajah |
|
Back to top |
|
|
mwhite n00b
Joined: 26 Jan 2008 Posts: 10
|
Posted: Tue Sep 22, 2009 10:20 pm Post subject: |
|
|
I've just installed Gentoo from the 2008 Livecd and I have the same issue with eth0 not being recognized by the system. While booted via the liveCD, it functioned fine. This is a virtual machine on an ESX3.0 system. I have eight previously installed Gentoo servers on this VM host so I know there's nothing wrong with my underlying setup. I'd love to provide the output for lspci, but that command doesn't seem to be installed on my system.
The exact error as seen during bootup:
* Starting syslog-ng ...
* Starting eth0
* Bringing up eth0
* 172.17.202.174
* network interface eth0 does not exist
* Please verify hardware or kernel module (driver)
* ERROR: cannot start netmount as net.eth0 could not start
BTW, the card should be seen as an AMD Am79C970A
Thanks in advance. |
|
Back to top |
|
|
mwhite n00b
Joined: 26 Jan 2008 Posts: 10
|
Posted: Tue Sep 22, 2009 10:33 pm Post subject: |
|
|
Looks like I posted too soon. I was able to figure out which modules to use based on the lsmod output on one of my other virtual machines. The needed modules were: mii and pcnet32
FWIW, I"ve had ton of trouble with this live CD. It's a POS IMO. I didn't go with the minimum install because it's a pain to get the drives setup in advance on a virtual machine. |
|
Back to top |
|
|
Arnaudv6 n00b
Joined: 18 Jul 2008 Posts: 46
|
Posted: Sat May 22, 2010 8:21 am Post subject: |
|
|
edited for translation... sorry... hadn't noticed I was reading english...
I've got a very basic problem; still I just can't manage to solve it:
g**gle helps too much : hard to find this exact case in that many results...
Problem : my localhost / 127.0.0.1 is not addressed correctly:
typing this as root works fine:
Code: | ifconfig lo 127.0.0.1 |
but
Code: | $ route add 127.0.0.1
SIOCADDRT: No such device |
Till now I was used to type this ifconfig before any network deamon start, like apache...
But I switched yesterday to MPC for listenning music and it is more critical.
I'm using WICD, as network manager deamon, so launched services are:
Code: | $ rc-update show
bootmisc | boot
checkfs | boot
checkroot | boot
clock | boot
consolefont | boot
hald | default
hostname | boot
keymaps | boot
local | default nonetwork
localmount | boot
modules | boot
mpd | default
rmnologin | boot
udev-postmount | default
urandom | boot
wicd | default
xdm | default |
Code: | $ ifconfig
eth0 Lien encap:Ethernet HWaddr 00:02:3f:be:44:09
inet adr:192.168.1.2 Bcast:192.168.1.255 Masque:255.255.255.0
adr inet6: fe80::202:3fff:febe:4409/64 Scope:Lien
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3548 errors:0 dropped:0 overruns:0 frame:0
TX packets:3682 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:2713233 (2.5 MiB) TX bytes:444747 (434.3 KiB)
Interruption:10
eth1 Lien encap:Ethernet HWaddr 00:04:23:79:b6:6c
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interruption:10 Adresse de base:0xa000 Mémoire:d0000000-d0000fff |
Code: | $ ifconfig lo
lo Lien encap:Boucle locale
LOOPBACK MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) |
Code: | cat /etc/conf.d/net
# This blank configuration will automatically use DHCP for any net.*
# scripts in /etc/init.d. To create a more complete configuration,
# please review /etc/conf.d/net.example and save your configuration
# in /etc/conf.d/net (this file :]!).
dns_domain_lo="homenetwork"
config_eth0=( "dhcp" ) |
Code: | cat /etc/hosts
# /etc/hosts: Local Host Database
127.0.0.1 arpent.homenetwork arpent localhost
|
Code: | $ cat /etc/conf.d/hostname
# /etc/conf.d/hostname
# Set to the hostname of this machine
HOSTNAME="arpent"
|
Voilà, if somone could help me to burry that topic quickly,
with kind regards
Arnaudv6 |
|
Back to top |
|
|
Arnaudv6 n00b
Joined: 18 Jul 2008 Posts: 46
|
Posted: Tue May 25, 2010 4:04 pm Post subject: |
|
|
nobody?
please help me |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
|