View previous topic :: View next topic |
Author |
Message |
pti-rem Guru
Joined: 14 Oct 2011 Posts: 472
|
Posted: Wed Nov 26, 2014 3:02 pm Post subject: [SSD] Crucial MX100 512 Go et adaptateur DVD slim (posé) |
|
|
Salut
Je voudrais remplacer mon DVD slim du portable Asus n73sm par cet ensemble et je vous demande votre avis et aussi une confirmation pour savoir si ça peut marcher ; C'est pour placer mes captures TNT .ts et les travailler.
Mon avis c'est que je me ferai un beau cadeau et que ça devrait marcher en 6Gbps ; Les disques 0 et 1 sont en sata300
Je pense prendre le tout chez matériel.net ; si peu de différence ... Et je suis sûr d'avoir la version boîte du ssd (avec l'adaptateur 9.5 mm) ; Le Crucial MX100 fait 7 mm d'épais.
Avec l'adaptateur Akasa N.Stor - Baie de remplacement SATA HDD
Une personne de chez matériel.net que j'ai eu au téléphone m'indique qu'il peut y avoir un problème de dimension de l'adaptateur, suivant les machines.
Code: | gazeau ~ # lspci -s 00:1f.2 -vv
00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device 11d7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 42
Region 0: I/O ports at e0b0 [size=8]
Region 1: I/O ports at e0a0 [size=4]
Region 2: I/O ports at e090 [size=8]
Region 3: I/O ports at e080 [size=4]
Region 4: I/O ports at e060 [size=32]
Region 5: Memory at df006000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee00000 Data: 40a1
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci |
Code: | [ 1.135636] ahci 0000:00:1f.2: version 3.0
[ 1.135778] ahci 0000:00:1f.2: irq 42 for MSI/MSI-X
[ 1.146535] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x7 impl SATA mode
[ 1.146595] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems apst
[ 1.151058] scsi0 : ahci
[ 1.151256] scsi1 : ahci
[ 1.151458] scsi2 : ahci
[ 1.151617] scsi3 : ahci
[ 1.151736] scsi4 : ahci
[ 1.151837] scsi5 : ahci
[ 1.151886] ata1: SATA max UDMA/133 abar m2048@0xdf006000 port 0xdf006100 irq 42
[ 1.151924] ata2: SATA max UDMA/133 abar m2048@0xdf006000 port 0xdf006180 irq 42
[ 1.151961] ata3: SATA max UDMA/133 abar m2048@0xdf006000 port 0xdf006200 irq 42
[ 1.151997] ata4: DUMMY
[ 1.152011] ata5: DUMMY
[ 1.152025] ata6: DUMMY |
Code: | rem@gazeau ~ $ dmesg | grep ata[123] | grep SATA
[ 1.151886] ata1: SATA max UDMA/133 abar m2048@0xdf006000 port 0xdf006100 irq 42
[ 1.151924] ata2: SATA max UDMA/133 abar m2048@0xdf006000 port 0xdf006180 irq 42
[ 1.151961] ata3: SATA max UDMA/133 abar m2048@0xdf006000 port 0xdf006200 irq 42
[ 1.456845] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.456864] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.458857] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) |
Code: | gazeau ~ # dmesg | grep 'scsi [012]'
[ 1.484110] scsi 0:0:0:0: Direct-Access ATA ST1000LM024 HN-M 0001 PQ: 0 ANSI: 5
[ 1.484677] scsi 1:0:0:0: Direct-Access ATA ST1000LM024 HN-M 0002 PQ: 0 ANSI: 5
[ 1.488050] scsi 2:0:0:0: CD-ROM Slimtype DVD A DS8A2S 6S21 PQ: 0 ANSI: 5 |
Last edited by pti-rem on Tue Dec 02, 2014 12:53 pm; edited 4 times in total |
|
Back to top |
|
|
pti-rem Guru
Joined: 14 Oct 2011 Posts: 472
|
Posted: Thu Nov 27, 2014 3:55 pm Post subject: |
|
|
Code: | gazeau ~ # hdparm -tT /dev/sda /dev/sdb
/dev/sda:
Timing cached reads: 18610 MB in 2.00 seconds = 9313.56 MB/sec
Timing buffered disk reads: 330 MB in 3.02 seconds = 109.30 MB/sec
/dev/sdb:
Timing cached reads: 18510 MB in 2.00 seconds = 9263.33 MB/sec
Timing buffered disk reads: 318 MB in 3.00 seconds = 105.94 MB/sec |
Donc je me trompe, je suis limité par SATA max UDMA/133 ? |
|
Back to top |
|
|
xaviermiller Bodhisattva
Joined: 23 Jul 2004 Posts: 8708 Location: ~Brussels - Belgique
|
Posted: Thu Nov 27, 2014 4:07 pm Post subject: |
|
|
Hello,
D'après tes logs, tu peux monter en SATA 3 Gpbs. Le résultat de hdparm est par rapport à ton disque dur installé. Si c'est un disque mécanique, ça me semble normal. _________________ Kind regards,
Xavier Miller |
|
Back to top |
|
|
pti-rem Guru
Joined: 14 Oct 2011 Posts: 472
|
Posted: Fri Nov 28, 2014 6:30 am Post subject: |
|
|
Hello,
oui, c'est un mécanique.
Tu vois que je peux monter à 3Gbps avec le "SATA link up 3.0 Gbps" ?
Le "AHCI 0001.0300 32 slots 6 ports 6 Gbps" n'indique pas-t'il que je puisse monter à 6Gbps ?
Il m'est curieux de voir le périphérique en AHCI 1.0 piloté en ahci version 3.0 ...
La version 1.0 du contrôleur n'aurait-t'elle pas une limitation intrinsèque ? 3Gbps, comme tu me l'indique ?
Je parcoure Serial ATA AHCI: Specification, Rev. 1.0
Quote: | 10.5 Interface Speed Support
The HBA indicates the maximum speed it can support via the CAP.ISS register. Software can further limit
the speed of a port by manipulating each port’s PxSCTL.SPD field to a lower value. If software writes a
value that is greater than the value in CAP.ISS, the actual speed negotiated will be limited by CAP.ISS,
as shown in the following table:
CAP.ISS - PxSCTL.SPD - Maximum Speed Negotiated
1h - 0h - 1.5 Gbps
1h - 1h - 1.5 Gbps
1h - 2h - 1.5 Gbps
2h - 0h - 3 Gbps
2h - 1h - 1.5 Gbps
2h - 2h - 3 Gbps |
Je me suis répondu, excuse-moi Xavier
J'ai de la chance. |
|
Back to top |
|
|
pti-rem Guru
Joined: 14 Oct 2011 Posts: 472
|
Posted: Tue Dec 02, 2014 11:54 am Post subject: |
|
|
Voilà, le ssd est monté ; voici les dernières infos
Code: | gazeau ~ # dmesg | grep ata3 && hdparm -Tt /dev/sdc
[ 1.148359] ata3: SATA max UDMA/133 abar m2048@0xdf006000 port 0xdf006200 irq 42
[ 1.454632] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.459638] ata3.00: ACPI cmd ef/90:06:00:00:00:00 (SET FEATURES) succeeded
[ 1.459640] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 1.459642] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 1.503347] ata3.00: supports DRM functions and may not be fully accessible
[ 1.508511] ata3.00: ATA-9: Crucial_CT512MX100SSD1, MU01, max UDMA/133
[ 1.509869] ata3.00: 1000215216 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.517479] ata3.00: ACPI cmd ef/90:06:00:00:00:00 (SET FEATURES) succeeded
[ 1.517483] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 1.518825] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 1.520644] ata3.00: supports DRM functions and may not be fully accessible
[ 1.533302] ata3.00: configured for UDMA/133
/dev/sdc:
Timing cached reads: 18222 MB in 2.00 seconds = 9119.07 MB/sec
Timing buffered disk reads: 694 MB in 3.00 seconds = 231.27 MB/sec |
Je ne suis pas à 300 MB/sec ; Mais pour charger de gros fichier .ts pour le ttt vidéo (de 3 à 20 Go environ) ça sera plus rapide.
Je me suis mal débrouillé avec la toute petite visserie ; cette période de l'année ne me convient pas.
J'espère qu'il va tenir la route longtemps.
La conclusion de l'article de Tom's Hardware Le SATA 3Gbit/s est-il assez rapide pour les SSD actuels ? me rassure un peu vis à vis de cet achat.
Édition : la navigation dans un .ts HD avec avidemux est bien plus souple et réactive ; Je n'ai plus de latence pour une avance d'image ou de trame ni même pour l'accéléré |
|
Back to top |
|
|
|