| View previous topic :: View next topic |
| Author |
Message |
Xywa
Veteran
Joined: 23 Jul 2005
Posts: 1631
Location: /mnt/Gentoo/Europe
|
 Posted: Sun Oct 19, 2014 2:20 pm Post subject: Huawei E3131 - how to run this under Gentoo? |
 |
|
Hi,
I have bought Huawei E3131, I am going on holiday and I would like to have an Internet from this.
http://www.huaweidevice.co.uk/devices/huawei-e3131/
On Gento wiki there is only manual for E367:
http://wiki.gentoo.org/wiki/Huawei_E367
What to do to run this? There is samle config file on Gento wiki form link above, can I find those details for my model form lsusb -v ?
| Code: | * sys-apps/usb_modeswitch
Latest version available: 2.2.0_p20140529
Latest version installed: 2.2.0_p20140529
|
| Code: | # lsusb
Bus 003 Device 002: ID 12d1:15ca Huawei Technologies Co., Ltd. E3131 3G/UMTS/HSPA+ Modem (Mass Storage Mode) |
and with usb_modeswitch
| Code: | Bus 003 Device 005: ID 12d1:1506 Huawei Technologies Co., Ltd. Modem/Networkcard
|
| Code: | # ls /dev/ttyUSB*
ls: cannot access /dev/ttyUSB*: No such file or directory
|
Update!!
This did the trick (thx NeddySeagoon)
https://forums.gentoo.org/viewtopic-t-942092-start-0.html
| Quote: | Shot in the dark ...Kod:
modprobe option
plug in your dongle, wait a few seconds and Kod:
ls /dev/ttyUSB*
The uppercase USB matters. |
| Code: | # ls /dev/ttyUSB*
/dev/ttyUSB0 /dev/ttyUSB1 /dev/ttyUSB2 |
| Code: | # wvdialconf
Editing `/etc/wvdial.conf'.
Scanning your serial ports for a modem.
Modem Port Scan<*1>: S0 S1 S2 S3
ttyUSB0<*1>: ATQ0 V1 E1 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 -- +CME ERROR: Incorrect parameters
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &D2 -- +CME ERROR: Incorrect parameters
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 +FCLASS=0 -- +CME ERROR: Incorrect parameters
ttyUSB0<*1>: Modem Identifier: ATI -- Manufacturer: huawei
ttyUSB0<*1>: Speed 9600: AT -- OK
ttyUSB0<*1>: Max speed is 9600; that should be safe.
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyUSB2<*1>: ATQ0 V1 E1 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 -- +CME ERROR: Incorrect parameters
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &D2 -- +CME ERROR: Incorrect parameters
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 +FCLASS=0 -- +CME ERROR: Incorrect parameters
ttyUSB2<*1>: Modem Identifier: ATI -- Manufacturer: huawei
ttyUSB2<*1>: Speed 9600: AT -- OK
ttyUSB2<*1>: Max speed is 9600; that should be safe.
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 -- OK
Found a modem on /dev/ttyUSB0.
/etc/wvdial.conf<Warn>: Can't open '/etc/wvdial.conf' for reading: No such file or directory
/etc/wvdial.conf<Warn>: ...starting with blank configuration.
Modem configuration written to /etc/wvdial.conf.
ttyUSB0<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0"
ttyUSB2<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0"
|
But how to configure this?
| Code: | # wvdial
--> WvDial: Internet dialer version 1.61
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0
ATQ0 V1 E1 S0=0
OK
--> Modem initialized.
--> Configuration does not specify a valid phone number.
--> Configuration does not specify a valid login name.
--> Configuration does not specify a valid password. |
|
|
| Back to top |
|
 |
Pearlseattle
Apprentice
Joined: 04 Oct 2007
Posts: 162
Location: Switzerland
|
| Posted: Sun Nov 09, 2014 5:37 pm Post subject: |
|
|
Hi
A long time ago I posted some guide about this kind of task and just today I edited the article adding some user's comments and then found as well your post (in the 0-reply posts section).
Therefore, what you might have to do is what I mentioned here under "5-Prepare the dialer":
http://www.blah-blah.ch/it/how-to-s/install-a-huawei-e1762-on-gentoo/#preparedialer
Just don't ask me anythiing about what I wrote there - it was 4 years ago  . |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
Networking & Security
