View previous topic :: View next topic |
Author |
Message |
snikkers n00b
Joined: 25 Jan 2012 Posts: 15
|
Posted: Sun Jan 20, 2013 10:37 pm Post subject: konfigurieren des rtl8367rb sitches (ralink SoC board) |
|
|
hi leute,
habe auf unserem board (rt3662f cpu, mips32el) gentoo gebaut und hänge nun beim netzwerk fest. der lan switch (rtl8367rb) treiber konnte mit einem openwrt system bereits erfolgreich getestet werden.
die konfiguration dazu:
Code: |
root@OpenWrt:/# cat /etc/config/network
config interface 'loopback'
option ifname 'lo'
option proto 'static'
option ipaddr '127.0.0.1'
option netmask '255.0.0.0'
config interface 'lan'
option ifname 'eth0.1'
option type 'bridge'
option proto 'static'
option ipaddr '192.168.1.1'
option netmask '255.255.255.0'
root@OpenWrt:/# |
die interfaces:
Code: |
root@OpenWrt:/# ifconfig
br-lan Link encap:Ethernet HWaddr 00:11:22:33:44:55
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:39 errors:0 dropped:0 overruns:0 frame:0
TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:5576 (5.4 KiB) TX bytes:182 (182.0 B)
eth0 Link encap:Ethernet HWaddr 00:11:22:33:44:55
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:364 errors:0 dropped:0 overruns:0 frame:0
TX packets:340 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:363648 (355.1 KiB) TX bytes:63799 (62.3 KiB)
Interrupt:5
eth0.1 Link encap:Ethernet HWaddr 00:11:22:33:44:55
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:39 errors:0 dropped:0 overruns:0 frame:0
TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:5576 (5.4 KiB) TX bytes:458 (458.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:378 errors:0 dropped:0 overruns:0 frame:0
TX packets:378 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:25352 (24.7 KiB) TX bytes:25352 (24.7 KiB)
|
kram aus /proc/net/vlan/*
Code: | root@OpenWrt:/# cat /proc/net/vlan/config
VLAN Dev name | VLAN ID
Name-Type: VLAN_NAME_TYPE_RAW_PLUS_VID_NO_PAD
eth0.1 | 1 | eth0
root@OpenWrt:/# cat /proc/net/vlan/eth0.1
eth0.1 VID: 1 REORDER_HDR: 1 dev->priv_flags: 4001
total frames received 13
total bytes received 1676
Broadcast/Multicast Rcvd 0
total frames transmitted 5
total bytes transmitted 274
Device: eth0
INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0
EGRESS priority mappings:
root@OpenWrt:/# |
kram aus /sys/devices/platform/*
Code: |
root@OpenWrt:/# ls /sys/devices/platform/*
/sys/devices/platform/uevent
/sys/devices/platform/alarmtimer:
driver modalias subsystem uevent
/sys/devices/platform/physmap-flash.0:
modalias subsystem uevent
/sys/devices/platform/ramips-wdt:
driver modalias subsystem uevent
/sys/devices/platform/ramips_eth.0:
driver ramips_mdio:05 ramips_mdio:0d ramips_mdio:15 ramips_mdio:1d
mdio_bus ramips_mdio:06 ramips_mdio:0e ramips_mdio:16 ramips_mdio:1e
modalias ramips_mdio:07 ramips_mdio:0f ramips_mdio:17 ramips_mdio:1f
ramips_mdio:00 ramips_mdio:08 ramips_mdio:10 ramips_mdio:18 subsystem
ramips_mdio:01 ramips_mdio:09 ramips_mdio:11 ramips_mdio:19 uevent
ramips_mdio:02 ramips_mdio:0a ramips_mdio:12 ramips_mdio:1a
ramips_mdio:03 ramips_mdio:0b ramips_mdio:13 ramips_mdio:1b
ramips_mdio:04 ramips_mdio:0c ramips_mdio:14 ramips_mdio:1c
/sys/devices/platform/regulatory.0:
modalias subsystem uevent
/sys/devices/platform/rt3883-ehci:
companion pools uframe_periodic_max
driver subsystem usb1
modalias uevent
/sys/devices/platform/rt3883-ohci:
driver modalias pools subsystem uevent usb2
/sys/devices/platform/rtl8367b:
driver modalias rtl8367b:01 rtl8367b:03 subsystem
mdio_bus rtl8367b:00 rtl8367b:02 rtl8367b:04 uevent
/sys/devices/platform/serial8250:
driver modalias subsystem tty uevent |
das ist die minimale konfiguration, mit der ich eine andere kiste anpingen kann.
jetzt muss ich dieses setup auf einem gentoo-system durchführen. wo soll ich anfangen und wie gehe ich am besten vor? das thema netzwerke ist leider nicht so meins. |
|
Back to top |
|
|
bell Guru
Joined: 27 Nov 2007 Posts: 510
|
Posted: Mon Jan 21, 2013 8:41 am Post subject: |
|
|
In der /usr/share/doc/openrc-0.11.8/net.example.bz2 gibt es einige Beispiele zum Thema VLAN. Konfiguriert wird in der /etc/conf.d/net. |
|
Back to top |
|
|
snikkers n00b
Joined: 25 Jan 2012 Posts: 15
|
Posted: Mon Jan 21, 2013 9:49 am Post subject: |
|
|
hi bell. standard vlan ist ja kein problem. auf diesem board funktioniert das leider nicht so einfach. sobald ich zu hause bin, versuche ich das problem besser zu beschreiben. |
|
Back to top |
|
|
|