View previous topic :: View next topic |
Author |
Message |
yarug Tux's lil' helper
Joined: 01 Dec 2004 Posts: 117 Location: NL
|
Posted: Mon Aug 15, 2005 9:36 pm Post subject: Install hangs while "Scanning for ata_piix" |
|
|
Hi there,
Trying to re-install Gentoo with the following drive config:
1 IDE 120GB HD on primary IDE channel as master
2 IDE CDROM drive on secondary IDE channel as master
3 S-ATA 160GB HD on first S-ATA channel
4 S-ATA 160GB HD on second S-ATA channel
I want to install Gentoo on both S-ATA disks and use the IDE disk as a backup device (it already contains a backup so it may not be touched during installation).
Made sure the BIOS recognised all drives and booted up the 2005.1 LiveCD. After the entering gentoo at the boot: prompt, the installation just hangs at
>> Loading modules
:: Scanning for ata_piix
I also tried boot: gentoo doscsi, but to no avail.
FWIW, this is on a A-Open AX4SG motherboard.
Does anyone know how to get past the Scanning for ata_piix? |
|
Back to top |
|
|
yarug Tux's lil' helper
Joined: 01 Dec 2004 Posts: 117 Location: NL
|
Posted: Mon Aug 15, 2005 10:20 pm Post subject: |
|
|
ps: If I specify boot: gentoo noload=ata_piix, setup continues but later hangs after
* Coldplugging PCI devices ... |
|
Back to top |
|
|
yarug Tux's lil' helper
Joined: 01 Dec 2004 Posts: 117 Location: NL
|
Posted: Tue Aug 16, 2005 11:16 pm Post subject: [Solved] Install hangs while "Scanning for ata_piix&quo |
|
|
Installed another motherboard (Asus p4P800SE) and this works fine IF I set these options in the BIOS under IDE config:
Onboard PCI IDE Operate Mode [Enhanced Mode]
Enhanced Mode Support On [S-ATA]
Configure S-ATA as RAID [No]
Changing Enhanced Mode Support On [S-ATA] to Enhanced Mode Support On [P-ATA+S-ATA] would give the same errors as in my first post.
Note that with the above BIOS settings, the BIOS does not recognize my P-ATA IDE drive (strangely enough it does recognise the CDROM drive), but the gentoo install does (so not a big deal really). |
|
Back to top |
|
|
Jovana n00b
Joined: 23 Nov 2005 Posts: 53
|
Posted: Wed Nov 23, 2005 9:12 pm Post subject: |
|
|
@yarug: Thx for posting your problem / solution. Same problem here, your solution did the trick! Thanks!! |
|
Back to top |
|
|
augury l33t
Joined: 22 May 2004 Posts: 722 Location: philadelphia
|
Posted: Thu Nov 24, 2005 1:41 pm Post subject: |
|
|
You should be able to leave raid on for dual channel sata. Your ata drive may not have spun up in time to be recognized. |
|
Back to top |
|
|
BeanoFTW n00b
Joined: 09 Oct 2012 Posts: 1
|
Posted: Tue Oct 09, 2012 10:25 pm Post subject: |
|
|
I know that this thread is over 6 years old, but I wanted to post a reply to those that googled this problem and reached this forum topic from there.
If you are installing Gentoo in Windows Virtual PC 2007 and are having this issue, follow these steps:
Restart the virtual machine, press DELETE to enter the setup interface.
Under the 'Power' tab, set Power Management/APM to disabled and set the ACPI Aware OS option to No.
Press F10 to exit setup and save the changes.
Good luck! |
|
Back to top |
|
|
|