| View previous topic :: View next topic |
| Author |
Message |
kbzium
Tux's lil' helper
Joined: 31 Jul 2012
Posts: 146
|
 Posted: Thu Aug 23, 2012 3:57 pm Post subject: Can't get USB 3.0 working! |
 |
|
Hello,
what are the options needed to be enabled in kernel config in order to get usb 3.0 working (2.0 is working fine)? I can't find it myself. Is there anything more that needs to be done?
Thanks! |
|
| Back to top |
|
 |
eccerr0r
Watchman
Joined: 01 Jul 2004
Posts: 9677
Location: almost Mile High in the USA
|
| Posted: Thu Aug 23, 2012 5:43 pm Post subject: |
|
|
I don't have any USB3 devices yet (soon will get something...very soon indeed...) but supposedly just CONFIG_USB_XHCI_HCD should do it...
_________________
Intel Core i7 2700K/Radeon R7 250/24GB DDR3/256GB SSD
What am I supposed watching? |
|
| Back to top |
|
|
monsm
Guru
Joined: 26 Sep 2007
Posts: 467
Location: London, UK
|
| Posted: Thu Aug 23, 2012 5:46 pm Post subject: |
|
|
Hi,
device drivers->Usb support->xHCI HCD (USB 3.0)
the text tag is:CONFIG_USB_XHCI_HCD
On my kernel (3.2.12) it still says experimental. I haven't actually got any 3.0 devices to test on, so can't say how the quality is...
Mons |
|
| Back to top |
|
|
eccerr0r
Watchman
Joined: 01 Jul 2004
Posts: 9677
Location: almost Mile High in the USA
|
| Posted: Fri Aug 24, 2012 1:47 am Post subject: |
|
|
I finally got to test USB3, it seems to work...
There were some debug statements:
| Code: | usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd
xhci_hcd 0000:02:00.0: WARN: short transfer on control ep
xhci_hcd 0000:02:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
xhci_hcd 0000:02:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
Initializing USB Mass Storage driver...
scsi6 : usb-storage 4-1:1.0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver uas
scsi 6:0:0:0: Direct-Access M4-CT128 M4SSD1 000F PQ: 0 ANSI: 4
sd 6:0:0:0: Attached scsi generic sg1 type 0
sd 6:0:0:0: [sdb] 250069680 512-byte logical blocks: (128 GB/119 GiB)
xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
xhci_hcd 0000:02:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
sd 6:0:0:0: [sdb] Write Protect is off
sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00
xhci_hcd 0000:02:00.0: WARN: Stalled endpoint
xhci_hcd 0000:02:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
sd 6:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
xhci_hcd 0000:02:00.0: WARN: Stalled endpoint |
but I was able to get 182MB/sec to that disk through USB3. No, this isn't going to be a permanent install but good for testing...
_________________
Intel Core i7 2700K/Radeon R7 250/24GB DDR3/256GB SSD
What am I supposed watching? |
|
| Back to top |
|
|
kbzium
Tux's lil' helper
Joined: 31 Jul 2012
Posts: 146
|
| Posted: Thu Sep 13, 2012 12:03 pm Post subject: |
|
|
Okay so it seems that my USB 3.0 ports are powered up now, after enabling those options in kernel. The thing is that i still cannot mount my external hard drive. It acts weird. fdisk -l reports other two drives and then freezes for about 10 seconds and then displays my external drive. Automounter fail to mount it for some reason. I've tried to modify fstab as this device is reported to be uba1 whatever that means, but with no success.
Any ideas? |
|
| Back to top |
|
|
|
Kernel & Hardware
