Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
Huawei e173 dosen't work
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Networking & Security
View previous topic :: View next topic  
Author Message
yendy
Tux's lil' helper
Tux's lil' helper


Joined: 03 May 2009
Posts: 78

PostPosted: Sat Nov 26, 2011 2:52 am    Post subject: Huawei e173 dosen't work Reply with quote

Hi All! I've followed the instructions this guidance to set up my Huwaei E173u-1 3G modem. It doesn't work (while under MS windows worked smoothly).

After pluging in this usb Huwaei modem the /var/log/messages yields something like this:
Code:
Nov 26 04:15:26 Ths kernel: usb 1-2: new high speed USB device using ehci_hcd and address 18
Nov 26 04:15:26 Ths kernel: scsi74 : usb-storage 1-2:1.0
Nov 26 04:15:26 Ths kernel: scsi75 : usb-storage 1-2:1.1
Nov 26 04:15:26 Ths usb_modeswitch: switching 12d1:1446 (HUAWEI Technology: HUAWEI Mobile)
Nov 26 04:15:26 Ths kernel: usb 1-2: USB disconnect, address 18
Nov 26 04:15:30 Ths kernel: usb 1-2: new high speed USB device using ehci_hcd and address 19
Nov 26 04:15:30 Ths kernel: option 1-2:1.0: GSM modem (1-port) converter detected
Nov 26 04:15:30 Ths kernel: usb 1-2: GSM modem (1-port) converter now attached to ttyUSB0
Nov 26 04:15:30 Ths kernel: option 1-2:1.3: GSM modem (1-port) converter detected
Nov 26 04:15:30 Ths kernel: usb 1-2: GSM modem (1-port) converter now attached to ttyUSB1
Nov 26 04:15:30 Ths kernel: option 1-2:1.4: GSM modem (1-port) converter detected
Nov 26 04:15:30 Ths kernel: usb 1-2: GSM modem (1-port) converter now attached to ttyUSB2
Nov 26 04:15:30 Ths kernel: scsi81 : usb-storage 1-2:1.5
Nov 26 04:15:30 Ths kernel: scsi82 : usb-storage 1-2:1.6
Nov 26 04:15:30 Ths /etc/init.d/net.ppp0[19183]: /dev/ttyUSB0 does not exist
Nov 26 04:15:30 Ths /etc/init.d/net.ppp0[19184]: Please verify hardware or kernel module (driver)
Nov 26 04:15:30 Ths /etc/init.d/net.ppp0[19096]: ERROR: net.ppp0 failed to start
Nov 26 04:15:31 Ths pppd[19303]: Plugin passwordfd.so loaded.
Nov 26 04:15:31 Ths pppd[19304]: pppd 2.4.5 started by root, uid 0
Nov 26 04:15:31 Ths /etc/init.d/net.ppp0[19201]: WARNING: net.ppp0 has started, but is inactive
Nov 26 04:15:31 Ths kernel: scsi 81:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
Nov 26 04:15:31 Ths kernel: scsi 82:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
Nov 26 04:15:31 Ths kernel: sd 82:0:0:0: Attached scsi generic sg2 type 0
Nov 26 04:15:31 Ths kernel: sr1: scsi-1 drive
Nov 26 04:15:31 Ths kernel: sr 81:0:0:0: Attached scsi CD-ROM sr1
Nov 26 04:15:31 Ths kernel: sr 81:0:0:0: Attached scsi generic sg3 type 5
Nov 26 04:15:31 Ths kernel: sd 82:0:0:0: [sdb] Attached SCSI removable disk
Nov 26 04:15:32 Ths chat[19316]: abort on (BUSY)
Nov 26 04:15:32 Ths chat[19316]: abort on (ERROR)
Nov 26 04:15:32 Ths chat[19316]: abort on (NO ANSWER)
Nov 26 04:15:32 Ths chat[19316]: abort on (NO CARRIER)
Nov 26 04:15:32 Ths chat[19316]: abort on (NO DIALTONE)
Nov 26 04:15:32 Ths chat[19316]: abort on (Invalid Login)
Nov 26 04:15:32 Ths chat[19316]: abort on (Login incorrect)
Nov 26 04:15:32 Ths chat[19316]: timeout set to 10 seconds
Nov 26 04:15:32 Ths chat[19316]: send (ATZ^M)
Nov 26 04:15:32 Ths pppd[19304]: Serial connection established.
Nov 26 04:15:32 Ths pppd[19304]: Using interface ppp0
Nov 26 04:15:32 Ths pppd[19304]: Connect: ppp0 <--> /dev/ttyUSB0
Nov 26 04:16:03 Ths pppd[19304]: LCP: timeout sending Config-Requests
Nov 26 04:16:03 Ths pppd[19304]: Connection terminated.
Nov 26 04:16:03 Ths pppd[19304]: Receive serial link is not 8-bit clean:
Nov 26 04:16:03 Ths pppd[19304]: Problem: all had bit 7 set to 0
Nov 26 04:16:04 Ths pppd[19304]: Modem hangup

afterwards it continues to produce such cyclic output (while modem keeps blinking blue LED):
Code:
Nov 26 03:45:32 Ths chat[9989]: abort on (BUSY)
Nov 26 03:45:32 Ths chat[9989]: abort on (ERROR)
Nov 26 03:45:32 Ths chat[9989]: abort on (NO ANSWER)
Nov 26 03:45:32 Ths chat[9989]: abort on (NO CARRIER)
Nov 26 03:45:32 Ths chat[9989]: abort on (NO DIALTONE)
Nov 26 03:45:32 Ths chat[9989]: abort on (Invalid Login)
Nov 26 03:45:32 Ths chat[9989]: abort on (Login incorrect)
Nov 26 03:45:32 Ths chat[9989]: timeout set to 10 seconds
Nov 26 03:45:32 Ths chat[9989]: send (ATZ^M)
Nov 26 03:45:32 Ths pppd[8785]: Serial connection established.
Nov 26 03:45:32 Ths pppd[8785]: Using interface ppp0
Nov 26 03:45:32 Ths pppd[8785]: Connect: ppp0 <--> /dev/ttyUSB0
Nov 26 03:46:03 Ths pppd[8785]: LCP: timeout sending Config-Requests
Nov 26 03:46:03 Ths pppd[8785]: Connection terminated.
Nov 26 03:46:03 Ths pppd[8785]: Receive serial link is not 8-bit clean:
Nov 26 03:46:03 Ths pppd[8785]: Problem: all had bit 7 set to 0
Nov 26 03:46:05 Ths pppd[8785]: Modem hangup
Nov 26 03:46:36 Ths chat[10139]: abort on (BUSY)
Nov 26 03:46:36 Ths chat[10139]: abort on (ERROR)
Nov 26 03:46:36 Ths chat[10139]: abort on (NO ANSWER)
Nov 26 03:46:36 Ths chat[10139]: abort on (NO CARRIER)
Nov 26 03:46:36 Ths chat[10139]: abort on (NO DIALTONE)
Nov 26 03:46:36 Ths chat[10139]: abort on (Invalid Login)
Nov 26 03:46:36 Ths chat[10139]: abort on (Login incorrect)
Nov 26 03:46:36 Ths chat[10139]: timeout set to 10 seconds
Nov 26 03:46:36 Ths chat[10139]: send (ATZ^M)
Nov 26 03:46:36 Ths pppd[8785]: Serial connection established.
Nov 26 03:46:36 Ths pppd[8785]: Using interface ppp0
Nov 26 03:46:36 Ths pppd[8785]: Connect: ppp0 <--> /dev/ttyUSB0
Nov 26 03:47:07 Ths pppd[8785]: LCP: timeout sending Config-Requests
Nov 26 03:47:07 Ths pppd[8785]: Connection terminated.
Nov 26 03:47:07 Ths pppd[8785]: Receive serial link is not 8-bit clean:
Nov 26 03:47:07 Ths pppd[8785]: Problem: all had bit 7 set to 0
Nov 26 03:47:08 Ths pppd[8785]: Modem hangup
Nov 26 03:47:39 Ths chat[10274]: abort on (BUSY)
Nov 26 03:47:39 Ths chat[10274]: abort on (ERROR)
Nov 26 03:47:39 Ths chat[10274]: abort on (NO ANSWER)
Nov 26 03:47:39 Ths chat[10274]: abort on (NO CARRIER)
Nov 26 03:47:39 Ths chat[10274]: abort on (NO DIALTONE)
Nov 26 03:47:39 Ths chat[10274]: abort on (Invalid Login)
Nov 26 03:47:39 Ths chat[10274]: abort on (Login incorrect)
Nov 26 03:47:39 Ths chat[10274]: timeout set to 10 seconds
Nov 26 03:47:39 Ths chat[10274]: send (ATZ^M)
Nov 26 03:47:39 Ths pppd[8785]: Serial connection established.
Nov 26 03:47:39 Ths pppd[8785]: Using interface ppp0
Nov 26 03:47:39 Ths pppd[8785]: Connect: ppp0 <--> /dev/ttyUSB0
Nov 26 03:48:10 Ths pppd[8785]: LCP: timeout sending Config-Requests
Nov 26 03:48:10 Ths pppd[8785]: Connection terminated.
Nov 26 03:48:10 Ths pppd[8785]: Receive serial link is not 8-bit clean:
Nov 26 03:48:10 Ths pppd[8785]: Problem: all had bit 7 set to 0
Nov 26 03:48:11 Ths pppd[8785]: Modem hangup
Nov 26 03:48:42 Ths chat[10472]: abort on (BUSY)
Nov 26 03:48:42 Ths chat[10472]: abort on (ERROR)
Nov 26 03:48:42 Ths chat[10472]: abort on (NO ANSWER)
Nov 26 03:48:42 Ths chat[10472]: abort on (NO CARRIER)
Nov 26 03:48:42 Ths chat[10472]: abort on (NO DIALTONE)
Nov 26 03:48:42 Ths chat[10472]: abort on (Invalid Login)
Nov 26 03:48:42 Ths chat[10472]: abort on (Login incorrect)
Nov 26 03:48:42 Ths chat[10472]: timeout set to 10 seconds
Nov 26 03:48:42 Ths chat[10472]: send (ATZ^M)
Nov 26 03:48:42 Ths pppd[8785]: Serial connection established.
Nov 26 03:48:42 Ths pppd[8785]: Using interface ppp0
Nov 26 03:48:42 Ths pppd[8785]: Connect: ppp0 <--> /dev/ttyUSB0
Nov 26 03:49:13 Ths pppd[8785]: LCP: timeout sending Config-Requests
Nov 26 03:49:13 Ths pppd[8785]: Connection terminated.
Nov 26 03:49:13 Ths pppd[8785]: Receive serial link is not 8-bit clean:
Nov 26 03:49:13 Ths pppd[8785]: Problem: all had bit 7 set to 0
Nov 26 03:49:15 Ths pppd[8785]: Modem hangup


Any PIN code variations in the /etc/conf.d/net pose no difference.
When PIN deactivated, (for my Polish provider ORANGE, APN: internet, dial nr: *99#)
the net file is as follows:
Code:
 dns_servers_ppp0=" '208.67.222.222' '208.67.220.220' "
  config_ppp0="ppp"
  link_ppp0="/dev/ttyUSB0"
  plugins_ppp0=""
  username_ppp0="nobody"
  password_ppp0="nothing"
  pppd_ppp0="lock defaultroute noipdefault noauth usepeerdns 460800"
  phone_number_ppp0="*99#"
  chat_ppp0="
         'ABORT' 'BUSY'
         'ABORT' 'ERROR'
         'ABORT' 'NO ANSWER'
         'ABORT' 'NO CARRIER'
         'ABORT' 'NO DIALTONE'
         'ABORT' 'Invalid Login'
         'ABORT' 'Login incorrect'
         'TIMEOUT' '10'
         '' 'ATZ'
         'OK' 'ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0'
         'OK' 'AT+CGDCONT=1,\\\"IP\\\",\\\"internet\\\"'
         'OK' 'ATDT\T'
         'CONNECT' ''
         '~--' ''
  "


Please help!
Back to top
View user's profile Send private message
yendy
Tux's lil' helper
Tux's lil' helper


Joined: 03 May 2009
Posts: 78

PostPosted: Tue Nov 29, 2011 1:14 pm    Post subject: Reply with quote

please, help...
nothing helps, I tried NetworkManager, wvdial...
I've read on one of many forums I've searched this USB modem should be blocked just after pluging in - to prevent switchnig its mode. How to achieve it? Why does not the tutorial from gentoo-wiki write anything about it?

Oh, maybe I should mention that before everytnig I upgraded modem's firmware to the Reliance3G's which was the only one I could find in the Internet. Maybe this branded firmware has its special features which prevent it from cooperating with linux?
Back to top
View user's profile Send private message
Logicien
l33t
l33t


Joined: 16 Sep 2005
Posts: 829
Location: Montréal

PostPosted: Tue Nov 29, 2011 1:46 pm    Post subject: Reply with quote

Hi,
I have an Huawai E1831. It work with Network Manager and Wvdial. I installed the usb_modeswitch utilities to be sure the USB stick is in the modem mode. You can have to unload the usbserial and the usb-storage modules to resolv a possible mode conflict. Than you list the vendor and the product ID's of the device with the command
Code:
lsusb -vvv | less

and you use them as parameters for the usbserial module and write this type of line in /etc/modprobe.d/modprobe.conf:
Code:
options usbserial product=0x1446 vendor=0x12d1

Replace with the good ID's. Now you can load the module
Code:
modprobe usbserial

At that point you should have wwan0 network card in plus of /dev/ttyUSB0 to 4. You configure your connexion with
Code:
wvdialconf

and edit the /etc/wvdial.conf file to uncomment the lines for user, password and phone with appropriate name and password that can be dummy and the phone number. Than
Code:
wvdial

work for me.
_________________
Paul
Back to top
View user's profile Send private message
yendy
Tux's lil' helper
Tux's lil' helper


Joined: 03 May 2009
Posts: 78

PostPosted: Tue Nov 29, 2011 4:14 pm    Post subject: Reply with quote

Thank you, Logicien.
However there are still problems.
Thirst, I can't unload 'usbserial' without unloading 'opiton' module too, since there is the dependancy of them. So I unloaded the two modules - was it what you meant?

Then I read what lsusb yields, it was:
....
Bus 001 Device 003: ID 12d1:1436 Huawei Technologies Co., Ltd.
so I created the /etc/modprobe.d/modprobe.conf file and enterred the corresponding line there:
options usbserial product=0x1436 vendor=0x12d1

Next, I did 'modprobe usbserial', and then issued 'wvdialconf' command:
Code:
~ # wvdialconf
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

Modem Port Scan<*1>: S0   S1   S2   S3   
WvModem<*1>: Cannot get information for serial port.
ttyUSB0<*1>: ATQ0 V1 E1 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyUSB0<*1>: Modem Identifier: ATI -- Manufacturer: huawei
ttyUSB0<*1>: Speed 9600: AT -- OK
ttyUSB0<*1>: Max speed is 9600; that should be safe.
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
WvModem<*1>: Cannot get information for serial port.
ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
WvModem<*1>: Cannot get information for serial port.
ttyUSB2<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB2<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB2<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
WvModem<*1>: Cannot get information for serial port.
ttyUSB3<*1>: ATQ0 V1 E1 -- OK
ttyUSB3<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB3<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB3<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyUSB3<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB3<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyUSB3<*1>: Modem Identifier: ATI -- Manufacturer: huawei
ttyUSB3<*1>: Speed 9600: AT -- OK
ttyUSB3<*1>: Max speed is 9600; that should be safe.
ttyUSB3<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
WvModem<*1>: Cannot get information for serial port.
ttyUSB4<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB4<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB4<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.

WvModem<*1>: Cannot get information for serial port.
ttyUSB5<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB5<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB5<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.

Found a modem on /dev/ttyUSB0.
Modem configuration written to /etc/wvdial.conf.
ttyUSB0<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
ttyUSB3<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"


and lastly the command 'wvdial' gives this:
Code:
~ # wvdial
--> WvDial: Internet dialer version 1.61
--> Warning: section [Dialer Defaults] does not exist in wvdial.conf.
--> Cannot open /dev/modem: No such file or directory
--> Cannot open /dev/modem: No such file or directory
--> Cannot open /dev/modem: No such file or directory


So why? :(
Back to top
View user's profile Send private message
Logicien
l33t
l33t


Joined: 16 Sep 2005
Posts: 829
Location: Montréal

PostPosted: Wed Nov 30, 2011 12:12 am    Post subject: Reply with quote

After writing the /etc/modprobe.d/modprobe.conf file it can be best to shutdown the machine then start it again. In /etc/wvdial.conf those lines should work:
Code:
[Dialer Defaults]
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
Phone = *99#
ISDN = 0
Username = dummy
Init1 = ATZ
Password = dummy
Modem = /dev/ttyUSB0
Baud = 9600

Check if you have the nodes /dev/ttyUSB0 to 4. dummy can be a real username and password instead. You problem can come from the fact that the symbolic link /dev/modem do not exist or do not point to /dev/ttyUSB0. So you have to do it manually almost at every boot or configure Udev to do it for you. Use the real node to the modem /dev/ttyUSB0 is good enough.

Edit: precise the ID of the vendor and product seem's to be facultative. My connexion work without any parameter passed to usbserial. Anyway, if you have more than one USB/Serial devices, Linux have to be able to use all of thems.
_________________
Paul
Back to top
View user's profile Send private message
yendy
Tux's lil' helper
Tux's lil' helper


Joined: 03 May 2009
Posts: 78

PostPosted: Wed Nov 30, 2011 9:56 pm    Post subject: Reply with quote

Logicien wrote:
In /etc/wvdial.conf those lines should work:
Code:
[Dialer Defaults]
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
Phone = *99#
ISDN = 0
Username = dummy
Init1 = ATZ
Password = dummy
Modem = /dev/ttyUSB0
Baud = 9600

Check if you have the nodes /dev/ttyUSB0 to 4. dummy can be a real username and password instead. You problem can come from the fact that the symbolic link /dev/modem do not exist or do not point to /dev/ttyUSB0.
No, Logicien, the main trouble of 'wvdial' is about it doesn't read the configuration file '/etc/wvdial.conf' at all!
Whatever is put in the file the 'wvdial' always yields the error it can't find any section, especially [Dialer Defaults]. Perhaps it is a bug, isn't it?
How did you the job not having such error messages?


Last edited by yendy on Wed Nov 30, 2011 10:46 pm; edited 1 time in total
Back to top
View user's profile Send private message
yendy
Tux's lil' helper
Tux's lil' helper


Joined: 03 May 2009
Posts: 78

PostPosted: Wed Nov 30, 2011 10:05 pm    Post subject: Reply with quote

It works at last! I really don't know why but it is good it came to life :)
Maybe it is because I updated the system, with the 'revdep-rebuld' command, maybe its about the other kernel 'ppp-...' modules I've configured too now (dispite no need of activating them was mentioned in the tutorial)... I really don't know what has happened - as almost no new settings arrived, e.g. the '/etc/conf.d/net file is the same.

It works with the "basic" configuration from this tutorial: http://en.gentoo-wiki.com/wiki/Huawei_E173
When this usb modem is plugged in then the '/var/log/messages' shows the following messages:
Code:


Nov 30 23:14:24 Ths kernel: usb 1-2: new high speed USB device using ehci_hcd and address 2
Nov 30 23:14:25 Ths kernel: Initializing USB Mass Storage driver...
Nov 30 23:14:25 Ths kernel: scsi2 : usb-storage 1-2:1.0
Nov 30 23:14:25 Ths kernel: scsi3 : usb-storage 1-2:1.1
Nov 30 23:14:25 Ths kernel: usbcore: registered new interface driver usb-storage
Nov 30 23:14:25 Ths kernel: USB Mass Storage support registered.
Nov 30 23:14:25 Ths usb_modeswitch: switching 12d1:1446 (HUAWEI Technology: HUAWEI Mobile)
Nov 30 23:14:25 Ths kernel: usb 1-2: USB disconnect, address 2
Nov 30 23:14:29 Ths kernel: usb 1-2: new high speed USB device using ehci_hcd and address 3
Nov 30 23:14:29 Ths kernel: scsi9 : usb-storage 1-2:1.5
Nov 30 23:14:29 Ths kernel: scsi10 : usb-storage 1-2:1.6
Nov 30 23:14:29 Ths kernel: usbcore: registered new interface driver usbserial
Nov 30 23:14:29 Ths kernel: USB Serial support registered for generic
Nov 30 23:14:29 Ths kernel: usbcore: registered new interface driver usbserial_generic
Nov 30 23:14:29 Ths kernel: usbserial: USB Serial Driver core
Nov 30 23:14:29 Ths kernel: USB Serial support registered for GSM modem (1-port)
Nov 30 23:14:29 Ths kernel: option 1-2:1.0: GSM modem (1-port) converter detected
Nov 30 23:14:29 Ths kernel: usb 1-2: GSM modem (1-port) converter now attached to ttyUSB0
Nov 30 23:14:29 Ths kernel: option 1-2:1.3: GSM modem (1-port) converter detected
Nov 30 23:14:29 Ths kernel: usb 1-2: GSM modem (1-port) converter now attached to ttyUSB1
Nov 30 23:14:29 Ths kernel: option 1-2:1.4: GSM modem (1-port) converter detected
Nov 30 23:14:29 Ths kernel: usb 1-2: GSM modem (1-port) converter now attached to ttyUSB2
Nov 30 23:14:29 Ths kernel: usbcore: registered new interface driver option
Nov 30 23:14:29 Ths kernel: option: v0.7.2:USB Driver for GSM modems
Nov 30 23:14:30 Ths /etc/init.d/net.ppp0[4999]: /dev/ttyUSB0 does not exist
Nov 30 23:14:30 Ths /etc/init.d/net.ppp0[5000]: Please verify hardware or kernel module (driver)
Nov 30 23:14:30 Ths /etc/init.d/net.ppp0[4904]: ERROR: net.ppp0 failed to start
Nov 30 23:14:30 Ths pppd[5136]: Plugin passwordfd.so loaded.
Nov 30 23:14:30 Ths kernel: PPP generic driver version 2.4.2
Nov 30 23:14:30 Ths pppd[5136]: Created /dev/ppp device node
Nov 30 23:14:30 Ths pppd[5139]: pppd 2.4.5 started by root, uid 0
Nov 30 23:14:30 Ths /etc/init.d/net.ppp0[5017]: WARNING: net.ppp0 has started, but is inactive
Nov 30 23:14:30 Ths kernel: scsi 9:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
Nov 30 23:14:30 Ths kernel: scsi 10:0:0:0: Direct-Access     HUAWEI   SD Storage       2.31 PQ: 0 ANSI: 2
Nov 30 23:14:30 Ths kernel: sd 10:0:0:0: Attached scsi generic sg2 type 0
Nov 30 23:14:30 Ths kernel: sr1: scsi-1 drive
Nov 30 23:14:30 Ths kernel: sr 9:0:0:0: Attached scsi CD-ROM sr1
Nov 30 23:14:30 Ths kernel: sr 9:0:0:0: Attached scsi generic sg3 type 5
Nov 30 23:14:30 Ths kernel: sd 10:0:0:0: [sdb] Attached SCSI removable disk
Nov 30 23:14:31 Ths chat[5151]: abort on (BUSY)
Nov 30 23:14:31 Ths chat[5151]: abort on (ERROR)
Nov 30 23:14:31 Ths chat[5151]: abort on (NO ANSWER)
Nov 30 23:14:31 Ths chat[5151]: abort on (NO CARRIER)
Nov 30 23:14:31 Ths chat[5151]: abort on (NO DIALTONE)
Nov 30 23:14:31 Ths chat[5151]: abort on (Invalid Login)
Nov 30 23:14:31 Ths chat[5151]: abort on (Login incorrect)
Nov 30 23:14:31 Ths chat[5151]: timeout set to 10 seconds
Nov 30 23:14:31 Ths chat[5151]: send (ATZ^M)
Nov 30 23:14:31 Ths chat[5151]: expect (OK)
Nov 30 23:14:31 Ths chat[5151]: ATZ^M^M
Nov 30 23:14:31 Ths chat[5151]: OK
Nov 30 23:14:31 Ths chat[5151]:  -- got it
Nov 30 23:14:31 Ths chat[5151]: send (AT+CPIN?^M)
Nov 30 23:14:31 Ths chat[5151]: expect (READY)
Nov 30 23:14:31 Ths chat[5151]: ^M
Nov 30 23:14:31 Ths chat[5151]: AT+CPIN?^M^M
Nov 30 23:14:31 Ths chat[5151]: +CPIN: READY
Nov 30 23:14:31 Ths chat[5151]:  -- got it
Nov 30 23:14:31 Ths chat[5151]: send (ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0^M)
Nov 30 23:14:32 Ths chat[5151]: expect (OK)
Nov 30 23:14:32 Ths chat[5151]: ^M
Nov 30 23:14:32 Ths chat[5151]: ^M
Nov 30 23:14:32 Ths chat[5151]: OK
Nov 30 23:14:32 Ths chat[5151]:  -- got it
Nov 30 23:14:32 Ths chat[5151]: send (AT+CGDCONT=1,\"IP\",\"internet\"^M)
Nov 30 23:14:32 Ths chat[5151]: expect (OK)
Nov 30 23:14:32 Ths chat[5151]: ^M
Nov 30 23:14:32 Ths chat[5151]: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0^M^M
Nov 30 23:14:32 Ths chat[5151]: OK
Nov 30 23:14:32 Ths chat[5151]:  -- got it
Nov 30 23:14:32 Ths chat[5151]: send (ATDT*99#^M)
Nov 30 23:14:32 Ths chat[5151]: expect (CONNECT)
Nov 30 23:14:32 Ths chat[5151]: ^M
Nov 30 23:14:32 Ths chat[5151]: AT+CGDCONT=1,"IP","internet"^M^M
Nov 30 23:14:32 Ths chat[5151]: OK^M
Nov 30 23:14:32 Ths chat[5151]: ATDT*99#^M^M
Nov 30 23:14:32 Ths chat[5151]: NO CARRIER
Nov 30 23:14:32 Ths chat[5151]:  -- failed
Nov 30 23:14:32 Ths chat[5151]: Failed (NO CARRIER)
Nov 30 23:14:32 Ths pppd[5139]: Connect script failed
Nov 30 23:15:04 Ths chat[5158]: abort on (BUSY)
Nov 30 23:15:04 Ths chat[5158]: abort on (ERROR)
Nov 30 23:15:04 Ths chat[5158]: abort on (NO ANSWER)
Nov 30 23:15:04 Ths chat[5158]: abort on (NO CARRIER)
Nov 30 23:15:04 Ths chat[5158]: abort on (NO DIALTONE)
Nov 30 23:15:04 Ths chat[5158]: abort on (Invalid Login)
Nov 30 23:15:04 Ths chat[5158]: abort on (Login incorrect)
Nov 30 23:15:04 Ths chat[5158]: timeout set to 10 seconds
Nov 30 23:15:04 Ths chat[5158]: send (ATZ^M)
Nov 30 23:15:04 Ths chat[5158]: expect (OK)
Nov 30 23:15:04 Ths chat[5158]: ATZ^M^M
Nov 30 23:15:04 Ths chat[5158]: OK
Nov 30 23:15:04 Ths chat[5158]:  -- got it
Nov 30 23:15:04 Ths chat[5158]: send (AT+CPIN?^M)
Nov 30 23:15:04 Ths chat[5158]: expect (READY)
Nov 30 23:15:04 Ths chat[5158]: ^M
Nov 30 23:15:04 Ths chat[5158]: AT+CPIN?^M^M
Nov 30 23:15:04 Ths chat[5158]: +CPIN: READY
Nov 30 23:15:04 Ths chat[5158]:  -- got it
Nov 30 23:15:04 Ths chat[5158]: send (ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0^M)
Nov 30 23:15:05 Ths chat[5158]: expect (OK)
Nov 30 23:15:05 Ths chat[5158]: ^M
Nov 30 23:15:05 Ths chat[5158]: ^M
Nov 30 23:15:05 Ths chat[5158]: OK
Nov 30 23:15:05 Ths chat[5158]:  -- got it
Nov 30 23:15:05 Ths chat[5158]: send (AT+CGDCONT=1,\"IP\",\"internet\"^M)
Nov 30 23:15:05 Ths chat[5158]: expect (OK)
Nov 30 23:15:05 Ths chat[5158]: ^M
Nov 30 23:15:05 Ths chat[5158]: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0^M^M
Nov 30 23:15:05 Ths chat[5158]: OK
Nov 30 23:15:05 Ths chat[5158]:  -- got it
Nov 30 23:15:05 Ths chat[5158]: send (ATDT*99#^M)
Nov 30 23:15:05 Ths chat[5158]: expect (CONNECT)
Nov 30 23:15:05 Ths chat[5158]: ^M
Nov 30 23:15:05 Ths chat[5158]: AT+CGDCONT=1,"IP","internet"^M^M
Nov 30 23:15:05 Ths chat[5158]: OK^M
Nov 30 23:15:05 Ths chat[5158]: ATDT*99#^M^M
Nov 30 23:15:05 Ths chat[5158]: CONNECT
Nov 30 23:15:05 Ths chat[5158]:  -- got it
Nov 30 23:15:05 Ths chat[5158]: send (^M)
Nov 30 23:15:05 Ths chat[5158]: expect (~)
Nov 30 23:15:05 Ths chat[5158]: ^M
Nov 30 23:15:15 Ths chat[5158]: alarm
Nov 30 23:15:15 Ths chat[5158]: send (^M)
Nov 30 23:15:15 Ths chat[5158]: send (^M)
Nov 30 23:15:15 Ths pppd[5139]: Serial connection established.
Nov 30 23:15:16 Ths pppd[5139]: Using interface ppp0
Nov 30 23:15:16 Ths pppd[5139]: Connect: ppp0 <--> /dev/ttyUSB0
Nov 30 23:15:17 Ths pppd[5139]: CHAP authentication succeeded
Nov 30 23:15:17 Ths pppd[5139]: CHAP authentication succeeded
Nov 30 23:15:17 Ths kernel: PPP BSD Compression module registered
Nov 30 23:15:17 Ths kernel: PPP Deflate Compression module registered
Nov 30 23:15:19 Ths pppd[5139]: Could not determine remote IP address: defaulting to 10.64.64.64
Nov 30 23:15:20 Ths pppd[5139]: local  IP address 91.94.17.184
Nov 30 23:15:20 Ths pppd[5139]: remote IP address 10.64.64.64
Nov 30 23:15:20 Ths pppd[5139]: primary   DNS address 79.163.127.70
Nov 30 23:15:20 Ths pppd[5139]: secondary DNS address 217.116.100.65
Nov 30 23:15:20 Ths /etc/init.d/net.ppp0[5214]: status: inactive


The only complaint remains - about modem's probably too long switching on, it takes about 1-2 minutes until the connection really is established. Under MS windows it took 11 seconds.
Is it the issue that, as we can see above, the modem seems to take 3 attempts before it actually connects?

To sum up, it is nice it works at last but it would be even nicer to know why. Any idea, Gentlemen?
Back to top
View user's profile Send private message
Double Click
Tux's lil' helper
Tux's lil' helper


Joined: 21 May 2004
Posts: 148

PostPosted: Sun Mar 25, 2012 7:43 am    Post subject: Reply with quote

Did you ever get it to work? I will need to setup my 3G Dongle as well and I have to say I am worried when looking through the forum post regarding this. My fallback would be to have the 3G dongle as a hardware pass-through on my Windows 7 guest but that will become a problem sooner or later if I cannot use the 3G dongle via Gentoo.

Seems Gentoo picks up mine at least but from there on there does not seem any straight forward way to configure it.

Quote:

usb 1-2: new high-speed USB device number 3 using ehci_hcd
usb 1-2: New USB device found, idVendor=12d1, idProduct=1446
usb 1-2: New USB device strings: Mfr=3, Product=2, SerialNumber=0
usb 1-2: Product: HUAWEI Mobile
usb 1-2: Manufacturer: HUAWEI Technology
scsi6 : usb-storage 1-2:1.0
scsi7 : usb-storage 1-2:1.1
usb 1-2: USB disconnect, device number 3
usb 1-2: new high-speed USB device number 4 using ehci_hcd
usb 1-2: New USB device found, idVendor=12d1, idProduct=14ac
usb 1-2: New USB device strings: Mfr=4, Product=3, SerialNumber=0
usb 1-2: Product: HUAWEI Mobile
usb 1-2: Manufacturer: HUAWEI Technology
scsi8 : usb-storage 1-2:1.5
scsi9 : usb-storage 1-2:1.6
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
cdc_ether 1-2:1.1: wwan0: register 'cdc_ether' at usb-0000:00:04.1-2, Mobile Broadband Network Device, 02:50:f3:00:00:00
usbcore: registered new interface driver cdc_ether
USB Serial support registered for GSM modem (1-port)
option 1-2:1.0: GSM modem (1-port) converter detected
usb 1-2: GSM modem (1-port) converter now attached to ttyUSB0
option 1-2:1.3: GSM modem (1-port) converter detected
usb 1-2: GSM modem (1-port) converter now attached to ttyUSB1
option 1-2:1.4: GSM modem (1-port) converter detected
usb 1-2: GSM modem (1-port) converter now attached to ttyUSB2
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
scsi 8:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
scsi 9:0:0:0: Direct-Access HUAWEI MMC Storage 2.31 PQ: 0 ANSI: 2
sr1: scsi-1 drive
sr 8:0:0:0: Attached scsi CD-ROM sr1
sr 8:0:0:0: Attached scsi generic sg2 type 5
sd 9:0:0:0: Attached scsi generic sg3 type 0
sd 9:0:0:0: [sdb] Attached SCSI removable disk

_________________
- To do a certain kind of thing, you have to be a certain kind of person
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Networking & Security All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum