| View previous topic :: View next topic |
| Author |
Message |
d2_racing Moderator


Joined: 25 Apr 2005 Posts: 13034 Location: Ste-Foy,Canada
|
Posted: Wed Sep 30, 2009 9:17 pm Post subject: problem with wlan0 is inactive and iwl3945 driver |
|
|
Hi everyone, I have a new problem on my box.
My wlan0 interface doesn't want to start when I run /etc/init.d/net.wlan0
I have net.wlan0 is started but inactive message.
For the record, I can run iwlist scan, so basically the wireless card is alive.
I'm running on ~arch amd64 box.
My /etc/wpa_supplicant/wpa_supplicant.conf is good since I was able to use my Wifi.
Any idea where to start searching ?
Thanks  _________________ Sysadmin of GentooQuébec.org
Wiki
Signature
IRC on Freenode : #gentoo-quebec |
|
| Back to top |
|
 |
audiodef Advocate


Joined: 06 Jul 2005 Posts: 4952
|
|
| Back to top |
|
 |
pappy_mcfae Watchman


Joined: 27 Dec 2007 Posts: 5807 Location: Pomona, California.
|
|
| Back to top |
|
 |
d2_racing Moderator


Joined: 25 Apr 2005 Posts: 13034 Location: Ste-Foy,Canada
|
|
| Back to top |
|
 |
d2_racing Moderator


Joined: 25 Apr 2005 Posts: 13034 Location: Ste-Foy,Canada
|
Posted: Thu Oct 01, 2009 1:09 am Post subject: |
|
|
I found one of the source of the problem.
To make my wireless working, I need to run this :
-Reboot my box.
| Code: |
# ifconfig wlan0 up
# /etc/init.d/net.wlan0 start
|
And nothing happens, but if I run this extra command, my wireless is working :
What is going on ??? _________________ Sysadmin of GentooQuébec.org
Wiki
Signature
IRC on Freenode : #gentoo-quebec |
|
| Back to top |
|
 |
d2_racing Moderator


Joined: 25 Apr 2005 Posts: 13034 Location: Ste-Foy,Canada
|
Posted: Thu Oct 01, 2009 1:10 am Post subject: |
|
|
| Code: |
[ 845.817271] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 870.601301] wlan0: authenticate with AP 00:0e:83:61:19:9b
[ 870.603081] wlan0: authenticated
[ 870.603089] wlan0: associate with AP 00:0e:83:61:19:9b
[ 870.605090] wlan0: RX AssocResp from 00:0e:83:61:19:9b (capab=0x421 status=0 aid=230)
[ 870.605098] wlan0: associated
[ 870.607663] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 881.512038] wlan0: no IPv6 routers present
|
| Code: |
gentootux ~ # wpa_cli status
Selected interface 'wlan0'
bssid=00:0e:83:61:19:9b
ssid=HolidayInnSelectMontreal
id=2
pairwise_cipher=NONE
group_cipher=NONE
key_mgmt=NONE
wpa_state=COMPLETED
ip_address=192.168.101.32
gentootux ~ #
|
| Code: |
gentootux ~ # iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
sit0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11abg ESSID:"HolidayInnSelectMontreal"
Mode:Managed Frequency:2.437 GHz Access Point: 00:0E:83:61:19:9B
Bit Rate=11 Mb/s Tx-Power=15 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=55/70 Signal level=-55 dBm Noise level=-127 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
gentootux ~ #
|
_________________ Sysadmin of GentooQuébec.org
Wiki
Signature
IRC on Freenode : #gentoo-quebec |
|
| Back to top |
|
 |
dmpogo Advocate

Joined: 02 Sep 2004 Posts: 2166 Location: Canada
|
Posted: Thu Oct 01, 2009 4:56 am Post subject: |
|
|
inactive appears also when iwlagn failed to associate with access point. Maybe just because there is none  |
|
| Back to top |
|
 |
pappy_mcfae Watchman


Joined: 27 Dec 2007 Posts: 5807 Location: Pomona, California.
|
|
| Back to top |
|
 |
d2_racing Moderator


Joined: 25 Apr 2005 Posts: 13034 Location: Ste-Foy,Canada
|
Posted: Thu Oct 01, 2009 10:51 am Post subject: |
|
|
Ok Pappy, double check that, because right now, I don't have a clue. _________________ Sysadmin of GentooQuébec.org
Wiki
Signature
IRC on Freenode : #gentoo-quebec |
|
| Back to top |
|
 |
audiodef Advocate


Joined: 06 Jul 2005 Posts: 4952
|
|
| Back to top |
|
 |
pappy_mcfae Watchman


Joined: 27 Dec 2007 Posts: 5807 Location: Pomona, California.
|
|
| Back to top |
|
 |
d2_racing Moderator


Joined: 25 Apr 2005 Posts: 13034 Location: Ste-Foy,Canada
|
Posted: Fri Oct 02, 2009 4:06 am Post subject: |
|
|
I'm testing right now wicd and it's working pretty well.
So, it's not my driver or my card that is dying. It must be a configuration file or a bug inside something that doesn't trigger the wlan0 card. _________________ Sysadmin of GentooQuébec.org
Wiki
Signature
IRC on Freenode : #gentoo-quebec |
|
| Back to top |
|
 |
pappy_mcfae Watchman


Joined: 27 Dec 2007 Posts: 5807 Location: Pomona, California.
|
|
| Back to top |
|
 |
|