Peach
Advocate
Joined: 08 Mar 2003
Posts: 3686
Location: London, UK
|
 Posted: Thu Oct 16, 2008 1:32 pm Post subject: [Kurobox HG] HDD LED blinking with baselayout 2 |
 |
|
Hi all, I've tried to update my kurobox HG to baselayout2 and openrc 0.3.0-r1 and once I rebooted, the HDD led started to blink continuously and it's not stopping.
what's wrong?
did I miss something? Has anyone tried to make this update?
here is my rc.log
| /var/log/rc.log: | * Strarting avr_evtd ...
[ ok ]
* Starting syslog-ng ...
[ ok ]
* Setting clock via the NTP client 'ntpdate' ...
[ ok ]
* Starting portmap ...
[ ok ]
* Mounting network filesystems ...
[ ok ]
* Starting ntpd ...
[ ok ]
* samba -> start: smbd ...
[ ok ]
* samba -> start: nmbd ...
[ ok ]
* Starting sshd ...
[ ok ]
* Starting vixie-cron ...
[ ok ]
* Starting local ...
[ ok ] |
and the full messages output
| /var/log/messages: | Oct 16 08:28:08 kurotree syslog-ng[2315]: syslog-ng starting up; version='2.0.9'
Oct 16 08:28:08 kurotree Using Buffalo Linkstation machine description
Oct 16 08:28:08 kurotree Linux version 2.6.22-gentoo-r5 (root@guro) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.1)) #1 Tue Oct 16 03:22:32 EDT 2007
Oct 16 08:28:08 kurotree Found legacy serial port 0 for /soc10x/serial@80004500
Oct 16 08:28:08 kurotree mem=80004500, taddr=80004500, irq=0, clk=130041000, speed=9600
Oct 16 08:28:08 kurotree Found legacy serial port 1 for /soc10x/serial@80004600
Oct 16 08:28:08 kurotree mem=80004600, taddr=80004600, irq=0, clk=130041000, speed=57600
Oct 16 08:28:08 kurotree Entering add_active_range(0, 0, 32768) 0 entries of 256 used
Oct 16 08:28:08 kurotree Adding PCI host bridge /soc10x/pci@fec00000
Oct 16 08:28:08 kurotree BUFFALO Network Attached Storage Series
Oct 16 08:28:08 kurotree (C) 2002-2005 BUFFALO INC.
Oct 16 08:28:08 kurotree Top of RAM: 0x8000000, Total RAM: 0x8000000
Oct 16 08:28:08 kurotree Memory hole size: 0MB
Oct 16 08:28:08 kurotree Zone PFN ranges:
Oct 16 08:28:08 kurotree DMA 0 -> 32768
Oct 16 08:28:08 kurotree Normal 32768 -> 32768
Oct 16 08:28:08 kurotree early_node_map[1] active PFN ranges
Oct 16 08:28:08 kurotree 0: 0 -> 32768
Oct 16 08:28:08 kurotree On node 0 totalpages: 32768
Oct 16 08:28:08 kurotree DMA zone: 256 pages used for memmap
Oct 16 08:28:08 kurotree DMA zone: 0 pages reserved
Oct 16 08:28:08 kurotree DMA zone: 32512 pages, LIFO batch:7
Oct 16 08:28:08 kurotree Normal zone: 0 pages used for memmap
Oct 16 08:28:08 kurotree Built 1 zonelists. Total pages: 32512
Oct 16 08:28:08 kurotree Kernel command line: root=/dev/sda1 netconsole=6666@192.168.11.150/,@192.168.11.149/ rtc-rs5c372.probe=0,0x32
Oct 16 08:28:08 kurotree netconsole: local port 6666
Oct 16 08:28:08 kurotree netconsole: local IP 192.168.11.150
Oct 16 08:28:08 kurotree netconsole: interface eth0
Oct 16 08:28:08 kurotree netconsole: remote port 6666
Oct 16 08:28:08 kurotree netconsole: remote IP 192.168.11.149
Oct 16 08:28:08 kurotree netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
Oct 16 08:28:08 kurotree mpic: Setting up MPIC " EPIC " version 1.2 at 80040000, max 1 CPUs
Oct 16 08:28:08 kurotree mpic: ISU size: 4, shift: 2, mask: 3
Oct 16 08:28:08 kurotree mpic: Initializing for 12 sources
Oct 16 08:28:08 kurotree PID hash table entries: 512 (order: 9, 2048 bytes)
Oct 16 08:28:08 kurotree time_init: decrementer frequency = 32.522240 MHz
Oct 16 08:28:08 kurotree time_init: processor frequency = 262.144000 MHz
Oct 16 08:28:08 kurotree Console: colour dummy device 80x25
Oct 16 08:28:08 kurotree console handover: boot [udbg0] -> real [tty0]
Oct 16 08:28:08 kurotree Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Oct 16 08:28:08 kurotree Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Oct 16 08:28:08 kurotree Memory: 126420k/131072k available (3064k kernel code, 4488k reserved, 132k data, 106k bss, 148k init)
Oct 16 08:28:08 kurotree Calibrating delay loop... 64.92 BogoMIPS (lpj=324608)
Oct 16 08:28:08 kurotree Mount-cache hash table entries: 512
Oct 16 08:28:08 kurotree NET: Registered protocol family 16
Oct 16 08:28:08 kurotree PCI: Probing PCI hardware
Oct 16 08:28:08 kurotree PCI: Cannot allocate resource region 1 of device 0000:00:00.0
Oct 16 08:28:08 kurotree PCI: Cannot allocate resource region 5 of device 0000:00:0c.0
Oct 16 08:28:08 kurotree SCSI subsystem initialized
Oct 16 08:28:08 kurotree libata version 2.21 loaded.
Oct 16 08:28:08 kurotree usbcore: registered new interface driver usbfs
Oct 16 08:28:08 kurotree usbcore: registered new interface driver hub
Oct 16 08:28:08 kurotree usbcore: registered new device driver usb
Oct 16 08:28:08 kurotree NET: Registered protocol family 2
Oct 16 08:28:08 kurotree IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Oct 16 08:28:08 kurotree TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Oct 16 08:28:08 kurotree TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
Oct 16 08:28:08 kurotree TCP: Hash tables configured (established 4096 bind 4096)
Oct 16 08:28:08 kurotree TCP reno registered
Oct 16 08:28:08 kurotree io scheduler noop registered
Oct 16 08:28:08 kurotree io scheduler anticipatory registered (default)
Oct 16 08:28:08 kurotree io scheduler deadline registered
Oct 16 08:28:08 kurotree io scheduler cfq registered
Oct 16 08:28:08 kurotree Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
Oct 16 08:28:08 kurotree serial8250.0: ttyS0 at MMIO 0x80004500 (irq = 16) is a 16550A
Oct 16 08:28:08 kurotree serial8250.0: ttyS1 at MMIO 0x80004600 (irq = 17) is a 16550A
Oct 16 08:28:08 kurotree RAMDISK driver initialized: 2 RAM disks of 8192K size 1024 blocksize
Oct 16 08:28:08 kurotree loop: module loaded
Oct 16 08:28:08 kurotree r8169 Gigabit Ethernet driver 2.2LK loaded
Oct 16 08:28:08 kurotree eth0: RTL8169s/8110s at 0xc9004c00, 00:0d:0b:99:44:79, IRQ 19
Oct 16 08:28:08 kurotree netconsole: device eth0 not up yet, forcing it
Oct 16 08:28:08 kurotree r8169: eth0: link down
Oct 16 08:28:08 kurotree r8169: eth0: link up
Oct 16 08:28:08 kurotree netconsole: network logging started
Oct 16 08:28:08 kurotree pata_sil680 0000:00:0c.0: version 0.4.6
Oct 16 08:28:08 kurotree sil680: BA5_EN = 1 clock = 00
Oct 16 08:28:08 kurotree sil680: BA5_EN = 1 clock = 10
Oct 16 08:28:08 kurotree sil680: 133MHz clock.
Oct 16 08:28:08 kurotree scsi0 : pata_sil680
Oct 16 08:28:08 kurotree scsi1 : pata_sil680
Oct 16 08:28:08 kurotree ata1: PATA max UDMA/133 cmd 0xfdffbed0 ctl 0xfdffbeda bmdma 0xfdffbef0 irq 20
Oct 16 08:28:08 kurotree ata2: PATA max UDMA/133 cmd 0xfdffbee0 ctl 0xfdffbeea bmdma 0xfdffbef8 irq 20
Oct 16 08:28:08 kurotree ata1.00: ATA-5: ST340016A, 3.19, max UDMA/100
Oct 16 08:28:08 kurotree ata1.00: 78165360 sectors, multi 0: LBA
Oct 16 08:28:08 kurotree ata1.00: configured for UDMA/100
Oct 16 08:28:08 kurotree scsi 0:0:0:0: Direct-Access ATA ST340016A 3.19 PQ: 0 ANSI: 5
Oct 16 08:28:08 kurotree sd 0:0:0:0: [sda] 78165360 512-byte hardware sectors (40021 MB)
Oct 16 08:28:08 kurotree sd 0:0:0:0: [sda] Write Protect is off
Oct 16 08:28:08 kurotree sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Oct 16 08:28:08 kurotree sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 16 08:28:08 kurotree sd 0:0:0:0: [sda] 78165360 512-byte hardware sectors (40021 MB)
Oct 16 08:28:08 kurotree sd 0:0:0:0: [sda] Write Protect is off
Oct 16 08:28:08 kurotree sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Oct 16 08:28:08 kurotree sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 16 08:28:08 kurotree sda: sda1 sda2 sda3
Oct 16 08:28:08 kurotree sd 0:0:0:0: [sda] Attached SCSI disk
Oct 16 08:28:08 kurotree sd 0:0:0:0: Attached scsi generic sg0 type 0
Oct 16 08:28:08 kurotree physmap platform flash device: 00400000 at ffc00000
Oct 16 08:28:08 kurotree physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
Oct 16 08:28:08 kurotree Amd/Fujitsu Extended Query Table at 0x0040
Oct 16 08:28:08 kurotree physmap-flash.0: Swapping erase regions for broken CFI table.
Oct 16 08:28:08 kurotree number of CFI chips: 1
Oct 16 08:28:08 kurotree cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Oct 16 08:28:08 kurotree cmdlinepart partition parsing not available
Oct 16 08:28:08 kurotree RedBoot partition parsing not available
Oct 16 08:28:08 kurotree Using physmap partition information
Oct 16 08:28:08 kurotree Creating 6 MTD partitions on "physmap-flash.0":
Oct 16 08:28:08 kurotree 0x00000000-0x00300000 : "mtd_firmimg"
Oct 16 08:28:08 kurotree 0x00300000-0x00370000 : "mtd_bootcode"
Oct 16 08:28:08 kurotree 0x00370000-0x00380000 : "mtd_status"
Oct 16 08:28:08 kurotree 0x00380000-0x00400000 : "mtd_conf"
Oct 16 08:28:08 kurotree 0x00000000-0x00400000 : "mtd_allflash"
Oct 16 08:28:08 kurotree 0x00310000-0x00400000 : "mtd_data"
Oct 16 08:28:08 kurotree usbmon: debugfs is not available
Oct 16 08:28:08 kurotree ehci_hcd 0000:00:0e.2: EHCI Host Controller
Oct 16 08:28:08 kurotree ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
Oct 16 08:28:08 kurotree ehci_hcd 0000:00:0e.2: irq 21, io mem 0xbfffcf00
Oct 16 08:28:08 kurotree ehci_hcd 0000:00:0e.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
Oct 16 08:28:08 kurotree usb usb1: configuration #1 chosen from 1 choice
Oct 16 08:28:08 kurotree hub 1-0:1.0: USB hub found
Oct 16 08:28:08 kurotree hub 1-0:1.0: 5 ports detected
Oct 16 08:28:08 kurotree ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
Oct 16 08:28:08 kurotree ohci_hcd 0000:00:0e.0: OHCI Host Controller
Oct 16 08:28:08 kurotree ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 2
Oct 16 08:28:08 kurotree ohci_hcd 0000:00:0e.0: irq 21, io mem 0xbfffe000
Oct 16 08:28:08 kurotree usb usb2: configuration #1 chosen from 1 choice
Oct 16 08:28:08 kurotree hub 2-0:1.0: USB hub found
Oct 16 08:28:08 kurotree hub 2-0:1.0: 3 ports detected
Oct 16 08:28:08 kurotree ohci_hcd 0000:00:0e.1: OHCI Host Controller
Oct 16 08:28:08 kurotree ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 3
Oct 16 08:28:08 kurotree ohci_hcd 0000:00:0e.1: irq 21, io mem 0xbfffd000
Oct 16 08:28:08 kurotree usb usb3: configuration #1 chosen from 1 choice
Oct 16 08:28:08 kurotree hub 3-0:1.0: USB hub found
Oct 16 08:28:08 kurotree hub 3-0:1.0: 2 ports detected
Oct 16 08:28:08 kurotree usbcore: registered new interface driver usbserial
Oct 16 08:28:08 kurotree drivers/usb/serial/usb-serial.c: USB Serial Driver core
Oct 16 08:28:08 kurotree drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device
Oct 16 08:28:08 kurotree usbcore: registered new interface driver ftdi_sio
Oct 16 08:28:08 kurotree drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver
Oct 16 08:28:08 kurotree mice: PS/2 mouse device common for all mice
Oct 16 08:28:08 kurotree i2c /dev entries driver
Oct 16 08:28:08 kurotree rtc-rs5c372 0-0032: assuming rs5c372b
Oct 16 08:28:08 kurotree rtc-rs5c372 0-0032: rs5c372b found, 24hr, driver version 0.4
Oct 16 08:28:08 kurotree rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
Oct 16 08:28:08 kurotree TCP cubic registered
Oct 16 08:28:08 kurotree NET: Registered protocol family 1
Oct 16 08:28:08 kurotree NET: Registered protocol family 17
Oct 16 08:28:08 kurotree rtc-rs5c372 0-0032: setting the system clock to 2008-10-16 06:27:39 (1224138459)
Oct 16 08:28:08 kurotree linkstation: disarming the AVR watchdog:
Oct 16 08:28:08 kurotree kjournald starting. Commit interval 5 seconds
Oct 16 08:28:08 kurotree EXT3-fs: mounted filesystem with ordered data mode.
Oct 16 08:28:08 kurotree VFS: Mounted root (ext3 filesystem) readonly.
Oct 16 08:28:08 kurotree Freeing unused kernel memory: 148k init
Oct 16 08:28:08 kurotree EXT3 FS on sda1, internal journal
Oct 16 08:28:08 kurotree kjournald starting. Commit interval 5 seconds
Oct 16 08:28:08 kurotree EXT3 FS on sda3, internal journal
Oct 16 08:28:08 kurotree EXT3-fs: mounted filesystem with ordered data mode.
Oct 16 08:28:08 kurotree Adding 506036k swap on /dev/sda2. Priority:-1 extents:1 across:506036k
Oct 16 13:28:11 kurotree -- MARK --
Oct 16 15:28:12 kurotree ntpdate[2328]: step time server 81.208.58.150 offset 25200.373349 sec
Oct 16 15:28:14 kurotree ntpd[2369]: ntpd 4.2.4p4@1.1520-o mer ott 15 02:30:05 UTC 2008 (1)
Oct 16 15:28:14 kurotree ntpd[2370]: precision = 1.000 usec
Oct 16 15:28:14 kurotree ntpd[2370]: Listening on interface #0 wildcard, 0.0.0.0#123 Disabled
Oct 16 15:28:14 kurotree ntpd[2370]: Listening on interface #1 lo, 127.0.0.1#123 Enabled
Oct 16 15:28:14 kurotree ntpd[2370]: Listening on interface #2 eth0, 192.168.123.147#123 Enabled
Oct 16 15:28:14 kurotree ntpd[2370]: kernel time sync status 0040
Oct 16 15:28:14 kurotree ntpd[2370]: frequency initialized 20.578 PPM from /var/lib/ntp/ntp.drift |
imho, there's nothing wrong, apart from the blinking light... pls enlighten me ! 
[edit] tried to downgrade openrc to 0.2.5 but nothing changed
_________________
Gentoo user since 2004.
"It's all fun and games, until someone loses an eye" - mom |
|
Gentoo on Alternative Architectures
