Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
české forum
View unanswered posts
View posts from last 24 hours

Goto page Previous  1, 2, 3, 4, 5, 6, 7  Next  
Reply to topic    Gentoo Forums Forum Index Other Languages
View previous topic :: View next topic  
Author Message
cz_mara
n00b
n00b


Joined: 19 Dec 2005
Posts: 16

PostPosted: Thu Dec 29, 2005 7:13 pm    Post subject: Reply with quote

jadro: linux-2.6.14-gentoo-r2
nvidia-kernel: 1.0.6629-r4
dmesg:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000017ff0000 (usable)
BIOS-e820: 0000000017ff0000 - 0000000017ff3000 (ACPI NVS)
BIOS-e820: 0000000017ff3000 - 0000000018000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
383MB LOWMEM available.
On node 0 totalpages: 98288
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 94192 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 AWARD ) @ 0x000f7a30
ACPI: RSDT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x17ff3000
ACPI: FADT (v001 AWARD AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x17ff3040
ACPI: DSDT (v001 AWARD AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 20000000 (gap: 18000000:e7ff0000)
Built 1 zonelists
Kernel command line: root=/dev/ram0 init=linuxrc ramdisk=8192 real_root=/dev/hdb3 udev
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01342000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 900.139 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 382776k/393152k available (3044k kernel code, 9824k reserved, 853k data, 236k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1802.36 BogoMIPS (lpj=3604724)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000020 00000000 00000000 00000000
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0800 (from 0e20)
CPU0: AMD Duron(tm) processor stepping 01
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
checking if image is initramfs...softlockup thread 0 started up.
it is
Freeing initrd memory: 1658k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb350, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region 6000-607f claimed by vt82c868 HW-mon
PCI quirk: region 5000-500f claimed by vt82c868 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: ACPI device : hid PNP0C01
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0400
pnp: ACPI device : hid PNP0F13
pnp: ACPI device : hid PNP0303
pnp: PnP ACPI: found 12 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:00' and the driver 'system'
pnp: match found with the PnP device '00:01' and the driver 'system'
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: dc000000-ddffffff
PREFETCH window: d0000000-d7ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
Applying VIA southbridge workaround.
PCI: Disabling Via external APIC routing
vesafb: NVidia Corporation, NV15 Board, Chip Rev A0 (OEM: NVidia)
vesafb: VBE version: 3.0
vesafb: VBIOS/hardware supports DDC2 transfers
vesafb: no monitor limits have been set
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 80x30
vesafb: framebuffer at 0xd0000000, mapped to 0xd8880000, using 7500k, total 65536k
fb0: VESA VGA frame buffer device
pnp: the driver 'i8042 kbd' has been registered
pnp: match found with the PnP device '00:0b' and the driver 'i8042 kbd'
pnp: the driver 'i8042 aux' has been registered
pnp: match found with the PnP device '00:0a' and the driver 'i8042 aux'
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pnp: the driver 'serial' has been registered
pnp: match found with the PnP device '00:07' and the driver 'serial'
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
pnp: match found with the PnP device '00:08' and the driver 'serial'
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport_pc: VIA parallel port: io=0x378, irq=7
mice: PS/2 mouse device common for all mice
io scheduler noop registered
io scheduler deadline registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
v2.3 : Micro Memory(tm) PCI memory board block driver
MM: desc_per_page = 128
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
PCI: Via IRQ fixup for 0000:00:07.1, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard on isa0060/serio0
input: GenPS/2 Genius Wheel Mouse on isa0060/serio1
hda: WDC WD800JB-00FMA0, ATA DISK drive
hdb: ST310215A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SONY CD-ROM CDU5221, ATAPI CD/DVD-ROM drive
hdd: LITE-ON LTR-52327S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
pnp: the driver 'ide' has been registered
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1
hdb: max request size: 128KiB
hdb: 19541088 sectors (10005 MB) w/2048KiB Cache, CHS=19386/16/63, UDMA(100)
hdb: cache flushes not supported
hdb: hdb1 hdb2 hdb3
hdc: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
Cannot allocate resource for EISA slot 6
EISA: Detected 0 cards.
Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12 08:13:09 2005 UTC).
ALSA device list:
No soundcards found.
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Freeing unused kernel memory: 236k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.2[C] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:0a.2: EHCI Host Controller
ehci_hcd 0000:00:0a.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.2: irq 11, io mem 0xdf001000
ehci_hcd 0000:00:0a.2: USB 2.0 initialized, EHCI 0.95, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
usb 1-3: new high speed USB device using ehci_hcd and address 3
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:07.2: irq 11, io base 0x0000c400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:07.3: irq 11, io base 0x0000c800
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: Via IRQ fixup for 0000:00:0a.0, from 9 to 10
uhci_hcd 0000:00:0a.0: UHCI Host Controller
uhci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:0a.0: irq 10, io base 0x0000dc00
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.1[B] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:0a.1: UHCI Host Controller
uhci_hcd 0000:00:0a.1: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:0a.1: irq 5, io base 0x0000e000
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
sl811: driver sl811-hcd, 19 May 2005
ieee1394: Initialized config rom entry `ip1394'
sbp2: $Rev: 1306 $ Ben Collins <bcollins@debian.org>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
usb 4-2: new full speed USB device using uhci_hcd and address 2
libata version 1.12 loaded.
ReiserFS: hdb3: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on hdb3
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Vendor: ST316002 Model: 3A Rev: 0 0
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: assuming drive cache: write through
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: assuming drive cache: write through
sda: sda1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
usb-storage: device scan complete
Adding 787176k swap on /dev/hdb2. Priority:-1 extents:1 across:787176k
EXT3 FS on hdb3, internal journal
Linux agpgart interface v0.101 (c) Dave Jones
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-6629 Wed Nov 3 13:12:51 PST 2004
agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
agpgart: AGP aperture is 64M @ 0xd8000000
ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:07.5 to 64
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:00:0c.0: 3Com PCI 3c905B Cyclone 100baseTx at 0xe400. Vers LK1.1.19
Real Time Clock Driver v1.12
input: PC Speaker
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0487ac0(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdb: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
Back to top
View user's profile Send private message
cz_mara
n00b
n00b


Joined: 19 Dec 2005
Posts: 16

PostPosted: Thu Dec 29, 2005 7:15 pm    Post subject: Reply with quote

jo jinak pouzivam genkernel -ale to je asi tak tyden - zkousel sel sem to kvuli to nVidii
Back to top
View user's profile Send private message
cz_mara
n00b
n00b


Joined: 19 Dec 2005
Posts: 16

PostPosted: Thu Dec 29, 2005 8:21 pm    Post subject: Reply with quote

jeste Xorg log

X Window System Version 6.8.2
Release Date: 9 February 2005
X Protocol Version 11, Revision 0, Release 6.8.2
Build Operating System: Linux 2.6.13-gentoo-r3 i686 [ELF]
Current Operating System: Linux oplmlewandowski 2.6.14-gentoo-r2 #2 Wed Dec 7 19:37:46 CET 2005 i686
Build Date: 25 November 2005
Before reporting problems, check http://wiki.X.Org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Dec 19 22:09:57 2005
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Geforce2 Ti"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(WW) The directory "/usr/share/fonts/CID/" does not exist.
Entry deleted from font path.
(**) FontPath set to "/usr/share/fonts/misc/,/usr/share/fonts/TTF/,/usr/share/fonts/Type1/,/usr/share/fonts/75dpi/,/usr/share/fonts/100dpi/"
(**) RgbPath set to "/usr/lib/X11/rgb"
(**) ModulePath set to "/usr/lib/modules"
(WW) Open APM failed (/dev/apm_bios) (No such file or directory)
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.2
X.Org Video Driver: 0.7
X.Org XInput driver : 0.4
X.Org Server Extension : 0.2
X.Org Font Renderer : 0.4
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/lib/modules/libpcidata.a
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.7
Using vt 7
(--) using VT number 7

(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1106,0305 card 0000,0000 rev 03 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 1106,8305 card 0000,0000 rev 00 class 06,04,00 hdr 01
(II) PCI: 00:07:0: chip 1106,0686 card 1106,0000 rev 40 class 06,01,00 hdr 80
(II) PCI: 00:07:1: chip 1106,0571 card 1106,0571 rev 06 class 01,01,8a hdr 00
(II) PCI: 00:07:2: chip 1106,3038 card 0925,1234 rev 1a class 0c,03,00 hdr 00
(II) PCI: 00:07:3: chip 1106,3038 card 0925,1234 rev 1a class 0c,03,00 hdr 00
(II) PCI: 00:07:4: chip 1106,3057 card 0000,0000 rev 40 class 06,80,00 hdr 00
(II) PCI: 00:07:5: chip 1106,3058 card 11d4,5348 rev 50 class 04,01,00 hdr 00
(II) PCI: 00:0a:0: chip 1106,3038 card 0925,1234 rev 50 class 0c,03,00 hdr 80
(II) PCI: 00:0a:1: chip 1106,3038 card 0925,1234 rev 50 class 0c,03,00 hdr 80
(II) PCI: 00:0a:2: chip 1106,3104 card 0925,1234 rev 51 class 0c,03,20 hdr 80
(II) PCI: 00:0c:0: chip 10b7,9055 card 10b7,9055 rev 30 class 02,00,00 hdr 00
(II) PCI: 01:00:0: chip 10de,0151 card 1462,3601 rev a4 class 03,00,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x000c (VGA_EN is set)
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xdc000000 - 0xddffffff (0x2000000) MX[B]
(II) Bus 1 prefetchable memory range:
[0] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[B]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:7:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(--) PCI:*(1:0:0) nVidia Corporation NV15DDR [GeForce2 Ti] rev 164, Mem @ 0xdc000000/24, 0xd0000000/27
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) PCI Memory resource overlap reduced 0xd8000000 from 0xdbffffff to 0xd7ffffff
(II) Active PCI resource ranges:
[0] -1 0 0xdf000000 - 0xdf00007f (0x80) MX[B]
[1] -1 0 0xdf001000 - 0xdf0010ff (0x100) MX[B]
[2] -1 0 0xd8000000 - 0xd7ffffff (0x0) MX[B]O
[3] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
[4] -1 0 0xdc000000 - 0xdcffffff (0x1000000) MX[B](B)
[5] -1 0 0x0000e400 - 0x0000e47f (0x80) IX[B]
[6] -1 0 0x0000e000 - 0x0000e01f (0x20) IX[B]
[7] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[8] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B]
[9] -1 0 0x0000d000 - 0x0000d003 (0x4) IX[B]
[10] -1 0 0x0000cc00 - 0x0000ccff (0x100) IX[B]
[11] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B]
[12] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B]
[13] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B]
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xdf000000 - 0xdf00007f (0x80) MX[B]
[1] -1 0 0xdf001000 - 0xdf0010ff (0x100) MX[B]
[2] -1 0 0xd8000000 - 0xd7ffffff (0x0) MX[B]O
[3] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
[4] -1 0 0xdc000000 - 0xdcffffff (0x1000000) MX[B](B)
[5] -1 0 0x0000e400 - 0x0000e47f (0x80) IX[B]
[6] -1 0 0x0000e000 - 0x0000e01f (0x20) IX[B]
[7] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[8] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B]
[9] -1 0 0x0000d000 - 0x0000d003 (0x4) IX[B]
[10] -1 0 0x0000cc00 - 0x0000ccff (0x100) IX[B]
[11] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B]
[12] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B]
[13] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xdf000000 - 0xdf00007f (0x80) MX[B]
[6] -1 0 0xdf001000 - 0xdf0010ff (0x100) MX[B]
[7] -1 0 0xd8000000 - 0xd7ffffff (0x0) MX[B]O
[8] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
[9] -1 0 0xdc000000 - 0xdcffffff (0x1000000) MX[B](B)
[10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[11] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[12] -1 0 0x0000e400 - 0x0000e47f (0x80) IX[B]
[13] -1 0 0x0000e000 - 0x0000e01f (0x20) IX[B]
[14] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[15] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B]
[16] -1 0 0x0000d000 - 0x0000d003 (0x4) IX[B]
[17] -1 0 0x0000cc00 - 0x0000ccff (0x100) IX[B]
[18] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B]
[19] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B]
[20] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B]
(II) LoadModule: "glx"
(II) Loading /usr/lib/modules/extensions/libglx.so
(II) Module glx: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.6629
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version 0.1
(II) Loading extension GLX
(II) LoadModule: "dbe"
(II) Loading /usr/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "xtrap"
(II) Loading /usr/lib/modules/extensions/libxtrap.a
(II) Module xtrap: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension DEC-XTRAP
(II) LoadModule: "nvidia"
(II) Loading /usr/lib/modules/drivers/nvidia_drv.o
(II) Module nvidia: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.6629
Module class: XFree86 Video Driver
(II) LoadModule: "mouse"
(II) Loading /usr/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.4
(II) LoadModule: "kbd"
(II) Loading /usr/lib/modules/input/kbd_drv.o
(II) Module kbd: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.4
(II) NVIDIA X Driver 1.0-6629 Wed Nov 3 13:14:07 PST 2004
(II) NVIDIA Unified Driver for all NVIDIA GPUs
(II) Primary Device is: PCI 01:00:0
(--) Chipset NVIDIA GPU found
(II) Found 1 PCI NVIDIA devices
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xdf000000 - 0xdf00007f (0x80) MX[B]
[6] -1 0 0xdf001000 - 0xdf0010ff (0x100) MX[B]
[7] -1 0 0xd8000000 - 0xd7ffffff (0x0) MX[B]O
[8] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
[9] -1 0 0xdc000000 - 0xdcffffff (0x1000000) MX[B](B)
[10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[11] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[12] -1 0 0x0000e400 - 0x0000e47f (0x80) IX[B]
[13] -1 0 0x0000e000 - 0x0000e01f (0x20) IX[B]
[14] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[15] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B]
[16] -1 0 0x0000d000 - 0x0000d003 (0x4) IX[B]
[17] -1 0 0x0000cc00 - 0x0000ccff (0x100) IX[B]
[18] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B]
[19] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B]
[20] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B]
(II) resource ranges after probing:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xdf000000 - 0xdf00007f (0x80) MX[B]
[6] -1 0 0xdf001000 - 0xdf0010ff (0x100) MX[B]
[7] -1 0 0xd8000000 - 0xd7ffffff (0x0) MX[B]O
[8] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
[9] -1 0 0xdc000000 - 0xdcffffff (0x1000000) MX[B](B)
[10] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[11] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[12] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[13] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[14] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[15] -1 0 0x0000e400 - 0x0000e47f (0x80) IX[B]
[16] -1 0 0x0000e000 - 0x0000e01f (0x20) IX[B]
[17] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[18] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B]
[19] -1 0 0x0000d000 - 0x0000d003 (0x4) IX[B]
[20] -1 0 0x0000cc00 - 0x0000ccff (0x100) IX[B]
[21] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B]
[22] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B]
[23] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B]
[24] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[25] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(**) NVIDIA(0): Depth 16, (--) framebuffer bpp 16
(==) NVIDIA(0): RGB weight 565
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(==) NVIDIA(0): Using HW cursor
(==) NVIDIA(0): Video key set to default value of 0x83e
(--) NVIDIA(0): Linear framebuffer at 0xD0000000
(--) NVIDIA(0): MMIO registers at 0xDC000000
(EE) NVIDIA(0): Failed to initialize the NVIDIA kernel module!
(EE) NVIDIA(0): *** Aborting ***
(II) UnloadModule: "nvidia"
(EE) Screen(s) found, but none have a usable configuration.

Fatal server error:
no screens found

Please consult the The X.Org Foundation support
at http://wiki.X.Org
for help.
Please also check the log file at "/var/log/Xorg.0.log" for additional information.

(II) Setting vga for screen 0.
(**) NVIDIA(0): Depth 16, (--) framebuffer bpp 16
(==) NVIDIA(0): RGB weight 565
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(==) NVIDIA(0): Using HW cursor
(==) NVIDIA(0): Video key set to default value of 0x83e
(--) NVIDIA(0): Linear framebuffer at 0xD0000000
(--) NVIDIA(0): MMIO registers at 0xDC000000
(EE) NVIDIA(0): Failed to initialize the NVIDIA kernel module!
(EE) NVIDIA(0): *** Aborting ***
(II) UnloadModule: "nvidia"
(EE) Screen(s) found, but none have a usable configuration.
Back to top
View user's profile Send private message
dekon
Tux's lil' helper
Tux's lil' helper


Joined: 21 Aug 2005
Posts: 80

PostPosted: Fri Dec 30, 2005 1:00 pm    Post subject: Reply with quote

Sakra, ty ses teda post hunter :roll:
To si nemohl dat vsechno do jednoho prispevku ?

Priste k vkladani kodu pouzij tag code lip se to cte ....
Vsim jsem si ze to to hlasi nejake potize s prerusenim, to me delalo taky, pak jsem nemoch pouzit ovladac od nvidia a nesel mi ani zvuk.
Zkus pri bootovani jadru predat parametr acpi=off nebo mozna noacpi.
Jestli mas LILO staci, kdyz vyberes obraz jadra kterej chces bootovat das mezernik a za to napises acpi=off.
Jak to ma GRUB nevim, v zivote jsem ho nepouzival ....

poripade posli jeste vypis
Code:
ls -l /dev/nvidia*

at vime jestli se ti vubec vytvorili soubory zarizeni nutne k akceleraci (u nekterych jader problem).
U me vypis vypada tahle:
ls -l /dev/nvidia*
Code:

crw-rw-rw-  1 root root 195,   0 Dec 26 14:57 /dev/nvidia0
crw-rw-rw-  1 root root 195, 255 Dec 26 14:57 /dev/nvidiactl

EDIT: To tvoje jadro je docela novy, nevim jestli je nejlepsi napad tam cpat nvidia-kernel 1.0.6629-r4, zkus pouzit ovladace oznacene ~x86.

Jinak kdyby zadnej s tech tipu co jsem tu poslal nepomoch, prohledej forum, je tady toho o nvidia dost, urcite najdes reseni.
_________________
Sorry for my English,i am not good at in this :)


Last edited by dekon on Fri Dec 30, 2005 1:10 pm; edited 1 time in total
Back to top
View user's profile Send private message
cz_mara
n00b
n00b


Joined: 19 Dec 2005
Posts: 16

PostPosted: Fri Dec 30, 2005 1:10 pm    Post subject: Reply with quote

takze zarizeni tam je sice nevim proc tolik ale je tam
no mam zrovna grub ale nejak to zkusim spachat ale ted na to nemam cas...az podvecer

Code:
crw-rw-rw-  1 root root 195,   0 Dec 28 21:03 /dev/nvidia0
crw-rw-rw-  1 root root 195,   1 Dec 28 21:03 /dev/nvidia1
crw-rw-rw-  1 root root 195,   2 Dec 28 21:03 /dev/nvidia2
crw-rw-rw-  1 root root 195,   3 Dec 28 21:03 /dev/nvidia3
crw-rw-rw-  1 root root 195,   4 Dec 28 21:03 /dev/nvidia4
crw-rw-rw-  1 root root 195,   5 Dec 28 21:03 /dev/nvidia5
crw-rw-rw-  1 root root 195,   6 Dec 28 21:03 /dev/nvidia6
crw-rw-rw-  1 root root 195,   7 Dec 28 21:03 /dev/nvidia7
crw-rw-rw-  1 root root 195, 255 Dec 28 21:03 /dev/nvidiactl
Back to top
View user's profile Send private message
dekon
Tux's lil' helper
Tux's lil' helper


Joined: 21 Aug 2005
Posts: 80

PostPosted: Fri Dec 30, 2005 1:14 pm    Post subject: Reply with quote

Popripade se zkus podivat sem :arrow: http://forums.gentoo.org/viewtopic-t-394817.html
_________________
Sorry for my English,i am not good at in this :)
Back to top
View user's profile Send private message
cz_mara
n00b
n00b


Joined: 19 Dec 2005
Posts: 16

PostPosted: Fri Dec 30, 2005 1:20 pm    Post subject: Reply with quote

stim ovladacem sem to moc nepochopil....co mam presne udelat
Back to top
View user's profile Send private message
dekon
Tux's lil' helper
Tux's lil' helper


Joined: 21 Aug 2005
Posts: 80

PostPosted: Fri Dec 30, 2005 1:27 pm    Post subject: Reply with quote

do /etc/portage/package.keywords:
Code:

=media-video/nvidia-kernel-1.0.7676 ~x86
=media-video/nvidia-glx-1.0.7676-r1 ~x86

Tim budes mit povolenou instalaci "testovacich" nvidia ovladacu.
Vrele doporucuju projit ten odkaz co jsem ti daval vyse, ten by mel pomoct.
_________________
Sorry for my English,i am not good at in this :)
Back to top
View user's profile Send private message
cz_mara
n00b
n00b


Joined: 19 Dec 2005
Posts: 16

PostPosted: Fri Dec 30, 2005 6:26 pm    Post subject: Reply with quote

kdyz pouziju tyto ovladace
Code:
nvidia-kernel-1.0.7676
nvidia-glx-1.0.7676-r1

tak me modprobe nvidia rekne
Code:
FATAL: Error inserting nvidia (/lib/modules/2.6.14-gentoo-r5/video/nvidia.ko): No such device

:?
Back to top
View user's profile Send private message
cz_mara
n00b
n00b


Joined: 19 Dec 2005
Posts: 16

PostPosted: Fri Dec 30, 2005 7:38 pm    Post subject: Reply with quote

jo tak to bylo jen jadrem ktery sem se pokusil aktualizovat.
a mam novou hlasku u tech novejsich ovladacu
Code:

(II) NVIDIA X Driver  1.0-7676  Fri Jul 29 13:01:02 PDT 2005
(II) NVIDIA Unified Driver for all NVIDIA GPUs
(II) Primary Device is: PCI 01:00:0
(WW) The NVIDIA GeForce2 Ti GPU installed in this system is
(WW)      supported through the NVIDIA Legacy drivers. Please visit
(WW)      http://www.nvidia.com/object/unix.html for more
(WW)      information.  The 1.0-7676 NVIDIA driver will ignore this
(WW)      GPU.  Continuing probe...
(EE) No devices detected
Back to top
View user's profile Send private message
dekon
Tux's lil' helper
Tux's lil' helper


Joined: 21 Aug 2005
Posts: 80

PostPosted: Fri Dec 30, 2005 8:43 pm    Post subject: Reply with quote

Tahle tvoje nova hlaska rika, ze ovladac 7676 uz nepodporuje Ge Force 2 Ti a ze tenhle chip bude dal podporovan nejakym legacy driverem.
_________________
Sorry for my English,i am not good at in this :)
Back to top
View user's profile Send private message
cz_mara
n00b
n00b


Joined: 19 Dec 2005
Posts: 16

PostPosted: Fri Dec 30, 2005 8:46 pm    Post subject: Reply with quote

no nejak tak sem si to taky vylozil.... :)
a tak sem pokracoval starsi radou ovlacu najednou buch a zniceho nic se to rozjelo
az tomu sam neverim
takze problem je vyresen uzavren
takze diky vsem za rady....
Back to top
View user's profile Send private message
dekon
Tux's lil' helper
Tux's lil' helper


Joined: 21 Aug 2005
Posts: 80

PostPosted: Fri Dec 30, 2005 8:53 pm    Post subject: Reply with quote

Jaka verze ovladacu ti nakonec pomohla ?
_________________
Sorry for my English,i am not good at in this :)
Back to top
View user's profile Send private message
cz_mara
n00b
n00b


Joined: 19 Dec 2005
Posts: 16

PostPosted: Fri Dec 30, 2005 9:00 pm    Post subject: Reply with quote

nakonec se to povedlo 7174 a s mensim figlem s toho odkazu co je o kousek vis.
takze pohoda - ted se pokusim zbavit genkernelu jen se me nejak rozjely zvuky ktere pred tim nefungovaly
Back to top
View user's profile Send private message
Joudy
n00b
n00b


Joined: 30 Dec 2005
Posts: 3
Location: Czech Republic

PostPosted: Sun Jan 01, 2006 4:03 pm    Post subject: Reply with quote

Hlásím dal¹ího spokojeného èeského u¾ivatele Gentoo. U¾ si s Linuxem hraju nìjakou dobu, ale teï jsem si dal oficiální pøedsevzetí ¾e zùstanu a jak na Nový rok, tak po celý rok :)
Back to top
View user's profile Send private message
cz_mara
n00b
n00b


Joined: 19 Dec 2005
Posts: 16

PostPosted: Mon Jan 09, 2006 8:39 pm    Post subject: Reply with quote

Cau lidi! tak nVidia uz slape ale nektere aplikace nejdou proste naistalovat napr. Wormux hlasi
Code:

checking for IceConnectionNumber in -lICE... yes
checking for XOpenDisplay in -lX11... yes
checking for pkg-config... /usr/bin/pkg-config
checking for libxml++... yes
checking for clanGL-0.7... no
configure: error: *** ClanLib GL module version 0.7 not found!

!!! ERROR: games-strategy/wormux-0.5.1 failed.
!!! Function egamesconf, Line 64, Exitcode 1

no a to jsem clanlib zkousel preinstalovat ale ClanLib GL se nechce naistalovat nevim proc
Code:

Calculating dependencies ...done! >>> emerge (1 of 1) dev-games/clanlib-0.7.8-r1 to /
>>> md5 files   ;-) clanlib-0.6.5-r3.ebuild
>>> md5 files   ;-) clanlib-0.7.8-r1.ebuild
>>> md5 files   ;-) files/clanlib-0.6.5-DirectFB-update.patch
>>> md5 files   ;-) files/0.7.8-install-opengl-wrap.patch
>>> md5 files   ;-) files/0.7.8-port.patch
>>> md5 files   ;-) files/clanlib-0.6.5-freetype.patch
>>> md5 files   ;-) files/clanlib-0.6.5-gcc3.patch
>>> md5 files   ;-) files/digest-clanlib-0.6.5-r3
>>> md5 files   ;-) files/digest-clanlib-0.7.8-r1
>>> md5 src_uri ;-) ClanLib-0.7.8-1.tar.bz2
>>> Unpacking source...
>>> Unpacking ClanLib-0.7.8-1.tar.bz2 to /var/tmp/portage/clanlib-0.7.8-r1/work
 * Applying 0.7.8-port.patch ...                                                                                                              [ ok ] * Applying 0.7.8-install-opengl-wrap.patch ...                                                                                               [ ok ]>>> Source unpacked.
 * econf: updating ClanLib-0.7.8/config.guess with /usr/share/gnuconfig/config.guess
 * econf: updating ClanLib-0.7.8/config.sub with /usr/share/gnuconfig/config.sub
./configure --prefix=/usr --host=i686-pc-linux-gnu --mandir=/usr/share/man --infodir=/usr/share/info --datadir=/usr/share --sysconfdir=/etc --localstatedir=/var/lib --enable-dyn --enable-clanNetwork --disable-dependency-tracking --enable-asm386 --disable-docs --disable-clanVoice --disable-clanJavaScript --enable-clanGL --enable-clanSDL --enable-clanVorbis --enable-clanMikMod --enable-getaddr --build=i686-pc-linux-gnu
checking build system type... i686-pc-linux-gnu
checking host system type... i686-pc-linux-gnu
checking target system type... i686-pc-linux-gnu
checking for a BSD-compatible install... /bin/install -c
checking whether build environment is sane... yes
checking for gawk... gawk
checking whether make sets $(MAKE)... yes
checking for i686-pc-linux-gnu-g++... i686-pc-linux-gnu-g++
checking for C++ compiler default output file name... a.out
checking whether the C++ compiler works... yes
checking whether we are cross compiling... no
checking for suffix of executables...
checking for suffix of object files... o
checking whether we are using the GNU C++ compiler... yes
checking whether i686-pc-linux-gnu-g++ accepts -g... yes
checking for style of include used by make... GNU
checking dependency style of i686-pc-linux-gnu-g++... none
checking for i686-pc-linux-gnu-gcc... i686-pc-linux-gnu-gcc
checking whether we are using the GNU C compiler... yes
checking whether i686-pc-linux-gnu-gcc accepts -g... yes
checking for i686-pc-linux-gnu-gcc option to accept ANSI C... none needed
checking dependency style of i686-pc-linux-gnu-gcc... none
checking how to run the C preprocessor... i686-pc-linux-gnu-gcc -E
checking for a BSD-compatible install... /bin/install -c
checking for a sed that does not truncate output... /bin/sed
checking for egrep... grep -E
checking for ld used by i686-pc-linux-gnu-gcc... /usr/i686-pc-linux-gnu/bin/ld
checking if the linker (/usr/i686-pc-linux-gnu/bin/ld) is GNU ld... yes
checking for /usr/i686-pc-linux-gnu/bin/ld option to reload object files... -r
checking for BSD-compatible nm... /usr/bin/i686-pc-linux-gnu-nm -B
checking whether ln -s works... yes
checking how to recognise dependent libraries... pass_all
checking for ANSI C header files... yes
checking for sys/types.h... yes
checking for sys/stat.h... yes
checking for stdlib.h... yes
checking for string.h... yes
checking for memory.h... yes
checking for strings.h... yes
checking for inttypes.h... yes
checking for stdint.h... yes
checking for unistd.h... yes
checking dlfcn.h usability... yes
checking dlfcn.h presence... yes
checking for dlfcn.h... yes
checking how to run the C++ preprocessor... i686-pc-linux-gnu-g++ -E
checking for i686-pc-linux-gnu-g77... i686-pc-linux-gnu-g77
checking whether we are using the GNU Fortran 77 compiler... yes
checking whether i686-pc-linux-gnu-g77 accepts -g... yes
checking the maximum length of command line arguments... 32768
checking command to parse /usr/bin/i686-pc-linux-gnu-nm -B output from i686-pc-linux-gnu-gcc object... ok
checking for objdir... .libs
checking for i686-pc-linux-gnu-ar... i686-pc-linux-gnu-ar
checking for i686-pc-linux-gnu-ranlib... i686-pc-linux-gnu-ranlib
checking for i686-pc-linux-gnu-strip... i686-pc-linux-gnu-strip
checking if i686-pc-linux-gnu-gcc static flag  works... yes
checking if i686-pc-linux-gnu-gcc supports -fno-rtti -fno-exceptions... no
checking for i686-pc-linux-gnu-gcc option to produce PIC... -fPIC
checking if i686-pc-linux-gnu-gcc PIC flag -fPIC works... yes
checking if i686-pc-linux-gnu-gcc supports -c -o file.o... yes
checking whether the i686-pc-linux-gnu-gcc linker (/usr/i686-pc-linux-gnu/bin/ld) supports shared libraries... yes
checking whether -lc should be explicitly linked in... no
checking dynamic linker characteristics... GNU/Linux ld.so
checking how to hardcode library paths into programs... immediate
checking whether stripping libraries is possible... yes
checking if libtool supports shared libraries... yes
checking whether to build shared libraries... yes
checking whether to build static libraries... yes
configure: creating libtool
appending configuration tag "CXX" to libtool
checking for ld used by i686-pc-linux-gnu-g++... /usr/i686-pc-linux-gnu/bin/ld
checking if the linker (/usr/i686-pc-linux-gnu/bin/ld) is GNU ld... yes
checking whether the i686-pc-linux-gnu-g++ linker (/usr/i686-pc-linux-gnu/bin/ld) supports shared libraries... yes
checking for i686-pc-linux-gnu-g++ option to produce PIC... -fPIC
checking if i686-pc-linux-gnu-g++ PIC flag -fPIC works... yes
checking if i686-pc-linux-gnu-g++ supports -c -o file.o... yes
checking whether the i686-pc-linux-gnu-g++ linker (/usr/i686-pc-linux-gnu/bin/ld) supports shared libraries... yes
checking dynamic linker characteristics... GNU/Linux ld.so
checking how to hardcode library paths into programs... immediate
checking whether stripping libraries is possible... yes
appending configuration tag "F77" to libtool
checking if libtool supports shared libraries... yes
checking whether to build shared libraries... yes
checking whether to build static libraries... yes
checking for i686-pc-linux-gnu-g77 option to produce PIC... -fPIC
checking if i686-pc-linux-gnu-g77 PIC flag -fPIC works... yes
checking if i686-pc-linux-gnu-g77 supports -c -o file.o... yes
checking whether the i686-pc-linux-gnu-g77 linker (/usr/i686-pc-linux-gnu/bin/ld) supports shared libraries... yes
checking dynamic linker characteristics... GNU/Linux ld.so
checking how to hardcode library paths into programs... immediate
checking whether stripping libraries is possible... yes
checking for pkg-config... /usr/bin/pkg-config
checking for unistd.h... (cached) yes
checking fcntl.h usability... yes
checking fcntl.h presence... yes
checking for fcntl.h... yes
checking sys/kd.h usability... yes
checking sys/kd.h presence... yes
checking for sys/kd.h... yes
checking sys/vt.h usability... yes
checking sys/vt.h presence... yes
checking for sys/vt.h... yes
checking for i386... yes
checking for i386 assembly support... enabled
checking for dynamic loading support... enabled
checking libgen.h usability... yes
checking libgen.h presence... yes
checking for libgen.h... yes
checking for sys/types.h... (cached) yes
checking sys/ipc.h usability... yes
checking sys/ipc.h presence... yes
checking for sys/ipc.h... yes
checking sys/shm.h usability... yes
checking sys/shm.h presence... yes
checking for sys/shm.h... yes
checking fstab.h usability... yes
checking fstab.h presence... yes
checking for fstab.h... yes
checking for pthread_create in -lpthread... yes
checking for main in -lz... yes

Checking for ClanLib Modules to build...
========================================
checking whether we should try to build documentation... no
checking whether we should try to build clanDisplay... yes
checking whether we should try to build clanSDL... yes
checking whether we should try to build clanGL... yes
checking whether we should try to build clanSound... yes
checking whether we should try to build clanNetwork... yes
checking whether we should try to build clanGUI... yes
checking whether we should try to build clanMikMod... yes
checking whether we should try to build clanVorbis... yes

Checking for clanDisplay stuff
==============================
checking for X... libraries , headers
checking for gethostbyname... yes
checking for connect... yes
checking for remove... yes
checking for shmat... yes
checking for IceConnectionNumber in -lICE... yes
checking for png... yes
checking for jpeg... yes
checking for main in -lXxf86vm_pic... no
checking for main in -lXxf86vm... yes
checking for sdl-config... /usr/bin/sdl-config
checking for SDL - version >= 1.2.0... yes
checking for zoomSurface in -lSDL_gfx... yes
checking for GL... no
checking for glXGetProcAddressARB in -lGL... no

Checking for clanSound stuff
============================
checking for mikmod... yes
checking for vorbis... yes

Checking for clanNetwork stuff
==============================
checking for getaddrinfo... yes
checking for GetAddr (ipv6) support... enabled


Checking for debugging and profiling
====================================
checking for debug mode... disabled
checking for profile mode... disabled

checking for maintainer mode... disabled
configure: creating ./config.status
config.status: creating pkgconfig/clanApp.pc
config.status: creating pkgconfig/clanCore.pc
config.status: creating pkgconfig/clanDisplay.pc
config.status: creating pkgconfig/clanGL.pc
config.status: creating pkgconfig/clanSDL.pc
config.status: creating pkgconfig/clanGUI.pc
config.status: creating pkgconfig/clanGUIStyleSilver.pc
config.status: creating pkgconfig/clanMikMod.pc
config.status: creating pkgconfig/clanNetwork.pc
config.status: creating pkgconfig/clanSignals.pc
config.status: creating pkgconfig/clanSound.pc
config.status: creating pkgconfig/clanVorbis.pc
config.status: creating pkgconfig/Makefile
config.status: creating Makefile
config.status: creating Documentation/Makefile
config.status: creating Documentation/Overview/Makefile
config.status: creating Documentation/Reference/Makefile
config.status: creating Documentation/Reference/pce2
config.status: creating Documentation/Tutorial/Makefile
config.status: creating Documentation/Utilities/webbuilder.pl
config.status: creating Examples/Makefile
config.status: creating Examples/Makefile.conf
config.status: creating Setup/Makefile
config.status: creating Sources/API/Makefile
config.status: creating Sources/Application/Makefile
config.status: creating Sources/Core/Makefile
config.status: creating Sources/Display/Makefile
config.status: creating Sources/GL/Makefile
config.status: creating Sources/GUI/Makefile
config.status: creating Sources/GUIStyleSilver/Makefile
config.status: creating Sources/Makefile
config.status: creating Sources/MikMod/Makefile
config.status: creating Sources/Network/Makefile
config.status: creating Sources/Signals/Makefile
config.status: creating Sources/Sound/Makefile
config.status: creating Sources/SDL/Makefile
config.status: creating Sources/Vorbis/Makefile
config.status: creating Tests/Makefile.conf
config.status: executing depfiles commands
------------------------------------------------------------------------------
The following modules will be built:

                     clanGL = no
                    clanSDL = yes
                    clanApp = yes
                    clanGUI = yes
                   clanCore = yes
                  clanSound = yes
                clanNetwork = yes
                clanSignals = yes
                clanDisplay = yes
                 clanMikmod = yes
                 clanVorbis = yes

        Build Documentation = no
                Debug Build = no
------------------------------------------------------------------------------
Configure done.

Type 'make' to compile ClanLib.

a treba Glob2
Code:

D_REENTRANT  -march=i686 -O2 -pipe -fomit-frame-pointer -Wall -g -c FileManager.cpp
GraphicContext.cpp: In member function `virtual void
   GAGCore::DrawableSurface::drawSurface(int, int, GAGCore::DrawableSurface*,
   int, int, int, int, unsigned char)':
GraphicContext.cpp:1044: error: `GL_BGRA' undeclared (first use this function)
GraphicContext.cpp:1044: error: (Each undeclared identifier is reported only
   once for each function it appears in.)
GraphicContext.cpp:1044: error: `GL_UNSIGNED_BYTE' undeclared (first use this
   function)
GraphicContext.cpp:1044: error: `glReadPixels' undeclared (first use this
   function)
GraphicContext.cpp: In member function `virtual bool
   GAGCore::GraphicContext::setRes(int, int, unsigned int)':
GraphicContext.cpp:1777: error: `glState' undeclared (first use this function)
distcc[25634] ERROR: compile GraphicContext.cpp on localhost failed
make[3]: *** [GraphicContext.o] Error 1
make[3]: *** Waiting for unfinished jobs....
make[3]: Leaving directory `/var/tmp/portage/glob2-0.8.17/work/glob2-0.8.17/libgag/src'
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory `/var/tmp/portage/glob2-0.8.17/work/glob2-0.8.17/libgag'
make[1]: *** [all-recursive] Error 1
make[1]: Leaving directory `/var/tmp/portage/glob2-0.8.17/work/glob2-0.8.17'
make: *** [all-recursive-am] Error 2

!!! ERROR: games-strategy/glob2-0.8.17 failed.
!!! Function src_compile, Line 46, Exitcode 2

nevim nekde je neco spatne a ja nevim co
kdyz nekoho neco napadne sem s tim napadem hned ....diky
Back to top
View user's profile Send private message
Martin.M
n00b
n00b


Joined: 14 Feb 2006
Posts: 1

PostPosted: Wed Feb 15, 2006 10:19 am    Post subject: Zas jeden pribyl;)) Reply with quote

Tak se taky hlasim;) Mam notebook HP nx6125 PY533ES, cili sempron verze... Pokud jste nekdo stejne postizeni, dejte vedet.

Jeste jsem poradne nerochodil grafiku, zvuk nejede vubec, ale hlavne mam trosku problem s procesorem, docela hodne hreje a vetrak se spusti jen semtam, a ne pozvolna, ale proste naplno... Taky se mi nepozdava nejak vykon, prijde mi to hodne pomale, ac cpufreq-info hlasi 1.8Ghz... Taky se stava, ze to proste na par sekund zatuhne...;((

Mam gentoo 2005.1 jadro 2.6.15-gentoo-r5

Jinak mam jeste problemy s kde. Kdyz kliknu na KMenu, tak mi vyskoci hlaska, ted si nevpomenu presne, neco o tom, ze se nepodarilo vytvorit io-slave a ze klauncher rika, ze nezna protokol system ;(( Po druhe kdyz kliknu tak se menu normalne otevre...

Jinak si ovsem nemuzu gentoo vynachvalit, je super nemit tam zbytecneho balastu;))

P.S.: Nevite nekdo jak na podporu vice monitoru?? Mam pripojene jeste LCD a chtel bych rozsireny desktop, nebo jeste lepe, samostatny desktop na danem monitoru (nejlepe i se spodni listou s programama), ale totalne nevim jestli to jde udelat;)


Gentoo zdar;)
Back to top
View user's profile Send private message
Botanicus
n00b
n00b


Joined: 21 Feb 2006
Posts: 2

PostPosted: Tue Feb 21, 2006 1:00 am    Post subject: Postinstala&#269;ní konfigurace: rozlišení, dynamick Reply with quote

Zdravím :-) Právě jsem nainstaloval Gentoo, mám z něj moc velkou radost, ale potřebuji ještě pár věcí doladit...
1) rozlišení - mám ntb s LCD a naprostá většina Linux dister mi jej nastavila špatně - taková ty rpmková na 800x600, ta lepší - Debian a spol na 1024x768. A stejně tak Gentoo - vyšel jsem s 1024x768 a obnovovací frekvencí 0 (???což nechápu, ale takto se to zobrazuje...) Hledal jsem svůj oblíbený xorg.conf, ale utřel jsem...Asi mi nezbyde, než to zkonfigurovat přinejmenším pomocí Xorg -configure, že jo? Mne to hlásí, že mi to nechce najít myš, což nechápu proč a tak, prostě z toho nastavení, co to vytvořilo jsem si Xka nepustil...
2) co dělat, aby se to dynamicky taktovalo - mám Pentium M, pro tento procesor jsem si přirozeně zkompiloval jádro, ale teď co?
3) docela blbá věc - neroluje mi myš ani touchpad (chtěl bych, aby roloval jak shora dolů, ale i zprava doleva)
4) Ono mi to nehraje...nainstaloval jsem mp3blaster a amarok a ani jedno nehraje...co mám emergnout? Jinak zvuk jde...
Za rady děkuji! J

PS: Proboha hlavně ne odkazy na anglické stránky, snažil jsem se, ALE...
Back to top
View user's profile Send private message
Botanicus
n00b
n00b


Joined: 21 Feb 2006
Posts: 2

PostPosted: Tue Feb 21, 2006 11:37 am    Post subject: Re: Postinstala&#269;ní konfigurace: rozlišení, dynam Reply with quote

Trochu jsem s tím pokročil - rozlišení jsem vyřešil trochu prasácky (konfigurace Xek mi nedetekovala myš a s tou novou konfigurací se nedalo ani zalogovat...) tak jsem zkopíroval nastavení Xek z Debianu a poupravil...takže to šlape.
Ale pořád nevím, co s tím taktováním, myší (ta mne štve hodně) a ten zvuk - zvuk jako takový jde (v Gaimu), ale v Amaroku a mp3blasteru ne..
Jo a když se zalogovávám, tak mi to hlásí, že gentoo není v /etc/hosts, něco s internetem a Gentoo se v té hlášce píše...A Gnome mne to sice pustí, ale štve mne to...J
Back to top
View user's profile Send private message
Mr.Neutron
n00b
n00b


Joined: 02 Apr 2005
Posts: 11
Location: Czech republic

PostPosted: Thu Mar 02, 2006 10:21 am    Post subject: Ups apc Reply with quote

Cauky,
mame na APC Smart UPS 1500 napojene servery s OS Linux (Gentoo, ipCop), w2k a Win NT. Nemate nekdo nejakou zkusenost jestli PowerChute dokaze schazovat veskere tyto rozlicne OS? Jde mi predevsim o Gentoo server na kterym bezi ucetni SW a pak o w2k server (jeste jsme ho stale nebyli schopne zcela vyradit :(
_________________
Mr Neutron: "Mrs S, I can eat enormous quantities of ice cream without being sick."
Back to top
View user's profile Send private message
Arteal
n00b
n00b


Joined: 05 Mar 2006
Posts: 6
Location: Brno.CZ

PostPosted: Sun Mar 05, 2006 9:02 pm    Post subject: Reply with quote

nevíte nìkdo jestli se dá rozjet grafický instalátor s menší obnovovací frekvenci? popø. menším rozlišením ? jede primárnì na 1024x768@75 ale mùj poje**** monitor si dá jen 1024x768@60
Back to top
View user's profile Send private message
CZTomi
n00b
n00b


Joined: 01 Apr 2006
Posts: 5

PostPosted: Sat Apr 01, 2006 5:24 pm    Post subject: Reply with quote

Ahoj, nechal jsem se zlákat a přes GPRS (!) jsem rozchodil Gentoo, problémy byly, ale spíš mezi židlí a klávesama, ale povidlo se. Krom jedné věci můžu teď hned opustit závistlostma zdevastované SuSE a použít novou instalaci. Ta jedna věc je připojování kamery. Má interní paměť 32MB a SD kartu. Normálně se to připojuje jako sda1 a sdb1, pod některejma Woknama taky, pod jinejma Win a taky bohužel pod Gentoo vidím jen těch prázdnejch 32Mega, ta SD karta plná fotek vidět není. víc zde:
http://forums.gentoo.org/viewtopic-p-3224693.html#3224693
Nemáte někdo nějakej nápad?
Back to top
View user's profile Send private message
CZTomi
n00b
n00b


Joined: 01 Apr 2006
Posts: 5

PostPosted: Sun Apr 23, 2006 8:15 pm    Post subject: Reply with quote

Po pár pokusech s kompilací jádra vyřešeno.
Back to top
View user's profile Send private message
dekon
Tux's lil' helper
Tux's lil' helper


Joined: 21 Aug 2005
Posts: 80

PostPosted: Wed May 03, 2006 2:30 pm    Post subject: Reply with quote

No a nemohl bys napsat co si do toho jadra pridal ?
_________________
Sorry for my English,i am not good at in this :)
Back to top
View user's profile Send private message
tokos
n00b
n00b


Joined: 07 Nov 2006
Posts: 1

PostPosted: Wed Nov 08, 2006 7:15 am    Post subject: Jihoèeský tuèòák Reply with quote

Zdravim ptáky linuxáky. Øadím se mezi spokojené uživatele Gentoo. I když obèas jsem i v SUSE:) Jinak zatim malièkej problém s 3Dakcelerací na notebooku u Gentoo s integrovanou grafikou SiS.
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Other Languages All times are GMT
Goto page Previous  1, 2, 3, 4, 5, 6, 7  Next
Page 6 of 7

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum