View previous topic :: View next topic |
Author |
Message |
kamikaze04 Guru
Joined: 28 Mar 2004 Posts: 366 Location: Valencia-Spain
|
Posted: Tue Jul 05, 2005 7:42 pm Post subject: DMA not working on acer tm 4150 |
|
|
Hello everybody,
I have just installed my gentoo on an acer travelmate 4150. Everything works fine, except the fact that i cannnot enable DMA. I have tried everything, and now i copy my tests with hdparm,and kernel config to see if you could help me:
Code: |
Apolo-bis ~ # hdparm /dev/hdc
/dev/hdc:
multcount = 16 (on)
IO_support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 0 (off)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
geometry = 16383/255/63, sectors = 60011642880, start = 0
|
Code: |
Apolo-bis ~ # hdparm -i /dev/hdc
/dev/hdc:
Model=IC25N060ATMR04-0, FwRev=MO3OAD4A, SerialNo=MRA301KEKZWGVH
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=7884kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=117210240
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=yes: mode=0xFE (254) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:
* signifies the current active mode
|
Code: |
hdparm -I /dev/hdc
.....
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Vendor, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: 254 (0xfe)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
....
|
Code: |
Apolo-bis ~ # hdparm -d1 /dev/hdc
/dev/hdc:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)
|
And here my kernel config, (if you need more, just tell me)
Code: |
<*> ATA/ATAPI/MFM/RLL support │ │
│ │ <*> Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support
│ │ --- Please see Documentation/ide.txt for help/info on IDE drives
│ │ [ ] Support for SATA (deprecated; conflicts with libata SATA driver)
│ │ [ ] Use old disk-only driver on primary interface
│ │ <*> Include IDE/ATA-2 DISK support
│ │ [*] Use multi-mode by default
│ │ <*> PCMCIA IDE support
│ │ <*> Include IDE/ATAPI CDROM support
│ │ < > Include IDE/ATAPI TAPE support (EXPERIMENTAL)
│ │ <*> SCSI emulation support
│ │ [*] IDE Taskfile Access
│ │ --- IDE chipset support/bugfixes
│ │ <*> generic/default IDE chipset support
│ │ [*] CMD640 chipset bugfix/support
│ │ [ ] CMD640 enhanced support
│ │ [*] PCI IDE chipset support
│ │ [*] Sharing PCI IDE interrupts support
│ │ [ ] Boot off-board chipsets first support
│ │ <*> Generic PCI IDE Chipset Support
│ │ < > OPTi 82C621 chipset enhanced support (EXPERIMENTAL)
│ │ < > RZ1000 chipset bugfix/support
[*] Generic PCI bus-master DMA support
│ │ [ ] Force enable legacy 2.0.X HOSTS to use DMA
│ │ [*] Use PCI DMA by default when available
│ │ [ ] Enable DMA only for disks
│ │ < > AEC62XX chipset support
|
And here the output from lspci
Code: |
Apolo-bis ~ # lspci
0000:00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
0000:00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
0000:00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
0000:00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04)
0000:00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 04)
0000:00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 04)
0000:00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 04)
0000:00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 04)
0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4)
0000:00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 04)
0000:00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 04)
0000:00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 04)
0000:00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 04)
0000:00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 04)
0000:01:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link)
0000:01:01.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
0000:01:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev 05)
|
Any ideas will be good. Thanks a lot! _________________ Todo lo que quisiste saber sobre google en: www.noticiasgoogle.es |
|
Back to top |
|
|
NeddySeagoon Administrator
Joined: 05 Jul 2003 Posts: 54216 Location: 56N 3W
|
Posted: Tue Jul 05, 2005 8:05 pm Post subject: |
|
|
kamikaze04,
Further down the menu from Code: | [*] PCI IDE chipset support | You need to turn on the PXII Chipset Support then rebuild your kernel. It must be built in, not a module. _________________ Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
Back to top |
|
|
kamikaze04 Guru
Joined: 28 Mar 2004 Posts: 366 Location: Valencia-Spain
|
Posted: Tue Jul 05, 2005 10:17 pm Post subject: |
|
|
thanks NeddySeagoon,
but... ...sorry, i forgot to copy/paste that line too...
I have tried with and without the pxiin support, but still having the same result, no DMA.
Any one could point me about my missconfiguration?
Thanks a los. _________________ Todo lo que quisiste saber sobre google en: www.noticiasgoogle.es |
|
Back to top |
|
|
NeddySeagoon Administrator
Joined: 05 Jul 2003 Posts: 54216 Location: 56N 3W
|
Posted: Tue Jul 05, 2005 10:31 pm Post subject: |
|
|
kamikaze04,
That chip can be dificult to set up for DMA. If you look in lspci you will see its listed as a SATA driver but it controls your CD-ROM as /dev/hdc.
It has two configuration settings in the kernel and posiibly your BIOs too. Try adding in SCSI support, SCSI Disk Support and under Low Level SCSI Drivers, SATA and PIIX. _________________ Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
Back to top |
|
|
Winamp n00b
Joined: 10 Jul 2005 Posts: 4
|
Posted: Sun Jul 10, 2005 7:14 am Post subject: |
|
|
Have the same problem ((
Added all of that NeddySeagoon said, but still no result (now ata can't find any devices) _________________ Mitsubishi Pajero IO Rules |
|
Back to top |
|
|
NeddySeagoon Administrator
Joined: 05 Jul 2003 Posts: 54216 Location: 56N 3W
|
Posted: Sun Jul 10, 2005 8:51 am Post subject: |
|
|
Winamp,
Please post your lspci output.
Lines that mention SATA and/or IDE will be enough. _________________ Regards,
NeddySeagoon
Computer users fall into two groups:-
those that do backups
those that have never had a hard drive fail. |
|
Back to top |
|
|
Winamp n00b
Joined: 10 Jul 2005 Posts: 4
|
Posted: Sun Jul 10, 2005 12:04 pm Post subject: |
|
|
Here is my lspci output:
Code: |
0000:00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
0000:00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
0000:00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
0000:00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04)
0000:00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 04)
0000:00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 04)
0000:00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 04)
0000:00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 04)
0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4)
0000:00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 04)
0000:00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 04)
0000:00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 04)
0000:00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 04)
0000:00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 04)
0000:01:00.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link)
0000:01:01.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
0000:01:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev 05)
0000:01:04.0 CardBus bridge: ENE Technology Inc CB-712/4 Cardbus Controller (rev 10)
0000:01:04.1 FLASH memory: ENE Technology Inc: Unknown device 0530 (rev 01)
0000:01:04.2 Class 0805: ENE Technology Inc: Unknown device 0550 (rev 01)
0000:01:04.3 FLASH memory: ENE Technology Inc: Unknown device 0520 (rev 01)
0000:01:04.4 FLASH memory: ENE Technology Inc: Unknown device 0551 (rev 01)
|
With this kernel configuration (ide & scsi only):
Code: |
#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDESCSI=m
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_CMD640=y
CONFIG_BLK_DEV_IDEPNP=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_BLK_DEV_IDEDMA_FORCED=y
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_PIIX=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_AUTO=y
#
# SCSI device support
#
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_BLK_DEV_SR=y
CONFIG_CHR_DEV_SG=y
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
#
# SCSI Transport Attributes
#
CONFIG_SCSI_FC_ATTRS=y
#
# SCSI low-level drivers
#
CONFIG_SCSI_SATA=y
CONFIG_SCSI_ATA_PIIX=y
CONFIG_SCSI_QLA2XXX=y
CONFIG_SCSI_QLA22XX=y
|
I get /dev/hdc as my HDD and /dev/hdd as my optical drive... so I cannot turn on dma for them...
But when I turn select ide section in kernel configuration as module, I get the following - http://www.carbotec.ru/img/acer_nb.jpg
Thank you in advance _________________ Mitsubishi Pajero IO Rules |
|
Back to top |
|
|
Winamp n00b
Joined: 10 Jul 2005 Posts: 4
|
Posted: Tue Jul 12, 2005 11:29 am Post subject: |
|
|
So no ideas at all??? (( _________________ Mitsubishi Pajero IO Rules |
|
Back to top |
|
|
gama n00b
Joined: 14 Mar 2004 Posts: 13
|
Posted: Mon Jul 25, 2005 10:53 pm Post subject: DMA not working on acer tm 4150 |
|
|
I have the same notebook tm 4152lmi and searching in the net i try to change the libata.h file but i didin't enable dma for the disk and the dvd.
Anyone had found the solution please |
|
Back to top |
|
|
schlummerkissen n00b
Joined: 18 Jun 2005 Posts: 39 Location: Ludwigshafen am Rhein (Germany)
|
Posted: Tue Jul 26, 2005 12:41 pm Post subject: |
|
|
i own a travelmate 4101 wlmi and after some kernel changes i got dma running here is my config
Quote: |
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
CONFIG_IDE_TASK_IOCTL=y
#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_IDEPNP is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set
|
maybe you need some more changes but here it works, and i dont think that your notebook has much differences. |
|
Back to top |
|
|
gama n00b
Joined: 14 Mar 2004 Posts: 13
|
Posted: Tue Jul 26, 2005 9:20 pm Post subject: DMA not working on acer tm 4150 |
|
|
Thank you in advance schlummerkissen, now I try your kernel configuration, but first only one question: did you enable some scsi support in your kernel? The hard disk e dvd are always hdc and hdd? |
|
Back to top |
|
|
schlummerkissen n00b
Joined: 18 Jun 2005 Posts: 39 Location: Ludwigshafen am Rhein (Germany)
|
Posted: Tue Jul 26, 2005 9:36 pm Post subject: |
|
|
my hard disk is /dev/hda
and my dvd is /dev/cdrom
i have compiled some scsi-stuff, but only as modules and not loaded.
It should work without. |
|
Back to top |
|
|
gama n00b
Joined: 14 Mar 2004 Posts: 13
|
Posted: Wed Jul 27, 2005 9:38 am Post subject: DMA not working on acer tm 4150 |
|
|
Thank you schlummerkissen, but yours kernel configuration don't work for me. I can't enable dma for the disk and dvd so my notebook it's very slow and I can't burn anythings in my dvd-rw. For information my disc it's /dev/hdc and the dvd it's /dev/hdd. I tried to disable in the kernel all ide drivers as suggested in this thread: https://forums.gentoo.org/viewtopic-t-356273-start-0-postdays-0-postorder-asc-highlight-.html
but I can't boot y gentoo due to kernel panic.
Any suggsuggestion? |
|
Back to top |
|
|
13Homer Guru
Joined: 12 Jul 2005 Posts: 461
|
Posted: Wed Jul 27, 2005 10:34 am Post subject: |
|
|
I had similar problem with my Acer Aspire 5012. The solution was enabling (built-in into kernel) ATI IXP chipset (AIR the only not compiled in by default!).
I didn't change other settings. And it started working.
Maybe try enable all chipsets?
Uh! And sorry for my english |
|
Back to top |
|
|
schlummerkissen n00b
Joined: 18 Jun 2005 Posts: 39 Location: Ludwigshafen am Rhein (Germany)
|
Posted: Wed Jul 27, 2005 2:41 pm Post subject: |
|
|
maybe you try first to run a live-cd like kanotix and test if dma mode runs there.
Then you could compare the config of the life-cd and the loaded modules etc. with your gentoo-kernel.
May be it could help you. |
|
Back to top |
|
|
gama n00b
Joined: 14 Mar 2004 Posts: 13
|
Posted: Wed Jul 27, 2005 8:30 pm Post subject: DMA not working on acer tm 4150 |
|
|
I tried enable all the ide chipset but nothing all the same; then I booted knoppix live cd but also this linux distribution don't enable dma; i tried Mandriva 10.1 the same things; at the end I tried Ubuntu 5.04 but was impossible to boot the live-cd because the distribution didn't see the cdrom (dvdrom). Now I'm downloading kanotix and ...... |
|
Back to top |
|
|
gama n00b
Joined: 14 Mar 2004 Posts: 13
|
Posted: Wed Jul 27, 2005 10:24 pm Post subject: DMA not working on acer tm 4150 (Solved for me) |
|
|
Finally I apply manually this patch: http://marc.theaimsgroup.com/?l=linux-ide&m=112032992832526&w=2 at the gentoo-sources kernel (adding manually the four line in the piix.c file because the command patch -p0 < ...... didn't work for me), recompiling the kernel without any SCSI and PATA drivers and now dma is working.
Thanks to all. |
|
Back to top |
|
|
Mos n00b
Joined: 17 Mar 2003 Posts: 48 Location: Brussels, Belgium
|
Posted: Sun Sep 11, 2005 8:30 pm Post subject: |
|
|
worked for me too, on my acer tm 4150.
Thanks alot gama !! |
|
Back to top |
|
|
gentleman Tux's lil' helper
Joined: 02 Dec 2005 Posts: 140 Location: Germany, Paderborn
|
Posted: Fri Mar 31, 2006 3:29 pm Post subject: |
|
|
Hm, I'm just too stupid to understand what I have to do here. Can s.o. explain what four lines have to be cpoied to which file? I get a little bit confused by page behind this link =).
Thanks a lot. _________________ Everything works, you just have to do it correctly. |
|
Back to top |
|
|
gama n00b
Joined: 14 Mar 2004 Posts: 13
|
Posted: Sun Apr 02, 2006 1:05 pm Post subject: |
|
|
Now, with the new gentoo kernel is not necessary to apply that patch.
In the kernel 2.6.15-r7 and newer it's sufficient enable SCSI disk support - SCSI generic support - Serial ATA (SATA) support - AHCI SATA support - Intel PIIX/ICH SATA support. In this way the hard disk will be SDA and the cdrom SR0 and the DMA is always on. Remember to change the fstab before rebooting. |
|
Back to top |
|
|
djedy n00b
Joined: 10 Apr 2006 Posts: 1
|
Posted: Mon Apr 10, 2006 5:39 pm Post subject: |
|
|
hi,i compiled the kernel with that options & without IDE,but iafter boot it hangs in grub,with a mesage about error 17
can anybody help m? |
|
Back to top |
|
|
gama n00b
Joined: 14 Mar 2004 Posts: 13
|
Posted: Tue Apr 11, 2006 8:01 pm Post subject: |
|
|
I don't use grub so I don't know the error 17 but are you sure you changed the file etc/grub.conf with the new disk?
Remember that now the hard disk is recognize as SCSI disk |
|
Back to top |
|
|
kamikaze04 Guru
Joined: 28 Mar 2004 Posts: 366 Location: Valencia-Spain
|
Posted: Mon Jul 03, 2006 8:47 am Post subject: |
|
|
I also did the same. I applied the patch and dma is now on.
The patch is
Code: |
diff -Naurp linux-2.6.16.orig/drivers/ide/pci/piix.c linux-2.6.16/drivers/ide/pci/piix.c
--- linux-2.6.16.orig/drivers/ide/pci/piix.c 2006-03-20 06:53:29.000000000 +0100
+++ linux-2.6.16/drivers/ide/pci/piix.c 2006-03-24 00:29:34.000000000 +0100
@@ -132,6 +132,7 @@ static u8 piix_ratemask (ide_drive_t *dr
case PCI_DEVICE_ID_INTEL_82801DB_11:
case PCI_DEVICE_ID_INTEL_82801EB_11:
case PCI_DEVICE_ID_INTEL_ESB_2:
+ case PCI_DEVICE_ID_INTEL_ICH6_5:
case PCI_DEVICE_ID_INTEL_ICH6_19:
case PCI_DEVICE_ID_INTEL_ICH7_21:
case PCI_DEVICE_ID_INTEL_ESB2_18:
@@ -447,6 +448,7 @@ static unsigned int __devinit init_chips
case PCI_DEVICE_ID_INTEL_82801EB_11:
case PCI_DEVICE_ID_INTEL_82801E_11:
case PCI_DEVICE_ID_INTEL_ESB_2:
+ case PCI_DEVICE_ID_INTEL_ICH6_5:
case PCI_DEVICE_ID_INTEL_ICH6_19:
case PCI_DEVICE_ID_INTEL_ICH7_21:
case PCI_DEVICE_ID_INTEL_ESB2_18:
@@ -578,6 +580,7 @@ static ide_pci_device_t piix_pci_info[]
/* 22 */ DECLARE_PIIX_DEV("ICH4"),
/* 23 */ DECLARE_PIIX_DEV("ESB2"),
/* 24 */ DECLARE_PIIX_DEV("ICH8M"),
+ /* 25 */ DECLARE_PIIX_DEV("ICH6M"),
};
/**
@@ -655,6 +658,7 @@ static struct pci_device_id piix_pci_tbl
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 22},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_18, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 23},
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_6, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 24},
+ { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH6_5, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 25},
{ 0, },
};
MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
diff -Naurp linux-2.6.16.orig/include/linux/pci_ids.h linux-2.6.16/include/linux/pci_ids.h
--- linux-2.6.16.orig/include/linux/pci_ids.h 2006-03-20 06:53:29.000000000 +0100
+++ linux-2.6.16/include/linux/pci_ids.h 2006-03-24 00:28:35.000000000 +0100
@@ -2092,6 +2092,7 @@
#define PCI_DEVICE_ID_INTEL_ICH6_0 0x2640
#define PCI_DEVICE_ID_INTEL_ICH6_1 0x2641
#define PCI_DEVICE_ID_INTEL_ICH6_2 0x2642
+#define PCI_DEVICE_ID_INTEL_ICH6_5 0x2653
#define PCI_DEVICE_ID_INTEL_ICH6_16 0x266a
#define PCI_DEVICE_ID_INTEL_ICH6_17 0x266d
#define PCI_DEVICE_ID_INTEL_ICH6_18 0x266e
|
Good luck _________________ Todo lo que quisiste saber sobre google en: www.noticiasgoogle.es |
|
Back to top |
|
|
blue_american Tux's lil' helper
Joined: 16 Sep 2005 Posts: 92 Location: Coimbra, Portugal
|
Posted: Tue Sep 19, 2006 4:40 pm Post subject: |
|
|
I tried your patch (also downloaded 2.6.16 kernel) and I got:
dunkelheit ~ # patch -p0 < piix.patch
patching file linux-2.6.16/drivers/ide/pci/piix.c
Hunk #1 FAILED at 132.
Hunk #2 FAILED at 448.
Hunk #3 FAILED at 580.
Hunk #4 FAILED at 658.
4 out of 4 hunks FAILED -- saving rejects to file linux-2.6.16/drivers/ide/pci/piix.c.rej
dunkelheit ~ # patch -p0 < pci_ids.patch
patching file linux-2.6.16/include/linux/pci_ids.h
Hunk #1 FAILED at 2092.
1 out of 1 hunk FAILED -- saving rejects to file linux-2.6.16/include/linux/pci_ids.h.rej
Any ideias? |
|
Back to top |
|
|
|