View previous topic :: View next topic |
Author |
Message |
rmautino n00b
Joined: 31 Dec 2004 Posts: 33
|
Posted: Tue Mar 22, 2005 11:39 pm Post subject: Installed Gentoo....now it wont boot..... |
|
|
Hello,
I just finished a lengthy install on a Sunfire v100 from Stage 1.
I installed the SILO bootloadre as per the docs. Now when I reboot and remove the install CD, I get...
Code: |
Sun Fire V100 (UltraSPARC-IIe 548MHz), No Keyboard
OpenBoot 4.0, 1024 MB memory installed, Serial #59084099.
Ethernet address 0:3:ba:85:8d:43, Host ID: 83858d43.
Executing last command: boot
Boot device: disk File and args:
The file just loaded does not appear to be executable.
Boot device: disk File and args:
The file just loaded does not appear to be executable.
ok
|
My partition is like this:
Code: |
/dev/hda1 /boot
/dev/hda2 swap
/dev/hda3 whole disk
/dev/hda4 /usr
/dev/hda5 /var
/dev/hda6 /
|
My silo.conf is:
Code: |
# Example of how can be silo.conf set up
partition = 1
root = /dev/hda1
timeout = 150
#password = __put_your_password_in_cleartext_here__
#restricted
image = /boot/kernel-2.4.28
label = linux
|
Any ideas? |
|
Back to top |
|
|
irwinr Apprentice
Joined: 11 May 2004 Posts: 152 Location: Texas
|
Posted: Wed Mar 23, 2005 2:31 am Post subject: |
|
|
I don't know anything about SILO, but I know that with grub, whatever you define as your 'root=', is considered '/' throughout the rest of your config file.
IE: Where it says kernel=/boot/kernel...
It may actually be trying to load /boot/boot/kernel...
since /dev/hda1 is defined as your root (And your /dev/hda1 is /boot)
Just a thought, again, I've never used SILO.
-Jeremy |
|
Back to top |
|
|
leonarp n00b
Joined: 22 Mar 2004 Posts: 35 Location: Kansas
|
Posted: Thu Mar 24, 2005 2:26 pm Post subject: Re: Installed Gentoo....now it wont boot..... |
|
|
Quote: | My silo.conf is:
Code: |
# Example of how can be silo.conf set up
partition = 1
root = /dev/hda1
timeout = 150
#password = __put_your_password_in_cleartext_here__
#restricted
image = /boot/kernel-2.4.28
label = linux
|
|
Shouldn't the root entry read
Last edited by leonarp on Thu Mar 24, 2005 5:16 pm; edited 1 time in total |
|
Back to top |
|
|
Weeve Retired Dev
Joined: 30 Oct 2002 Posts: 641
|
Posted: Thu Mar 24, 2005 5:06 pm Post subject: |
|
|
Yes |
|
Back to top |
|
|
lianlian n00b
Joined: 09 Apr 2005 Posts: 30
|
Posted: Sun Apr 10, 2005 11:29 pm Post subject: |
|
|
i need to change my silo.conf, how can i do that now sense i already rebooted(first time) and it gives that same error too. so how can i change my silo.conf?
i changed my silo.conf now, i learned a lot from gentoo, but still can't get it to boot properly |
|
Back to top |
|
|
w.hill Tux's lil' helper
Joined: 23 Jan 2005 Posts: 133 Location: Perth, Western Australia
|
Posted: Mon Apr 11, 2005 11:58 am Post subject: |
|
|
After you alter /etc/silo.conf you then have to run silo.
/sbin/silo me thinks. Then reboot. |
|
Back to top |
|
|
leonarp n00b
Joined: 22 Mar 2004 Posts: 35 Location: Kansas
|
Posted: Mon Apr 11, 2005 2:50 pm Post subject: |
|
|
If your silo config file is in /boot then
Code: | /sbin/silo -C /boot/silo.conf |
or if it is in /etc
Code: | /sbin/silo -C /etc/silo.conf |
|
|
Back to top |
|
|
|