HOWTO: ATI Radeon Mobility 7500 and Sony GRX560 laptop

Message

nrdu · Post by **nrdu** » Sun Oct 31, 2004 12:05 am

There has been a lot of problems with this card, and all the information is just 'floating' around, bits and pices, but no one seams to have actualy put everything together. Well I got it working, reaching up to 1800fps (average about 1500 or so).

This was done on a Sony GRX560 using the 2.6 kernel (ck-sources) using Xorg. I dunno if it will work with the 2.4, or the normal dev-sources... I got it working, and stopped there.

Things that should be enabled in this kernel:

Code: Select all

Processor type and features  --->  

[*] MTRR (Memory Type Range Register) support         

Device Drivers  --->  Character devices  --->

<*> /dev/agpgart (AGP Support)   
<*>   Intel 440LX/BX/GX, I8xx and E7x05 chipset support    

[*] Direct Rendering Manager (XFree86 4.1.0 and higher DRI support) 
    <*>   ATI Radeon

In your /etc/make.conf add "opengl" to your use flags and emerge xorg-x11. You will also need to emerge 'opengl-update'

My /etc/X11/xorg.conf file:

Code: Select all

Section "ServerLayout"
        Identifier     "X.org Configured"
        Screen      0  "Screen0" 0 0
#       InputDevice    "Touchpad"  "CorePointer"
#       InputDevice     "USBMouse" "AlwaysCore"
#       InputDevice     "USBMouse" "CorePointer"
        InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
        RgbPath      "/usr/X11R6/lib/X11/rgb"
        ModulePath   "/usr/X11R6/lib/modules"
        FontPath     "/usr/share/fonts/misc/"
        FontPath     "/usr/share/fonts/TTF/"
        FontPath     "/usr/share/fonts/Speedo/"
        FontPath     "/usr/share/fonts/Type1/"
#       FontPath     "/usr/share/fonts/CID/"
        FontPath     "/usr/share/fonts/75dpi/"
        FontPath     "/usr/share/fonts/100dpi/"
EndSection

Section "Module"
        Load  "record"
        Load  "extmod"
        Load  "dbe"
        Load  "dri"
        Load  "glx"
        Load  "xtrap"
        Load  "freetype"
        Load  "type1"
        Load  "speedo"
        Load  "radeon"
        Load   "drm"
EndSection

Section "DRI"
   Mode   0666
EndSection

Section "InputDevice"
        Identifier  "Keyboard0"
        Driver      "kbd"
EndSection

#Section "InputDevice"
#  Driver        "synaptics"
#  Identifier    "Touchpad"
#  Option        "Device"        "/dev/psaux"
#  Option        "Protocol"      "auto-dev"
#  Option        "LeftEdge"      "1900"
#  Option        "RightEdge"     "5400"
#  Option        "TopEdge"       "3900"
#  Option        "BottomEdge"    "1800"
#  Option        "FingerLow"     "25"
#  Option        "FingerHigh"    "30"
#  Option        "MaxTapTime"    "180"
#  Option        "MaxTapMove"    "220"
#  Option        "VertScrollDelta" "100"
#  Option        "MinSpeed"      "0.02"
#  Option        "MaxSpeed"      "0.18"
#  Option        "AccelFactor" "0.0010"
##  Option       "Repeater"      "/dev/ps2mouse"
##  Option       "SHMConfig"     "on"
#EndSection

Section "InputDevice"
        Identifier  "USBMouse"
        Driver      "mouse"
        Option      "Protocol" "ExplorerPS/2"
        Option      "Device" "/dev/input/mice"
        Option      "Buttons" "7"
        Option      "ZAxisMapping" "4 5"
        Option      "Resolution" "1200"
EndSection


Section "Monitor"
        Identifier   "Monitor0"
        VendorName   "Monitor Vendor"
        ModelName    "Monitor Model"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
        ### [arg]: arg optional
        Option          "Accel"
        #Option     "NoAccel"                   # [<bool>]
        #Option     "SWcursor"                  # [<bool>]
        #Option     "Dac6Bit"                   # [<bool>]
        #Option     "Dac8Bit"                   # [<bool>]
        #Option     "ForcePCIMode"              # [<bool>]
        #Option     "BusType"                   # [<str>]
        #Option     "CPPIOMode"                 # [<bool>]
        #Option     "CPusecTimeout"             # <i>
        Option     "AGPMode"                    "4"
        Option     "AGPFastWrite"               "yes"
        #Option     "AGPSize"                   # <i>
        #Option     "GARTSize"                  # <i>
        #Option     "RingSize"                  # <i>
        #Option     "BufferSize"                # <i>
        #Option     "EnableDepthMoves"          # [<bool>]
        Option     "EnablePageFlip"             "yes"
        #Option     "NoBackBuffer"              # [<bool>]
        #Option     "DRIReinit"                 # [<bool>]
        #Option     "PanelOff"                  # [<bool>]
        Option     "DDCMode"                    "yes"
        #Option     "MonitorLayout"             # [<str>]
        #Option     "IgnoreEDID"                # [<bool>]
        #Option     "OverlayOnCRTC2"            # [<bool>]
        #Option     "CloneMode"                 # [<str>]
        #Option     "CloneHSync"                # [<str>]
        #Option     "CloneVRefresh"             # [<str>]
        #Option     "UseFBDev"                  # [<bool>]
        #Option     "VideoKey"                  # <i>
        #Option     "DisplayPriority"           # [<str>]
        #Option     "PanelSize"                 # [<str>]
        #Option     "ForceMinDotClock"          # <freq>
        Identifier  "Card0"
#       Driver      "ati"
        Driver      "radeon"
        VendorName  "ATI Technologies Inc"
        BoardName   "Radeon Mobility M7 LW [Radeon Mobility 7500]"
        BusID       "PCI:1:0:0"
EndSection

Section "Screen"
        Identifier "Screen0"
        Device     "Card0"
        Monitor    "Monitor0"
        DefaultDepth  16
        SubSection "Display"
                Viewport   0 0
                Depth     1
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     4
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     8
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     15
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     16
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     24
        EndSubSection
EndSection

A few notes about this. I use an external USB Microsoft Optical Trackball, this config for some reason allows my trackball & the touchpad to work, even tho it's commented out. You may need to adjust on your setup.

Once you got all that done do:

Code: Select all

opengl-update xorg-x11

That should be it all. Here's my kernel config also:

Code: Select all

CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y

CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_LOCK_KERNEL=y

CONFIG_LOCALVERSION=""
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_SYSCTL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_HOTPLUG=y
CONFIG_KOBJECT_UEVENT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_KALLSYMS=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0

CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y

CONFIG_X86_PC=y
CONFIG_MPENTIUM4=y
CONFIG_X86_GENERIC=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_PREEMPT=y
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y

CONFIG_NOHIGHMEM=y
CONFIG_MTRR=y
CONFIG_HAVE_DEC_LOCK=y


CONFIG_ACPI=y
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_VIDEO=m
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
CONFIG_ACPI_IBM=m
CONFIG_ACPI_BLACKLIST_YEAR=0
CONFIG_ACPI_BUS=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y

CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_TABLE=y

CONFIG_X86_ACPI_CPUFREQ=y
CONFIG_X86_SPEEDSTEP_CENTRINO=y
CONFIG_X86_SPEEDSTEP_CENTRINO_ACPI=y
CONFIG_X86_SPEEDSTEP_CENTRINO_TABLE=y
CONFIG_X86_SPEEDSTEP_ICH=y
CONFIG_X86_P4_CLOCKMOD=y

CONFIG_X86_SPEEDSTEP_LIB=y

CONFIG_PCI=y
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
CONFIG_PCI_NAMES=y




CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_MISC=y


CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y


CONFIG_PARPORT=m


CONFIG_BLK_DEV_FD=y
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_CRYPTOLOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_INITRAMFS_SOURCE=""

CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y

CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y

CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDESCSI=m

CONFIG_IDE_GENERIC=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_GENERIC=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_PIIX=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_IDEDMA_AUTO=y

CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y

CONFIG_BLK_DEV_SD=y
CONFIG_BLK_DEV_SR=m
CONFIG_CHR_DEV_SG=m

CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y


CONFIG_SCSI_QLA2XXX=y



CONFIG_IEEE1394=m

CONFIG_IEEE1394_OUI_DB=y
CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y
CONFIG_IEEE1394_CONFIG_ROM_IP1394=y

CONFIG_IEEE1394_OHCI1394=m

CONFIG_IEEE1394_VIDEO1394=m
CONFIG_IEEE1394_SBP2=m
CONFIG_IEEE1394_ETH1394=m
CONFIG_IEEE1394_DV1394=m
CONFIG_IEEE1394_RAWIO=m
CONFIG_IEEE1394_CMP=m
CONFIG_IEEE1394_AMDTP=m


CONFIG_NET=y

CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_TCPDIAG=y



CONFIG_NETDEVICES=y
CONFIG_DUMMY=m


CONFIG_NET_ETHERNET=y
CONFIG_MII=y

CONFIG_NET_PCI=y
CONFIG_EEPRO100=y




CONFIG_NET_RADIO=y


CONFIG_HERMES=m

CONFIG_NET_WIRELESS=y

CONFIG_PPP=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPP_FILTER=y
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPPOE=m



CONFIG_INPUT=y

CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_JOYDEV=y

CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=y

CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
CONFIG_INPUT_JOYSTICK=y

CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y


CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_PRINTER=m


CONFIG_HW_RANDOM=y
CONFIG_RTC=y
CONFIG_SONYPI=y

CONFIG_AGP=y
CONFIG_AGP_ATI=y
CONFIG_AGP_INTEL=y
CONFIG_DRM=y
CONFIG_DRM_RADEON=y

CONFIG_I2C=y
CONFIG_I2C_CHARDEV=m

CONFIG_I2C_ALGOBIT=y
CONFIG_I2C_ALGOPCF=m

CONFIG_SCx200_ACB=m







CONFIG_FB=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_VESA=y
CONFIG_VIDEO_SELECT=y

CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y

CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y

CONFIG_SOUND=y

CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_SEQUENCER=y
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_SEQUENCER_OSS=y
CONFIG_SND_RTCTIMER=y


CONFIG_SND_AC97_CODEC=y
CONFIG_SND_INTEL8X0=y



CONFIG_USB=y

CONFIG_USB_DEVICEFS=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y

CONFIG_USB_UHCI_HCD=m

CONFIG_USB_AUDIO=m
CONFIG_USB_MIDI=m
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m

CONFIG_USB_STORAGE=y
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y

CONFIG_USB_HID=m
CONFIG_USB_HIDINPUT=y

CONFIG_USB_KBD=m
CONFIG_USB_MOUSE=m

CONFIG_USB_MDC800=m
CONFIG_USB_MICROTEK=m
CONFIG_USB_HPUSBSCSI=m

CONFIG_USB_DABUSB=m


CONFIG_USB_CATC=m
CONFIG_USB_KAWETH=m
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET=m

CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_BELKIN=y
CONFIG_USB_GENESYS=y
CONFIG_USB_NET1080=y
CONFIG_USB_PL2301=y
CONFIG_USB_KC2190=y

CONFIG_USB_ARMLINUX=y
CONFIG_USB_EPSON2888=y
CONFIG_USB_ZAURUS=y
CONFIG_USB_CDCETHER=y

CONFIG_USB_AX8817X=y

CONFIG_USB_USS720=m


CONFIG_USB_TIGL=m
CONFIG_USB_RIO500=m




CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=m
CONFIG_EXT3_FS_XATTR=y
CONFIG_JBD=m
CONFIG_FS_MBCACHE=y
CONFIG_REISERFS_FS=y
CONFIG_DNOTIFY=y
CONFIG_AUTOFS4_FS=y

CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_UDF_FS=m
CONFIG_UDF_NLS=y

CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_VFAT_FS=m
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"

CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
CONFIG_RAMFS=y

CONFIG_CRAMFS=m

CONFIG_NFS_FS=m
CONFIG_NFSD=m
CONFIG_LOCKD=m
CONFIG_EXPORTFS=m
CONFIG_SUNRPC=m
CONFIG_SMB_FS=m

CONFIG_MSDOS_PARTITION=y

CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"


CONFIG_EARLY_PRINTK=y


CONFIG_CRYPTO=y

CONFIG_CRC_CCITT=m
CONFIG_CRC32=y
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_PC=y

nrdu · Post by **nrdu** » Sun Oct 31, 2004 1:15 am

For those coming over from Cedega with the EQ problem, here is the orig post about using this card with EQ:

http://forums.gentoo.org/viewtopic.php?t=244967

For those that are Gentoo guys trying to get EQ working with this card here is the post over on Cedega:

http://transgaming.org/forum/viewtopic.php?p=6331#6331

JoKerTheFirst · Post by **JoKerTheFirst** » Sat Nov 06, 2004 12:02 pm

Thanks nrdu, you saved my life

it worked like a charm on my system
Asus L3540 (L3800-S family) , P4 1400 MHz, 256 RAM, ATI radeon mobility 7500 64Mb RAM, using gentoo-dev-sources 2.6.9-rc1 and xorg-6.8.0-r1
now I can score up to ~1200 on glxgears (was 300)

nrdu · Post by **nrdu** » Wed Nov 17, 2004 10:19 pm

Wow, I didn't think anyone would be able to follow my 'hack' of a HOWTO.

I'm happy to hear this helped someone else tho.

nightblade · Post by **nightblade** » Sat Nov 20, 2004 1:05 am

Just migrated from Xfree to Xorg.
Still have to fix synaptics functions, but apart from that everything works perfectly

Thanks for the hints, nrdu !

dpl · Post by **dpl** » Sat Dec 18, 2004 3:26 pm

This was the awesomest ting I found yesterday. It took me about 20 minutes and I had glxgears topping 1300. That, is fantastic.

One note though, you don't need this bit:

Code: Select all

Device Drivers  --->  Graphics support --->

<*>   ATI Radeon display support
     [*]     DDC/I2C for ATI Radeon support

and if you do have it enabled, you can't use framebuffer/bootsplash. I took it out and have no ill effects towards the 3d stuff.

Thanks a TON for posting how you did this, cause I was starting to lose faith that I would ever have 3d acceleration with my 7500 mobility.

- dpl

PMT · Post by **PMT** » Mon Dec 27, 2004 10:27 am

An unfortunate note.

I followed your guide, since my 3d accel stopped after I reinstalled gentoo [hard drive crash].

Now, an interesting thing happens.

glxinfo says I have direct rendering, but whenever I try glxgears or any similar apps, my entire system hangs. SysRq-I and SysRq-K do nothing, and I cannot do anything but SysRq-SUB.

Nothing is reported at the time of the incident in /var/log/messages or /var/log/Xorg.0.log, so I'm at a loss.

kdag · Post by **kdag** » Wed Jan 19, 2005 11:29 pm

well i didnt follow the instructions of this thread but im suffering the same exact problem.

as soon as i start glxgears X freezes

did you ( yea you, the one who posted above me ) solved your problem?

anyone has an idea of what can be wrong in my system?

i will reemerge xorg-x11 soon

thanks

Fallen_Angel · Post by **Fallen_Angel** » Thu Jan 20, 2005 12:15 pm

hi,

you have to downgrade x.org, because the new version is buggy

Code: Select all

emerge =xorg-x11-6.8.0-r3

or the older 6.7 version, it's up to you

nrdu · Post by **nrdu** » Mon Feb 28, 2005 7:21 am

dpl wrote:This was the awesomest ting I found yesterday. It took me about 20 minutes and I had glxgears topping 1300. That, is fantastic.

One note though, you don't need this bit:
Code: Select all
Device Drivers  --->  Graphics support --->

<*>   ATI Radeon display support
     [*]     DDC/I2C for ATI Radeon support 
and if you do have it enabled, you can't use framebuffer/bootsplash. I took it out and have no ill effects towards the 3d stuff.

Thanks a TON for posting how you did this, cause I was starting to lose faith that I would ever have 3d acceleration with my 7500 mobility.

- dpl

Thanks for pointing this out, I wasn't sure if I needed it or not, I've updated the first post.

nrdu · Post by **nrdu** » Mon Feb 28, 2005 7:26 am

Fallen_Angel wrote:hi,

you have to downgrade x.org, because the new version is buggy
Code: Select all
emerge =xorg-x11-6.8.0-r3 
or the older 6.7 version, it's up to you

I got my laptop back from the repair shop and after upgrading to 6.8.x, more ATI issues.

My next laptop is not going to have an ATI card, this I swear!

Anyway, some looking around and found this:
https://bugs.freedesktop.org/show_bug.cgi?id=1773

After putting:

Code: Select all

        Option       "DynamicClocks"            "true"

in my /etc/X11/xorg.conf file my glxgears is back to normal again.

I didn't update this in the first post because it's a 'bug' that I hope will have it's patched applied in the future and null this out.

badgers · Post by **badgers** » Fri Apr 08, 2005 2:27 pm

for those of you with the 7500 mobility on a laptop.
Can you suspend to ram?
Can you suspend to disk?

I have found some conflicting info on putting laptops to sleep with the 7500 mobility and it Waking back up correctly

alexbota · Post by **alexbota** » Sat Apr 09, 2005 9:24 pm

badgers wrote:for those of you with the 7500 mobility on a laptop.
Can you suspend to ram?
Can you suspend to disk?

I have found some conflicting info on putting laptops to sleep with the 7500 mobility and it Waking back up correctly

Suspend to ram works (at least with APM)... I didn't try suspend to disk yet.

badgers · Post by **badgers** » Sun Apr 10, 2005 2:00 am

could you detail a little more about your config.
I had read one post that you had to switch to a virtual console before suspending.
I am glad to hear you can suspend to ram.
Did you disable the ACPI in the kernel?

alexbota · Post by **alexbota** » Sun Apr 17, 2005 8:13 pm

badgers wrote: could you detail a little more about your config.
I had read one post that you had to switch to a virtual console before suspending.
I am glad to hear you can suspend to ram.
Did you disable the ACPI in the kernel?

There's no need to switch to a virtual console... at least i didn't need it for any kernel version from the last year or so. Yes, I have ACPI disabled in the kernel. And no problems when resuming except the screen looking strange for a few fractions of a second. I only found problems with suspend to ram with my wireless card (ndiswrapper). If I let the card plugged in the PCMCIA slot when suspending it freezes right after resume. Oh, and one more thing... I had some problems with the clock on 2.6.10 kernel... although in BIOS seemed to be right (I have a Dell C640 and I am able to enter the bios with Fn-F1 whenever I want) the system would report it wrong. Now it has been fixed in the last kernel. Now here is my kernel config:

Code: Select all

#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.11-gentoo-r5
# Sat Apr  9 23:58:34 2005
#
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y

#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_LOCK_KERNEL=y

#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
CONFIG_SYSCTL=y
# CONFIG_AUDIT is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_HOTPLUG=y
CONFIG_KOBJECT_UEVENT=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
# CONFIG_EMBEDDED is not set
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_FUTEX=y
CONFIG_EPOLL=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SHMEM=y
CONFIG_CC_ALIGN_FUNCTIONS=0
CONFIG_CC_ALIGN_LABELS=0
CONFIG_CC_ALIGN_LOOPS=0
CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set

#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
CONFIG_OBSOLETE_MODPARM=y
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
CONFIG_KMOD=y

#
# Processor type and features
#
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
# CONFIG_X86_NUMAQ is not set
# CONFIG_X86_SUMMIT is not set
# CONFIG_X86_BIGSMP is not set
# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
# CONFIG_X86_ES7000 is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
CONFIG_MPENTIUM4=y
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MK8 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_X86_GENERIC is not set
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_L1_CACHE_SHIFT=7
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_INTEL_USERCOPY=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
# CONFIG_SMP is not set
CONFIG_PREEMPT=y
CONFIG_PREEMPT_BKL=y
# CONFIG_X86_UP_APIC is not set
CONFIG_X86_TSC=y
CONFIG_X86_MCE=y
CONFIG_X86_MCE_NONFATAL=y
# CONFIG_TOSHIBA is not set
CONFIG_I8K=y
CONFIG_MICROCODE=y
CONFIG_X86_MSR=y
CONFIG_X86_CPUID=y

#
# Firmware Drivers
#
# CONFIG_EDD is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
CONFIG_HAVE_DEC_LOCK=y
# CONFIG_REGPARM is not set

#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
# CONFIG_PM_DEBUG is not set
# CONFIG_SOFTWARE_SUSPEND is not set

#
# ACPI (Advanced Configuration and Power Interface) Support
#
# CONFIG_ACPI is not set

#
# APM (Advanced Power Management) BIOS Support
#
CONFIG_APM=y
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
CONFIG_APM_DO_ENABLE=y
CONFIG_APM_CPU_IDLE=y
CONFIG_APM_DISPLAY_BLANK=y
# CONFIG_APM_RTC_IS_GMT is not set
# CONFIG_APM_ALLOW_INTS is not set
# CONFIG_APM_REAL_MODE_POWER_OFF is not set

#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
# CONFIG_CPU_FREQ_DEBUG is not set
CONFIG_CPU_FREQ_STAT=y
# CONFIG_CPU_FREQ_STAT_DETAILS is not set
# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y
CONFIG_CPU_FREQ_GOV_ONDEMAND=y
CONFIG_CPU_FREQ_TABLE=y

#
# CPUFreq processor drivers
#
# CONFIG_X86_POWERNOW_K6 is not set
# CONFIG_X86_POWERNOW_K7 is not set
# CONFIG_X86_POWERNOW_K8 is not set
# CONFIG_X86_GX_SUSPMOD is not set
# CONFIG_X86_SPEEDSTEP_CENTRINO is not set
CONFIG_X86_SPEEDSTEP_ICH=y
# CONFIG_X86_SPEEDSTEP_SMI is not set
# CONFIG_X86_P4_CLOCKMOD is not set
# CONFIG_X86_CPUFREQ_NFORCE2 is not set
# CONFIG_X86_LONGRUN is not set
# CONFIG_X86_LONGHAUL is not set

#
# shared options
#
CONFIG_X86_SPEEDSTEP_LIB=y
# CONFIG_X86_SPEEDSTEP_RELAXED_CAP_CHECK is not set

#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
# CONFIG_PCIEPORTBUS is not set
# CONFIG_PCI_LEGACY_PROC is not set
CONFIG_PCI_NAMES=y
# CONFIG_ISA is not set
# CONFIG_MCA is not set
# CONFIG_SCx200 is not set

#
# PCCARD (PCMCIA/CardBus) support
#
CONFIG_PCCARD=y
# CONFIG_PCMCIA_DEBUG is not set
CONFIG_PCMCIA=y
CONFIG_CARDBUS=y

#
# PC-card bridges
#
CONFIG_YENTA=y
CONFIG_PD6729=y
CONFIG_I82092=y
CONFIG_TCIC=y
CONFIG_PCCARD_NONSTATIC=y

#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set

#
# Executable file formats
#
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_MISC=y

#
# Device Drivers
#

#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y

#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set

#
# Parallel port support
#
CONFIG_PARPORT=y
CONFIG_PARPORT_PC=y
CONFIG_PARPORT_PC_CML1=y
# CONFIG_PARPORT_SERIAL is not set
CONFIG_PARPORT_PC_FIFO=y
# CONFIG_PARPORT_PC_SUPERIO is not set
# CONFIG_PARPORT_PC_PCMCIA is not set
CONFIG_PARPORT_OTHER=y
CONFIG_PARPORT_1284=y

#
# Plug and Play support
#

#
# Block devices
#
CONFIG_BLK_DEV_FD=y
CONFIG_PARIDE=y
CONFIG_PARIDE_PARPORT=y

#
# Parallel IDE high-level drivers
#
CONFIG_PARIDE_PD=m
CONFIG_PARIDE_PCD=m
CONFIG_PARIDE_PF=m
CONFIG_PARIDE_PT=m
CONFIG_PARIDE_PG=m

#
# Parallel IDE protocol modules
#
# CONFIG_PARIDE_ATEN is not set
# CONFIG_PARIDE_BPCK is not set
# CONFIG_PARIDE_BPCK6 is not set
# CONFIG_PARIDE_COMM is not set
# CONFIG_PARIDE_DSTR is not set
# CONFIG_PARIDE_FIT2 is not set
# CONFIG_PARIDE_FIT3 is not set
# CONFIG_PARIDE_EPAT is not set
# CONFIG_PARIDE_EPIA is not set
# CONFIG_PARIDE_FRIQ is not set
# CONFIG_PARIDE_FRPW is not set
# CONFIG_PARIDE_KBIC is not set
# CONFIG_PARIDE_KTTI is not set
# CONFIG_PARIDE_ON20 is not set
# CONFIG_PARIDE_ON26 is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_CRYPTOLOOP=m
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_BLK_DEV_INITRD=y
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_LBD is not set
# CONFIG_CDROM_PKTCDVD is not set

#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
CONFIG_IOSCHED_AS=y
CONFIG_IOSCHED_DEADLINE=y
CONFIG_IOSCHED_CFQ=y
# CONFIG_ATA_OVER_ETH is not set

#
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y

#
# Please see Documentation/ide.txt for help/info on IDE drives
#
# CONFIG_BLK_DEV_IDE_SATA is not set
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set

#
# IDE chipset support/bugfixes
#
CONFIG_IDE_GENERIC=y
# CONFIG_BLK_DEV_CMD640 is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_IDEDMA_ONLYDISK is not set
# CONFIG_BLK_DEV_AEC62XX is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_BLK_DEV_ATIIXP is not set
# CONFIG_BLK_DEV_CMD64X is not set
# CONFIG_BLK_DEV_TRIFLEX is not set
# CONFIG_BLK_DEV_CY82C693 is not set
# CONFIG_BLK_DEV_CS5520 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
# CONFIG_BLK_DEV_SC1200 is not set
CONFIG_BLK_DEV_PIIX=y
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_PDC202XX_OLD is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
# CONFIG_BLK_DEV_SIIMAGE is not set
# CONFIG_BLK_DEV_SIS5513 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# CONFIG_IDE_ARM is not set
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_IVB is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_HD is not set

#
# SCSI device support
#
CONFIG_SCSI=y
CONFIG_SCSI_PROC_FS=y

#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
# CONFIG_CHR_DEV_ST is not set
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_CHR_DEV_SG=m

#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set

#
# SCSI Transport Attributes
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set

#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_3W_9XXX is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
CONFIG_SCSI_QLA2XXX=y
# CONFIG_SCSI_QLA21XX is not set
# CONFIG_SCSI_QLA22XX is not set
# CONFIG_SCSI_QLA2300 is not set
# CONFIG_SCSI_QLA2322 is not set
# CONFIG_SCSI_QLA6312 is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set

#
# PCMCIA SCSI adapter support
#
# CONFIG_PCMCIA_AHA152X is not set
# CONFIG_PCMCIA_FDOMAIN is not set
# CONFIG_PCMCIA_NINJA_SCSI is not set
# CONFIG_PCMCIA_QLOGIC is not set
# CONFIG_PCMCIA_SYM53C500 is not set

#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set

#
# Fusion MPT device support
#
# CONFIG_FUSION is not set

#
# IEEE 1394 (FireWire) support
#
# CONFIG_IEEE1394 is not set

#
# I2O device support
#
# CONFIG_I2O is not set

#
# Networking support
#
CONFIG_NET=y

#
# Networking options
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
# CONFIG_NETLINK_DEV is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_IP_TCPDIAG=y
# CONFIG_IP_TCPDIAG_IPV6 is not set

#
# IP: Virtual Server Configuration
#
# CONFIG_IP_VS is not set
# CONFIG_IPV6 is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set

#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
# CONFIG_IP_NF_CT_ACCT is not set
# CONFIG_IP_NF_CONNTRACK_MARK is not set
# CONFIG_IP_NF_CT_PROTO_SCTP is not set
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
CONFIG_IP_NF_TFTP=m
CONFIG_IP_NF_AMANDA=m
# CONFIG_IP_NF_QUEUE is not set
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_IPRANGE=m
CONFIG_IP_NF_MATCH_MAC=m
CONFIG_IP_NF_MATCH_PKTTYPE=m
CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_RECENT=m
CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_DSCP=m
CONFIG_IP_NF_MATCH_AH_ESP=m
CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_TCPMSS=m
CONFIG_IP_NF_MATCH_HELPER=m
CONFIG_IP_NF_MATCH_STATE=m
CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_MATCH_OWNER=m
# CONFIG_IP_NF_MATCH_ADDRTYPE is not set
# CONFIG_IP_NF_MATCH_REALM is not set
# CONFIG_IP_NF_MATCH_SCTP is not set
# CONFIG_IP_NF_MATCH_COMMENT is not set
# CONFIG_IP_NF_MATCH_HASHLIMIT is not set
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
CONFIG_IP_NF_TARGET_SAME=m
# CONFIG_IP_NF_NAT_SNMP_BASIC is not set
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_NAT_TFTP=m
CONFIG_IP_NF_NAT_AMANDA=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_MARK=m
CONFIG_IP_NF_TARGET_CLASSIFY=m
# CONFIG_IP_NF_RAW is not set
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m

#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set

#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set

#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_HAMRADIO is not set
CONFIG_IRDA=y

#
# IrDA protocols
#
# CONFIG_IRLAN is not set
# CONFIG_IRNET is not set
CONFIG_IRCOMM=y
# CONFIG_IRDA_ULTRA is not set

#
# IrDA options
#
# CONFIG_IRDA_CACHE_LAST_LSAP is not set
# CONFIG_IRDA_FAST_RR is not set
# CONFIG_IRDA_DEBUG is not set

#
# Infrared-port device drivers
#

#
# SIR device drivers
#
CONFIG_IRTTY_SIR=y

#
# Dongle support
#
# CONFIG_DONGLE is not set

#
# Old SIR device drivers
#
CONFIG_IRPORT_SIR=y

#
# Old Serial dongle support
#
# CONFIG_DONGLE_OLD is not set

#
# FIR device drivers
#
# CONFIG_USB_IRDA is not set
# CONFIG_SIGMATEL_FIR is not set
# CONFIG_TOSHIBA_FIR is not set
# CONFIG_VLSI_FIR is not set
# CONFIG_BT is not set
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set

#
# ARCnet devices
#
# CONFIG_ARCNET is not set

#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
CONFIG_NET_VENDOR_3COM=y
CONFIG_VORTEX=y
# CONFIG_TYPHOON is not set

#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_NET_PCI is not set

#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
# CONFIG_SKGE is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set

#
# Ethernet (10000 Mbit)
#
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set

#
# Token Ring devices
#
# CONFIG_TR is not set

#
# Wireless LAN (non-hamradio)
#
CONFIG_NET_RADIO=y

#
# Obsolete Wireless cards support (pre-802.11)
#
# CONFIG_STRIP is not set
# CONFIG_PCMCIA_WAVELAN is not set
# CONFIG_PCMCIA_NETWAVE is not set

#
# Wireless 802.11 Frequency Hopping cards support
#
# CONFIG_PCMCIA_RAYCS is not set

#
# Wireless 802.11b ISA/PCI cards support
#
CONFIG_HERMES=m
# CONFIG_PLX_HERMES is not set
# CONFIG_TMD_HERMES is not set
# CONFIG_PCI_HERMES is not set
# CONFIG_ATMEL is not set

#
# Wireless 802.11b Pcmcia/Cardbus cards support
#
# CONFIG_PCMCIA_HERMES is not set
# CONFIG_AIRO_CS is not set
# CONFIG_PCMCIA_WL3501 is not set

#
# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support
#
# CONFIG_PRISM54 is not set
CONFIG_NET_WIRELESS=y

#
# PCMCIA network device support
#
CONFIG_NET_PCMCIA=y
CONFIG_PCMCIA_3C589=m
CONFIG_PCMCIA_3C574=m
CONFIG_PCMCIA_FMVJ18X=m
CONFIG_PCMCIA_PCNET=m
CONFIG_PCMCIA_NMCLAN=m
CONFIG_PCMCIA_SMC91C92=m
CONFIG_PCMCIA_XIRC2PS=m
CONFIG_PCMCIA_AXNET=m

#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
CONFIG_PPP=m
# CONFIG_PPP_MULTILINK is not set
# CONFIG_PPP_FILTER is not set
CONFIG_PPP_ASYNC=m
# CONFIG_PPP_SYNC_TTY is not set
# CONFIG_PPP_DEFLATE is not set
# CONFIG_PPP_BSDCOMP is not set
# CONFIG_PPPOE is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set

#
# ISDN subsystem
#
# CONFIG_ISDN is not set

#
# Telephony Support
#
# CONFIG_PHONE is not set

#
# Input device support
#
CONFIG_INPUT=y

#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1400
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=1050
CONFIG_INPUT_JOYDEV=y
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set

#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
CONFIG_SERIO=y
CONFIG_SERIO_I8042=y
CONFIG_SERIO_SERPORT=y
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
# CONFIG_SERIO_PCIPS2 is not set
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set

#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
CONFIG_MOUSE_PS2=y
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_VSXXXAA is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=y
# CONFIG_INPUT_UINPUT is not set

#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set

#
# Serial drivers
#
CONFIG_SERIAL_8250=y
# CONFIG_SERIAL_8250_CONSOLE is not set
# CONFIG_SERIAL_8250_CS is not set
CONFIG_SERIAL_8250_NR_UARTS=4
# CONFIG_SERIAL_8250_EXTENDED is not set

#
# Non-8250 serial port support
#
CONFIG_SERIAL_CORE=y
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_PRINTER=m
# CONFIG_LP_CONSOLE is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set

#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set

#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
CONFIG_HW_RANDOM=y
CONFIG_NVRAM=y
CONFIG_RTC=y
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set

#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=y
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_ATI is not set
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_AMD64 is not set
CONFIG_AGP_INTEL=y
# CONFIG_AGP_INTEL_MCH is not set
# CONFIG_AGP_NVIDIA is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_EFFICEON is not set
CONFIG_DRM=y
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_R128 is not set
CONFIG_DRM_RADEON=y
# CONFIG_DRM_I810 is not set
# CONFIG_DRM_I830 is not set
# CONFIG_DRM_I915 is not set
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set

#
# PCMCIA character devices
#
# CONFIG_SYNCLINK_CS is not set
# CONFIG_MWAVE is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_HANGCHECK_TIMER is not set

#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y

#
# I2C Algorithms
#
CONFIG_I2C_ALGOBIT=y
CONFIG_I2C_ALGOPCF=y
CONFIG_I2C_ALGOPCA=y

#
# I2C Hardware Bus support
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
# CONFIG_I2C_ALI15X3 is not set
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
CONFIG_I2C_I801=y
# CONFIG_I2C_I810 is not set
# CONFIG_I2C_ISA is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_PARPORT is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
# CONFIG_I2C_PCA_ISA is not set

#
# Hardware Sensors Chip support
#
# CONFIG_I2C_SENSOR is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ASB100 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM63 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_VIA686A is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set

#
# Other I2C Chip support
#
# CONFIG_SENSORS_EEPROM is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set

#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set

#
# Misc devices
#
# CONFIG_IBM_ASM is not set

#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set

#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set

#
# Graphics support
#
CONFIG_FB=y
CONFIG_FB_MODE_HELPERS=y
# CONFIG_FB_TILEBLITTING is not set
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
CONFIG_FB_VESA=y
CONFIG_FB_VESA_STD=y
# CONFIG_FB_VESA_TNG is not set
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_HGA is not set
# CONFIG_FB_RIVA is not set
# CONFIG_FB_I810 is not set
# CONFIG_FB_INTEL is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON_OLD is not set
CONFIG_FB_RADEON=y
CONFIG_FB_RADEON_I2C=y
# CONFIG_FB_RADEON_DEBUG is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_VIRTUAL is not set

#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y

#
# Logo configuration
#
CONFIG_LOGO=y
CONFIG_LOGO_LINUX_MONO=y
CONFIG_LOGO_LINUX_VGA16=y
CONFIG_LOGO_LINUX_CLUT224=y
CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_BACKLIGHT_CLASS_DEVICE=m
CONFIG_BACKLIGHT_DEVICE=y
CONFIG_LCD_CLASS_DEVICE=m
CONFIG_LCD_DEVICE=y
CONFIG_FB_SPLASH=y

#
# Speakup console speech
#
# CONFIG_SPEAKUP is not set
CONFIG_SPEAKUP_DEFAULT="none"

#
# Sound
#
CONFIG_SOUND=y

#
# Advanced Linux Sound Architecture
#
CONFIG_SND=y
CONFIG_SND_TIMER=y
CONFIG_SND_PCM=y
CONFIG_SND_RAWMIDI=m
CONFIG_SND_SEQUENCER=y
# CONFIG_SND_SEQ_DUMMY is not set
CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_SEQUENCER_OSS=y
# CONFIG_SND_RTCTIMER is not set
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set

#
# Generic devices
#
CONFIG_SND_MPU401_UART=m
CONFIG_SND_DUMMY=m
CONFIG_SND_VIRMIDI=m
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
CONFIG_SND_MPU401=m

#
# PCI devices
#
CONFIG_SND_AC97_CODEC=y
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_ATIIXP is not set
# CONFIG_SND_ATIIXP_MODEM is not set
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_EMU10K1 is not set
# CONFIG_SND_EMU10K1X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_MIXART is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
CONFIG_SND_INTEL8X0=y
CONFIG_SND_INTEL8X0M=y
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
# CONFIG_SND_VX222 is not set

#
# USB devices
#
# CONFIG_SND_USB_AUDIO is not set
# CONFIG_SND_USB_USX2Y is not set

#
# PCMCIA devices
#

#
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set

#
# USB support
#
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_BANDWIDTH=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y

#
# USB Host Controller Drivers
#
# CONFIG_USB_EHCI_HCD is not set
# CONFIG_USB_OHCI_HCD is not set
CONFIG_USB_UHCI_HCD=y
# CONFIG_USB_SL811_HCD is not set

#
# USB Device Class drivers
#
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_MIDI is not set
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=y

#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=y
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_RW_DETECT is not set
CONFIG_USB_STORAGE_DATAFAB=y
CONFIG_USB_STORAGE_FREECOM=y
CONFIG_USB_STORAGE_ISD200=y
CONFIG_USB_STORAGE_DPCM=y
CONFIG_USB_STORAGE_HP8200e=y
CONFIG_USB_STORAGE_SDDR09=y
CONFIG_USB_STORAGE_SDDR55=y
CONFIG_USB_STORAGE_JUMPSHOT=y

#
# USB Input Devices
#
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
# CONFIG_HID_FF is not set
# CONFIG_USB_HIDDEV is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_MTOUCH is not set
# CONFIG_USB_EGALAX is not set
# CONFIG_USB_XPAD is not set
# CONFIG_USB_ATI_REMOTE is not set

#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set

#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set

#
# Video4Linux support is needed for USB Multimedia device support
#

#
# USB Network Adapters
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set

#
# USB port drivers
#
# CONFIG_USB_USS720 is not set

#
# USB Serial Converter support
#
CONFIG_USB_SERIAL=y
# CONFIG_USB_SERIAL_CONSOLE is not set
CONFIG_USB_SERIAL_GENERIC=y
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
# CONFIG_USB_SERIAL_EMPEG is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
# CONFIG_USB_SERIAL_VISOR is not set
# CONFIG_USB_SERIAL_IPAQ is not set
# CONFIG_USB_SERIAL_IR is not set
# CONFIG_USB_SERIAL_EDGEPORT is not set
# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
# CONFIG_USB_SERIAL_GARMIN is not set
# CONFIG_USB_SERIAL_IPW is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
# CONFIG_USB_SERIAL_KEYSPAN is not set
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_KOBIL_SCT is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
CONFIG_USB_SERIAL_PL2303=y
# CONFIG_USB_SERIAL_SAFE is not set
# CONFIG_USB_SERIAL_TI is not set
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
# CONFIG_USB_SERIAL_OMNINET is not set

#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYTHERM is not set
# CONFIG_USB_PHIDGETKIT is not set
# CONFIG_USB_PHIDGETSERVO is not set
# CONFIG_USB_IDMOUSE is not set
# CONFIG_USB_TEST is not set

#
# USB ATM/DSL drivers
#

#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set

#
# MMC/SD Card support
#
# CONFIG_MMC is not set

#
# InfiniBand support
#
# CONFIG_INFINIBAND is not set

#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_REISERFS_FS=y
# CONFIG_REISERFS_CHECK is not set
CONFIG_REISERFS_PROC_INFO=y
# CONFIG_REISERFS_FS_XATTR is not set
# CONFIG_JFS_FS is not set

#
# XFS support
#
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
CONFIG_ROMFS_FS=y
CONFIG_INOTIFY=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
CONFIG_AUTOFS4_FS=y

#
# CD-ROM/DVD Filesystems
#
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
CONFIG_ZISOFS_FS=y
CONFIG_UDF_FS=y
CONFIG_UDF_NLS=y

#
# DOS/FAT/NT Filesystems
#
CONFIG_FAT_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=y
# CONFIG_NTFS_DEBUG is not set
# CONFIG_NTFS_RW is not set

#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_SYSFS=y
CONFIG_DEVFS_FS=y
CONFIG_DEVFS_MOUNT=y
# CONFIG_DEVFS_DEBUG is not set
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
# CONFIG_TMPFS_XATTR is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y

#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_CRAMFS is not set
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set

#
# Network File Systems
#
CONFIG_NFS_FS=y
# CONFIG_NFS_V3 is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
CONFIG_NFSD=y
# CONFIG_NFSD_V3 is not set
# CONFIG_NFSD_TCP is not set
CONFIG_LOCKD=y
CONFIG_EXPORTFS=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
CONFIG_SMB_FS=y
# CONFIG_SMB_NLS_DEFAULT is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set

#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y

#
# Native Language Support
#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-15"
CONFIG_NLS_CODEPAGE_437=y
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
CONFIG_NLS_CODEPAGE_850=y
# CONFIG_NLS_CODEPAGE_852 is not set
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
# CONFIG_NLS_CODEPAGE_860 is not set
# CONFIG_NLS_CODEPAGE_861 is not set
# CONFIG_NLS_CODEPAGE_862 is not set
# CONFIG_NLS_CODEPAGE_863 is not set
# CONFIG_NLS_CODEPAGE_864 is not set
# CONFIG_NLS_CODEPAGE_865 is not set
# CONFIG_NLS_CODEPAGE_866 is not set
# CONFIG_NLS_CODEPAGE_869 is not set
# CONFIG_NLS_CODEPAGE_936 is not set
# CONFIG_NLS_CODEPAGE_950 is not set
# CONFIG_NLS_CODEPAGE_932 is not set
# CONFIG_NLS_CODEPAGE_949 is not set
# CONFIG_NLS_CODEPAGE_874 is not set
# CONFIG_NLS_ISO8859_8 is not set
# CONFIG_NLS_CODEPAGE_1250 is not set
# CONFIG_NLS_CODEPAGE_1251 is not set
# CONFIG_NLS_ASCII is not set
CONFIG_NLS_ISO8859_1=y
# CONFIG_NLS_ISO8859_2 is not set
# CONFIG_NLS_ISO8859_3 is not set
# CONFIG_NLS_ISO8859_4 is not set
# CONFIG_NLS_ISO8859_5 is not set
# CONFIG_NLS_ISO8859_6 is not set
# CONFIG_NLS_ISO8859_7 is not set
# CONFIG_NLS_ISO8859_9 is not set
# CONFIG_NLS_ISO8859_13 is not set
# CONFIG_NLS_ISO8859_14 is not set
CONFIG_NLS_ISO8859_15=y
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y

#
# Profiling support
#
# CONFIG_PROFILING is not set

#
# Kernel hacking
#
# CONFIG_DEBUG_KERNEL is not set
CONFIG_DEBUG_PREEMPT=y
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_FRAME_POINTER is not set
CONFIG_EARLY_PRINTK=y
# CONFIG_4KSTACKS is not set

#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set

#
# Cryptographic options
#
CONFIG_CRYPTO=y
CONFIG_CRYPTO_HMAC=y
CONFIG_CRYPTO_NULL=m
CONFIG_CRYPTO_MD4=m
CONFIG_CRYPTO_MD5=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
# CONFIG_CRYPTO_WP512 is not set
CONFIG_CRYPTO_DES=m
CONFIG_CRYPTO_BLOWFISH=m
CONFIG_CRYPTO_TWOFISH=m
CONFIG_CRYPTO_SERPENT=m
# CONFIG_CRYPTO_AES_586 is not set
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
# CONFIG_CRYPTO_TEA is not set
CONFIG_CRYPTO_ARC4=m
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_ANUBIS is not set
CONFIG_CRYPTO_DEFLATE=m
CONFIG_CRYPTO_MICHAEL_MIC=m
CONFIG_CRYPTO_CRC32C=m
# CONFIG_CRYPTO_TEST is not set

#
# Hardware crypto devices
#
# CONFIG_CRYPTO_DEV_PADLOCK is not set

#
# Library routines
#
CONFIG_CRC_CCITT=y
CONFIG_CRC32=y
CONFIG_LIBCRC32C=m
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_PC=y

jlmcp · Post by **jlmcp** » Tue Jul 05, 2005 3:32 pm

This was a valuable thread! Thanks for posting!

From what I can tell, my 7500 is working properly. Glxgears is outputting:

1500 frames in 5.0 seconds = 238.600 FPS
1375 frames in 5.0 seconds = 275.000 FPS
1375 frames in 5.0 seconds = 275.000 FPS
1500 frames in 5.0 seconds = 238.600 FPS
etc...

One (noob) question I have is: how do you know what video options will work with your graphics card in xorg.conf? Is this documented somewhere? Just an educated guess? Are there other options that I could enable for the 7500?

Just curious.

Jake

secondae · Post by **secondae** » Wed Jul 13, 2005 9:32 pm

JoKerTheFirst wrote:Thanks nrdu, you saved my life
it worked like a charm on my system
Asus L3540 (L3800-S family) , P4 1400 MHz, 256 RAM, ATI radeon mobility 7500 64Mb RAM, using gentoo-dev-sources 2.6.9-rc1 and xorg-6.8.0-r1
now I can score up to ~1200 on glxgears (was 300)

I have L3540 too.. 1.8GHz, 768MB

the first time i've installed gentoo, graphics doesn't work very well..the image was corrupted when using resolution higher than 1024x768 with kde..

serjster · Post by **serjster** » Sun Sep 04, 2005 12:27 pm

Hi, Does DRI give the same performance as if it would be with ati drivers ? What about the chipdID thing? Why cant it work with the 7500, what if u somehow edited the bios cheating the ati drivers? But maybe the chipsets are really different like in architecture and this will never work..
I almost cant play quake 3 with my ati 7500 in linux.. it makes me wanna go back to windows :\.

JellyTot · Post by **JellyTot** » Mon Oct 17, 2005 4:43 am

Thank you very much, nrdu. You helped me avert another weekend of headaches. My Mobility 7500 works fine now.

capira · Post by **capira** » Sun Jan 15, 2006 12:39 pm

Thank you very much as well, nrdu. The laptop is working now like a charm!!!

Kurous · Post by **Kurous** » Mon Mar 13, 2006 9:01 pm

Does anyone have this card working with modular xorg??? I have DRI and OpenGL set up, but any opengl apps I run segfault. I have T40 laptop.

Kurous · Post by **Kurous** » Wed Apr 26, 2006 10:23 pm

I'll take that as a no.

dizzy · Post by **dizzy** » Fri May 12, 2006 6:52 am

@Kurous

This thread is a little old, so I don't know if you still got this problem or not. I'm using this card with modular xorg. No problem with opengl. Mind you the only test I've done is with glxgears, so it might not apply to your prob.

sirformatalot · Post by **sirformatalot** » Sat May 13, 2006 3:02 pm

dizzy,
just wondering what kernel you're using- have you tried this card with Xgl? modular xorg 7.0 i presume ? my x crashes with any moderate video loads but i haven't really tried to figure out what the problem is yet- i'm lazy. what video driver are you using for this card? how'bout xorg.conf?

dizzy · Post by **dizzy** » Sun May 14, 2006 3:38 pm

@sirformatalot

I'm using gentoo-sources-2.6.16-r7. I also used x11-base/x11-drm-20051223 instead of the kernel's. I've read that there are problems with this card in Xgl, so I have not try it yet. Yes, I'm using modular xorg 7. The driver for the 7500 mobile is just "ati". It used to be "radeon" in xorg 6.8.x. IIRC.

If setup correctly, it should give you ~1500 FPS in glxgears.

My xorg.conf

Code: Select all

# ----------- [ ServerLayout section ] ---------------- #
Section "ServerLayout"
        Identifier      "Default"
        Screen          "LCD"
        InputDevice     "Keyboard0" "CoreKeyboard"
        InputDevice     "Touchpad"  "CorePointer"
EndSection

# ----------- [ Files ] ------------------------------- #
Section "Files"
        RgbPath         "/usr/share/X11/rgb"
        ModulePath      "/usr/lib/xorg/modules"
        FontPath        "/usr/share/fonts/misc:unscaled"
        FontPath        "/usr/share/fonts/corefonts"
        FontPath        "/usr/share/fonts/TTF"
        FontPath        "/usr/share/fonts/Type1"
        FontPath        "/usr/share/fonts/terminus"
        FontPath        "/usr/share/fonts/local"
        FontPath        "/usr/share/fonts/100dpi:unscaled"
        FontPath        "/usr/share/fonts/75dpi:unscaled"
EndSection

# ----------- [ Server flags ] ------------------------ #
Section "ServerFlags"
        Option  "DefaultServerLayout"   "Default"
        Option  "allowmouseopenfail"
EndSection

# ----------- [ Modules ] ----------------------------- #
Section "Module"
        Load    "dbe"
        Load    "dri"
        Load    "extmod"
        Load    "freetype"
        Load    "type1"
        Load    "glx"
        Load    "record"
        Load    "synaptics"
        Load    "xtrap"
EndSection

# ----------- [ Input devices ] ----------------------- #
Section "InputDevice"
        Identifier      "Keyboard0"
        Driver          "kbd"
        Option          "CoreKeyboard"
        Option          "XkbModel"      "pc105"
        Option          "XkbLayout"     "us"
        Option          "AutoRepeat"    "250 30"
EndSection

Section "InputDevice"
        Identifier      "Touchpad"
        Driver          "synaptics"
        Option          "CorePointer"
        Option          "Device"                "/dev/input/event3"
        Option          "Protocol"              "auto-dev"
        Option          "SHMConfig"             "on"
        Option          "LeftEdge"              "1500"
        Option          "RightEdge"             "5500"
        Option          "TopEdge"               "1400"
        Option          "BottomEdge"            "4500"
        Option          "FingerLow"             "20"
        Option          "FingerHigh"            "40"
        Option          "MaxTapTime"            "180"
        Option          "MaxTapMove"            "220"
        Option          "MaxDoubleTapTime"      "220"
        Option          "VertScrollDelta"       "100"
        Option          "HorizScrollDelta"      "100"
        Option          "EdgeMotionSpeed"       "40"
        Option          "MinSpeed"              "0.12"
        Option          "MaxSpeed"              "0.12"
        Option          "AccelFactor"           "0.0010"
        Option          "UpDownScrolling"       "1"
        Option          "RTCornerButton"        "0"
        Option          "RBCornerButton"        "0"
        Option          "LTCornerButton"        "0"
        Option          "LBCornerButton"        "0"
        Option          "TapButton1"            "0"
        Option          "TapButton2"            "2"
        Option          "TapButton3"            "0"
        Option          "EmulateMidButtonTime"  "75"
        Option          "PalmDetect"            "1"
EndSection


# ----------- [ Graphics device ] --------------------- #
Section "Device"
        Identifier      "Radeon 7500M"
        VendorName      "ATI Technologies Inc"
        BoardName       "Radeon Mobility M7 LW"
        Driver          "ati"
        Option          "SWcursor"              "off"
        Option          "NoAccel"               "off"
        Option          "Dac6Bit"               "off"
        Option          "UseFBDev"              "off"
        Option          "AGPMode"               "4"
        Option          "AGPFastWrite"          "off"
        Option          "BusType"               "AGP"
        Option          "DDCMode"               "on"
        Option          "DisplayPriority"       "BIOS"
        Option          "MonitorLayout"         "LVDS"
        Option          "EnablePageFlip"        "on"
        Option          "RenderAccel"           "on"
        #Option         "backingstore"          "true"
        Option          "SubPixelOrder"         "RGB"
        BusID           "PCI:1:0:0"
        Screen          0
EndSection


# ----------- [ Monitor section ] --------------------- #
Section "Monitor"
        Identifier      "Sony LCD"
        DisplaySize     325.1 243.8                     # Real size. Will give 125 dpi
        Option          "dpms"
EndSection

# ----------- [ Screen section ] ---------------------- #
Section "Screen"
        Identifier      "LCD"
        Device          "Radeon 7500M"
        Monitor         "Sony LCD"
        DefaultDepth    24
        SubSection "Display"
                Viewport   0 0
                Depth   1
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth   4
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth   8
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth   15
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth   16
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth   24
        EndSubSection
EndSection

# ----------- [ xorg-x11-6.8+] ------------------------ #
Section "Extensions"
        Option          "Composite"             "Enable"
EndSection

# ----------- [ Misc ] -------------------------------- #
Section "DRI"
#       Group   0
        Mode            0666
EndSection

# end of XF86Config

HOWTO: ATI Radeon Mobility 7500 and Sony GRX560 laptop

HOWTO: ATI Radeon Mobility 7500 and Sony GRX560 laptop

Everquest, Cedega and the 7500

suspend to ram

Thank you