Gentoo Forums
Gentoo Forums
Gentoo Forums
Quick Search: in
Få igång JOS 110
View unanswered posts
View posts from last 24 hours

 
Reply to topic    Gentoo Forums Forum Index Scandinavian
View previous topic :: View next topic  
Author Message
DarkVillage
n00b
n00b


Joined: 12 Sep 2003
Posts: 52
Location: SWEDEN

PostPosted: Mon Jun 28, 2004 6:20 am    Post subject: Få igång JOS 110 Reply with quote

Jag har nu under en tid försökt fått igång min JOS 110 i gentoo. Som jag har förstått ska den fungera som ett usb minne och därmed ska det gå att mounta den bara (sda1 eller liknande). Jag har ställt in i kerneln stöd för USB storage (eller vad det nu heter) men det kommer inte upp någon ny enhet i /dev

jag har sda, sda1, sda2, sda3, sda6 bl.a. i /dev

alla utom sda är partitioner i en sata disk och sda kan jag inte mounta


Snälla hjälp mig
Back to top
View user's profile Send private message
erikedin
n00b
n00b


Joined: 16 Mar 2003
Posts: 40
Location: Stockholm

PostPosted: Mon Jun 28, 2004 8:15 am    Post subject: Reply with quote

Vad du vill göra är köra kommandot
Code:
dmesg

Detta skriver ut en massa systeminformation och om du pluggar in minnet kommer du förhoppningsvis se lite information om de minnet längs ner.

Om det som står inte känns hjälpsamt kan du posta nedre delen av texten här.
_________________
#5273
<erno> hm. I've lost a machine.. literally _lost_. it responds to ping, it works completely, I just can't figure out where in my apartment it is.
- bash.org
Back to top
View user's profile Send private message
DarkVillage
n00b
n00b


Joined: 12 Sep 2003
Posts: 52
Location: SWEDEN

PostPosted: Mon Jun 28, 2004 7:35 pm    Post subject: Reply with quote

Hjälpte tyvärr inte mig så mycket, det verkar ju som mass storage funkar, men den hittar ju inte spelaren

detta är en del ur dmesg:

libata version 1.02 loaded.
sata_sil version 0.54
ata1: SATA max UDMA/100 cmd 0xE080C080 ctl 0xE080C08A bmdma 0xE080C000 irq 16
ata2: SATA max UDMA/100 cmd 0xE080C0C0 ctl 0xE080C0CA bmdma 0xE080C008 irq 16
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 234441648 sectors (lba48)
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: no device found (phy stat 00000000)
ata2: thread exiting
scsi1 : sata_sil
Vendor: ATA Model: ST3120026AS Rev: 1.02
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
SCSI device sda: drive cache: write through
/dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
ohci1394: $Rev: 1172 $ Ben Collins <bcollins@debian.org>
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17] MMIO=[e9082000-e90827ff] Max
Packet=[2048]
ieee1394: raw1394: /dev/raw1394 device initialized
ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 21, pci mem e0814000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
USB Universal Host Controller Interface driver v2.2
drivers/usb/core/usb.c: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
drivers/usb/core/usb.c: registered new driver usb-storage
USB Mass Storage support registered.
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver


jag har väll hlömt något i kerneln, men vad.....
Back to top
View user's profile Send private message
erikedin
n00b
n00b


Joined: 16 Mar 2003
Posts: 40
Location: Stockholm

PostPosted: Tue Jun 29, 2004 6:21 am    Post subject: Reply with quote

Har du kompilerat in OHCI HCD support och/eller UHCI HDC support?
_________________
#5273
<erno> hm. I've lost a machine.. literally _lost_. it responds to ping, it works completely, I just can't figure out where in my apartment it is.
- bash.org
Back to top
View user's profile Send private message
DarkVillage
n00b
n00b


Joined: 12 Sep 2003
Posts: 52
Location: SWEDEN

PostPosted: Tue Jun 29, 2004 3:50 pm    Post subject: Reply with quote

erikedin wrote:
Har du kompilerat in OHCI HCD support och/eller UHCI HDC support?


OHCI HCD support gjorde susen, kännde inte till det... tack för hjälpen
Back to top
View user's profile Send private message
Display posts from previous:   
Reply to topic    Gentoo Forums Forum Index Scandinavian All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum