HP 8200 CD-burner does not work

[2mies]

Hi

I have problems with my HP 8200 cd-burner. Everything seems to be ok but when I tried to burn a new cd both xcdroast and cdbakeoven failed.

Here is the log file from cdbakeoven

Starting burn process!
scsidev: '00,00,00'
scsibus: 0 target: 0 lun: 0
Linux sg driver version: 3.1.24
Cdrecord 1.11a34 (i686-pc-linux-gnu) Copyright (C) 1995-2002 Jörg Schilling
TOC Type: 1 = CD-ROM
Using libscg version 'schily-0.6'
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 1
Vendor_info : 'HP '
Identifikation : 'CD-Writer+ 8200 '
Revision : '1.0f'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags : MMC SWABAUDIO
Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
Drive buf size : 2086656 = 2037 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 6 MB
Total size: 7 MB (00:42.90) = 3218 sectors
Lout start: 7 MB (00:44/6 = 3218 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 5
Reference speed: 2
Is not unrestricted
Is erasable
ATIP start of lead in: -11625 (97:27/00)
ATIP start of lead out: 333750 (74:12/00)
1T speed low: 2 1T speed high: 2
power mult factor: 5 6
recommended erase/write power: 3
A1 values: 11 5C B0
Disk type: Phase change
Manuf. index: 0
Manufacturer: Illegal Manufacturer code
Blocks total: 333750 Blocks current: 321750 Blocks remaining: 318532
RBlocks total: 336246 RBlocks current: 324246 RBlocks remaining: 321028
Starting to write CD/DVD at speed 2 in real TAO mode for multi session.
Last chance to quit, starting real write in 1 seconds.
0 seconds. Operation starts.
Waiting for reader process to fill input buffer ...
input buffer ready.
Performing OPC...
Burning Track 0 of 6 MB written., percent done:
0% : 0 of 6 MB written.
cdrecord: Input/output error. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 00 2E E0 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 12 00 00 00 00 24 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x24 Qual 0x00 (invalid field in cdb) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.003s timeout 40s
Sense Bytes: 70 00 00 00 00 00 00 12 00 00 00 00 00 00 00 00 00 00
write track data: error after 0 bytes
Writing time: 10.541s
Average write speed 8.5x.
Fixating...
Fixating time: 0.005s
cdrecord: fifo had 64 puts and 1 gets.
cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
Burn failed!

[thegarbageman]

I have the same model CD-Writer. Some things to check:

Do you have "SCSI Emulation Support" in your kernel (from ATA/IDE/MFM/RLL support)?

If so, do you have the line hdx=ide-scsi in you boot loader?

Do you have "SCSI CD-ROM support" enabled? (from SCSI Support)

Ah - Did you "Enable Vendor Specific Extensions"

Also, try the command: